SLUSAQ4G October   2011  – September 2022 TPS40422

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Description (continued)
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  PMBus Interface Protocol General Description
      2. 8.3.2  Voltage Reference
      3. 8.3.3  Output Voltage
      4. 8.3.4  Voltage Feed Forward
      5. 8.3.5  Current Sensing
      6. 8.3.6  Overcurrent Protection
      7. 8.3.7  Current Sharing
      8. 8.3.8  Linear Regulators
      9. 8.3.9  BP Switch-over
      10. 8.3.10 Switching Frequency Setting
      11. 8.3.11 Switching Node and BOOT Voltage
      12. 8.3.12 Reading the Output Current
      13. 8.3.13 Soft-Start Time
      14. 8.3.14 Turn-On/Turn-Off Delay and Sequencing
      15. 8.3.15 Pre-Biased Output Start-Up
      16. 8.3.16 Undervoltage Lockout
      17. 8.3.17 Overvoltage and Undervoltage Fault Protection
      18. 8.3.18 Power Good
      19. 8.3.19 Overtemperature Fault Protection
      20. 8.3.20 Thermal Shutdown
      21. 8.3.21 Programmable Fault Responses
      22. 8.3.22 User Data
      23. 8.3.23 Adjustable Anti-Cross Conduction Delay
      24. 8.3.24 Connection of Unused Pins
    4. 8.4 Device Functional Modes
      1. 8.4.1 Control Signal
      2. 8.4.2 OPERATION Command
      3. 8.4.3 Control Signal and OPERATION Command
      4. 8.4.4 Two-Phase Mode Operation
    5. 8.5 Programming
      1. 8.5.1 Supported PMBus Commands
        1. 8.5.1.1 PMBus Address
        2. 8.5.1.2 PMBus Connections
        3. 8.5.1.3 PMBus Data Format
        4. 8.5.1.4 PMBus Interface Output Voltage Adjustment
        5. 8.5.1.5 53
    6. 8.6 Register Maps
      1. 8.6.1 Supported Commands
        1. 8.6.1.1  PAGE (00h)
        2. 8.6.1.2  OPERATION (01h)
          1. 8.6.1.2.1 On
          2. 8.6.1.2.2 Margin
        3. 8.6.1.3  ON_OFF_CONFIG (02h)
          1. 8.6.1.3.1 pu
          2. 8.6.1.3.2 cmd
          3. 8.6.1.3.3 CPR
          4. 8.6.1.3.4 pol
          5. 8.6.1.3.5 CPA
        4. 8.6.1.4  CLEAR_FAULTS (03h)
        5. 8.6.1.5  WRITE_PROTECT (10h)
          1. 8.6.1.5.1 bit5
          2. 8.6.1.5.2 bit6
          3. 8.6.1.5.3 bit7
        6. 8.6.1.6  STORE_USER_ALL (15h)
        7. 8.6.1.7  RESTORE_USER_ALL (16h)
        8. 8.6.1.8  CAPABILITY (19h)
        9. 8.6.1.9  VOUT_MODE (20h)
          1. 8.6.1.9.1 Mode:
          2. 8.6.1.9.2 Exponent
        10. 8.6.1.10 VIN_ON (35h)
          1. 8.6.1.10.1 Exponent
          2. 8.6.1.10.2 Mantissa
        11. 8.6.1.11 VIN_OFF (36h)
          1. 8.6.1.11.1 Exponent
          2. 8.6.1.11.2 Mantissa
        12. 8.6.1.12 IOUT_CAL_GAIN (38h)
          1. 8.6.1.12.1 Exponent
          2. 8.6.1.12.2 Mantissa
        13. 8.6.1.13 IOUT_CAL_OFFSET (39h)
          1. 8.6.1.13.1 Exponent
          2. 8.6.1.13.2 Mantissa
        14. 8.6.1.14 IOUT_OC_FAULT_LIMIT (46h)
          1. 8.6.1.14.1 Exponent
          2. 8.6.1.14.2 Mantissa
        15. 8.6.1.15 IOUT_OC_FAULT_RESPONSE (47h)
          1. 8.6.1.15.1 RS[2:0]
        16. 8.6.1.16 IOUT_OC_WARN_LIMIT (4Ah)
          1. 8.6.1.16.1 Exponent
          2. 8.6.1.16.2 Mantissa
        17. 8.6.1.17 OT_FAULT_LIMIT (4Fh)
          1. 8.6.1.17.1 Exponent
          2. 8.6.1.17.2 Mantissa
        18. 8.6.1.18 OT_WARN_LIMIT (51h)
          1. 8.6.1.18.1 Exponent
          2. 8.6.1.18.2 Mantissa
        19. 8.6.1.19 TON_RISE (61h)
