SNVSC42 September   2023 LMQ644A2-Q1

PRODMIX  

1.   1
2. 1 Features
3. 2 Applications
4. 3 Description
5. 4 Revision History
6. 5 Device Comparison Table
7. 6 Pin Configuration and Functions
   1. 6.1 Wettable Flanks
8. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 Typical Characteristics
9. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1  Input Voltage Range (VIN)
      2. 8.3.2  Enable EN Pin and Use as VIN UVLO
      3. 8.3.3  Output Voltage Selection and Soft Start
      4. 8.3.4  SYNC Allows Clock Synchronization and Mode Selection
      5. 8.3.5  Clock Locking
      6. 8.3.6  Adjustable Switching Frequency
      7. 8.3.7  Power-Good Output Voltage Monitoring
      8. 8.3.8  Internal LDO, VCC UVLO, and BIAS Input
      9. 8.3.9  Bootstrap Voltage and VCBOOT-UVLO (CB1 and CB2 Pin)
      10. 8.3.10 CONFIG Device Configuration Pin
      11. 8.3.11 Spread Spectrum
      12. 8.3.12 Soft Start and Recovery From Dropout
      13. 8.3.13 Overcurrent and Short-Circuit Protection
      14. 8.3.14 Hiccup
      15. 8.3.15 Thermal Shutdown
   4. 8.4 Device Functional Modes
      1. 8.4.1 Shutdown Mode
      2. 8.4.2 Standby Mode
      3. 8.4.3 Active Mode
         1. 8.4.3.1 Peak Current Mode Operation
         2. 8.4.3.2 Auto Mode Operation
            1. 8.4.3.2.1 Diode Emulation
         3. 8.4.3.3 FPWM Mode Operation
         4. 8.4.3.4 Minimum On-time (High Input Voltage) Operation
         5. 8.4.3.5 Dropout
         6. 8.4.3.6 Recovery from Dropout
         7. 8.4.3.7 Other Fault Modes
10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
       1. 9.2.1 Design Requirements
       2. 9.2.2 Detailed Design Procedure
          1. 9.2.2.1  Choosing the Switching Frequency
          2. 9.2.2.2  Setting the Output Voltage
          3. 9.2.2.3  Inductor Selection
          4. 9.2.2.4  Output Capacitor Selection
          5. 9.2.2.5  Input Capacitor Selection
          6. 9.2.2.6  BOOT Capacitor
          7. 9.2.2.7  VCC
          8. 9.2.2.8  CFF and RFF Selection
          9. 9.2.2.9  SYNCHRONIZATION AND MODE
          10. 9.2.2.10 External UVLO
          11. 9.2.2.11 Typical Thermal Performance
       3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
       1. 9.4.1 Layout Guidelines
          1. 9.4.1.1 Ground and Thermal Considerations
       2. 9.4.2 Layout Example
11. 10Device and Documentation Support
    1. 10.1 Device Support
       1. 10.1.1 Third-Party Products Disclaimer
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Glossary
    6. 10.6 Electrostatic Discharge Caution
12. 11Mechanical, Packaging, and Orderable Information

LMQ644xx-Q1 3-V to 36-V, Low I_Q, Dual 6/5/4-A Automotive Buck Converter Optimized for Power Density and Low EMI