SLLSEQ6A September   2016  – September 2016 ONET1131EC

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Function
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 DC Electrical Characteristics
    6. 6.6 AC Electrical Characteristics
    7. 6.7 Timing Requirements
    8. 6.8 Timing Diagram Definitions
    9. 6.9 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Equalizer
      2. 7.3.2 CDR
      3. 7.3.3 Modulator Driver
      4. 7.3.4 Modulation Current Generator
      5. 7.3.5 DC Offset Cancellation and Cross Point Control
      6. 7.3.6 Bias Current Generation and APC Loop
      7. 7.3.7 Laser Safety Features and Fault Recovery Procedure
      8. 7.3.8 Analog Block
        1. 7.3.8.1 Analog Reference and Temperature Sensor
        2. 7.3.8.2 Power-On Reset
        3. 7.3.8.3 Analog to Digital Converter
          1. 7.3.8.3.1 Temperature
          2. 7.3.8.3.2 Power Supply Voltage
          3. 7.3.8.3.3 Photodiode Current Monitor
          4. 7.3.8.3.4 Bias Current Monitor
        4. 7.3.8.4 2-Wire Interface and Control Logic
        5. 7.3.8.5 Bus Idle
        6. 7.3.8.6 Start Data Transfer
        7. 7.3.8.7 Stop Data Transfer
        8. 7.3.8.8 Data Transfer
      9. 7.3.9 Acknowledge
    4. 7.4 Device Functional Modes
      1. 7.4.1 Differential Transmitter Output
      2. 7.4.2 Single-Ended Transmitter Output
    5. 7.5 Programming
    6. 7.6 Register Mapping
      1. 7.6.1 R/W Control Registers
        1. 7.6.1.1 Core Level Register 0 (offset = 0100 0001 [reset = 41h]
        2. 7.6.1.2 Core Level Register 1 (offset = 0000 0000) [reset = 0h]
        3. 7.6.1.3 Core Level Register 2 (offset = 0000 0000 ) [reset = 0h]
        4. 7.6.1.4 Core Level Register 3 (offset = 0000 0000) [reset = 0h]
      2. 7.6.2 TX Registers
        1. 7.6.2.1  TX Register 10 (offset = 0000 0000) [reset = 0h]
        2. 7.6.2.2  TX Register 11 (offset = 0000 0000) [reset = 0h]
        3. 7.6.2.3  TX Register 12 (offset = 0000 0000) [reset = 0h]
        4. 7.6.2.4  TX Register 13 (offset = 0h) [reset = 0]
        5. 7.6.2.5  TX Register 14 (offset = 0000 0000) [reset = 0h]
        6. 7.6.2.6  TX Register 15 (offset = 0000 0000) [reset = 0h]
        7. 7.6.2.7  TX Register 16 (offset = 0000 0000) [reset = 0h]
        8. 7.6.2.8  TX Register 17 (offset = 0000 0000) [reset = 0h]
        9. 7.6.2.9  TX Register 18 (offset = 0000 0000) [reset = 0h]
        10. 7.6.2.10 TX Register 19 (offset = 0000 0000) [reset = 0h]
      3. 7.6.3 Reserved Registers
        1. 7.6.3.1 Reserved Registers 20-39
      4. 7.6.4 Read Only Registers
        1. 7.6.4.1 Core Level Register 40 (offset = 0000 0000) [reset = 0h]
        2. 7.6.4.2 Core Level Register 41 (offset = 0000 0000) [reset = 0h]
        3. 7.6.4.3 TX Register 43 (offset = 0000 0000) [reset = 0h]
      5. 7.6.5 Adjustment Registers
        1. 7.6.5.1 Adjustment Registers 44-50
        2. 7.6.5.2 Adjustment Register 51 (offset = 0100 0000) [reset = 40h]
        3. 7.6.5.3 Adjustment Registers 52-55
  8. 8 Application Information and Implementations
    1. 8.1 Application Information
    2. 8.2 Typical Application, Transmitter Differential Mode
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curve
      4. 8.2.4 Typical Application, Transmitter Single-Ended Mode
        1. 8.2.4.1 Design Requirements
        2. 8.2.4.2 Detailed Design Procedure
        3. 8.2.4.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Community Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

4 Revision History

Changes from * Revision (September 2016) to A Revision

  • Deleted sentence "however, this function..." from the second paragraph of the CDR sectionGo
  • Deleted the RX Registers section from Register Mapping Go
  • Deleted sentence "RX_CDRBP must be set to 1 for this function to operate." From Bit 3 of Table 6Go
  • Deleted the RX Registers 42 (offset = 0000 0000 [reset = 0h] section from Register Mapping Go