          1. 8.6.1.19.1 Exponent
          2. 8.6.1.19.2 Mantissa
        20. 8.6.1.20 STATUS_BYTE (78h)
        21. 8.6.1.21 STATUS_WORD (79h)
        22. 8.6.1.22 STATUS_VOUT (7Ah)
        23. 8.6.1.23 STATUS_IOUT (7Bh)
        24. 8.6.1.24 STATUS_TEMPERATURE (7Dh)
        25. 8.6.1.25 STATUS_CML (7Eh)
        26. 8.6.1.26 STATUS_MFR_SPECIFIC (80h)
        27. 8.6.1.27 READ_VOUT (8Bh)
        28. 8.6.1.28 READ_IOUT (8Ch)
          1. 8.6.1.28.1 Exponent
          2. 8.6.1.28.2 Mantissa
        29. 8.6.1.29 READ_TEMPERATURE_2 (8Eh)
          1. 8.6.1.29.1 Exponent
          2. 8.6.1.29.2 Mantissa
        30. 8.6.1.30 PMBUS_REVISION (98h)
        31. 8.6.1.31 MFR_SPECIFIC_00 (D0h)
        32. 8.6.1.32 VREF_TRIM (MFR_SPECIFIC_04) (D4h)
        33. 8.6.1.33 STEP_VREF_MARGIN_HIGH (MFR_SPECIFIC_05) (D5h)
        34. 8.6.1.34 STEP_VREF_MARGIN_LOW (MFR_SPECIFIC_06) (D6h)
        35. 8.6.1.35 PCT_VOUT_FAULT_PG_LIMIT (MFR_SPECIFIC_07) (D7h)
        36. 8.6.1.36 126
        37. 8.6.1.37 SEQUENCE_TON_TOFF_DELAY (MFR_SPECIFIC_08) (D8h)
        38. 8.6.1.38 128
        39. 8.6.1.39 OPTIONS (MFR_SPECIFIC_21) (E5h)
        40. 8.6.1.40 DEVICE_CODE (MFR_SPECIFIC_44) (FCh)
          1. 8.6.1.40.1 Identifier Code
          2. 8.6.1.40.2 Revision Code
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Dual-Output Converter
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Custom Design with WEBENCH® Tools
          2. 9.2.1.2.2 Step 1: Inductor Selection
          3. 9.2.1.2.3 Step 2: Output Capacitor Selection
          4. 9.2.1.2.4 Step 3: Input Capacitance Selection
          5. 9.2.1.2.5 Step 4: MOSFET Selection
          6. 9.2.1.2.6 Step 5: Snubber Circuit Design
          7. 9.2.1.2.7 Step 6: Soft-Start Time
          8. 9.2.1.2.8 Step 7: Peripheral Component Design
            1. 9.2.1.2.8.1 RT (Pin 1) Switching Frequency Setting
            2. 9.2.1.2.8.2 FB1 (Pin 2) and FB2 (Pin 8) Output Voltage Setting
            3. 9.2.1.2.8.3 Compensation Network Using COMP1 (Pin 3) , COMP2 (Pin 7), FB1 (Pin 2) FB2 DIFFO1 (Pin 8) (Pin 39)
            4. 9.2.1.2.8.4 Remote Sensing Using VSNS1 (Pin 37), GSNS1 (Pin 38) , VSNS2 (Pin 15), and GSNS2 (Pin 14)
            5. 9.2.1.2.8.5 Temperate Sensing Using TSNS1 (Pin36) and TSNS2 (Pin 16)
            6. 9.2.1.2.8.6 Current Sensing Network Design Using CS1P (Pin 34), CS1N (Pin 35) , CS2P (Pin 18), and CS2N (Pin 17)
            7. 9.2.1.2.8.7 PMBus Address ADDR1 (Pin 9) , and ADDR0 (Pin 10)
            8. 9.2.1.2.8.8 Voltage Decoupling Capacitors
              1. 9.2.1.2.8.8.1  VDD (Pin 31)
              2. 9.2.1.2.8.8.2  BP3 (Pin 32)
              3. 9.2.1.2.8.8.3  BNEXT (Pin 24)
              4. 9.2.1.2.8.8.4  BP6 (Pin 25)
              5. 9.2.1.2.8.8.5  Power Good PGOOD1 (Pin 33), PGOOD2 (Pin 19)
              6. 9.2.1.2.8.8.6  Bootstrap Capacitors BOOT1 (Pin 30), and BOOT2 (Pin 20)
              7. 9.2.1.2.8.8.7  High-Side MOSFET (Gate) Resistor
              8. 9.2.1.2.8.8.8  Synchronization Setting SYNC (Pin 40)
              9. 9.2.1.2.8.8.9  BP6 (Pin 25)
              10. 9.2.1.2.8.8.10 DIFFO (Pin 39)
        3. 9.2.1.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 PCB Layout Guidelines
      2. 11.1.2 MOSFET Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Output Voltage

The TPS4022 device sets the output voltage in a way that is very similar to a traditional analog controller by using a voltage divider from the output to the FB (feedback) pin. The output voltage must be divided down to the nominal reference voltage of 600 mV. Figure 8-1 shows the typical connections for the controller. The device senses the voltage at the load by using the unity gain differential voltage sense amplifier. This functionality provides better load regulation for output voltages lower than 5-V nominal (see the Section 7.5 table for the maximum output voltage specification for the differential sense amplifier). For output voltages above this level, connect the output voltage directly to the junction of R1 and C1, leave DIFFO1 open, and do not connect the VSNS1 pin to the output voltage. The differential amplifier may also be used elsewhere in the overall system as a voltage buffer, provided the electrical specifications are not exceeded.

GUID-65CFD52F-1512-4607-BC96-92D1D1565F6E-low.gifFigure 8-1 Setting the Output Voltage

The components shown in Figure 8-1 that determine the nominal output voltage are R1 and R2. In most cases, choose a value for R to ensure the feedback compensation values (R3, R4, C1, C2 and C3) come close to readily available standard values. A value for R2 is then calculated in Equation 1.

Equation 1. GUID-0229E525-B674-4CA7-88DD-9E3FB5F7DFA3-low.gif

where

  • VFB is the feedback voltage
  • VOUT is the desired output voltage
  • R1 and R2 are in the same unit
Note:

There is no DIFFO2 pin. In dual-output mode, VSNS2 and GSNS2 are connected to the load for channel 2 and the device uses the DIFFO2 signal internally to provide voltage monitoring. Connect the output directly to the junction of R1 and C1 for channel 2 to set the output voltage and for feedback.

The DIFFO1 pin operates at voltages up to (VBP6–0.2 V). If the voltage between the VSNS1 and GSNS1 pins is higher than (VBP6–0.2 V) during any condition, the output voltage moves out of regulation because the DIFFO1 voltage is limited by BP6. To prevent this from happening, the BP6 voltage must be pre-biased before the PWM turns on, and (VBP6–0.2 V) must remain higher than the voltage between the VSNS1 and GSNS1 pins until the PWM turns off.

The feedback voltage can be changed to a value between –30% and +10% from the nominal 600 mV using PMBus commands. This adjustment allows the output voltage to vary by the same percentage. See the Section 8.5.1 section for more details.