SBOS458H December   2008  – June 2015 THS4521 , THS4522 , THS4524

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics: VS+ - VS- = 3.3 V
    6. 7.6 Electrical Characteristics: VS+ - VS- = 5 V
    7. 7.7 Typical Characteristics
    8. 7.8 Typical Characteristics: VS+ - VS- = 3.3 V
    9. 7.9 Typical Characteristics: 5 V
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Frequency Response
      2. 8.3.2  Distortion
      3. 8.3.3  Slew Rate, Transient Response, Settling Time, Output Impedance, Overdrive, Output Voltage, and Turn-On/Turn-Off Time
      4. 8.3.4  Common-Mode and Power-Supply Rejection
      5. 8.3.5  VOCM Input
      6. 8.3.6  Typical Performance Variation With Supply VoltageTypical Performance Variation with Supply Voltage section
      7. 8.3.7  title of Single-Supply Operation sectionSingle-Supply Operation
      8. 8.3.8  Low-Power Applications and the Effects of Resistor Values on Bandwidth
      9. 8.3.9  Frequency Response Variation due to Package Options
      10. 8.3.10 Driving Capacitive Loads
      11. 8.3.11 Audio Performance
      12. 8.3.12 Audio On/Off Pop Performance
    4. 8.4 Device Functional Modes
      1. 8.4.1 Operation from Single-Ended Sources to Differential Outputs
        1. 8.4.1.1 AC-Coupled Signal Path Considerations for Single-Ended Input to Differential Output Conversion
        2. 8.4.1.2 DC-Coupled Input Signal Path Considerations for Single-Ended to Differential Conversion
        3. 8.4.1.3 Resistor Design Equations for the Single-Ended to Differential Configuration of the FDA
        4. 8.4.1.4 Input Impedance for the Single-Ended to Differential FDA Configuration
      2. 8.4.2 Differential-Input to Differential-Output Operation
        1. 8.4.2.1 AC-Coupled, Differential-Input to Differential-Output Design Issues
    5. 8.5 Programming
      1. 8.5.1 Input Common-Mode Voltage Range
        1. 8.5.1.1 Setting the Output Common-Mode Voltage
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Audio ADC Driver Performance: THS4521 and PCM4204 Combined Performance
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Audio ADC Driver Performance: THS4521 and PCM3168 Combined Performance
        3. 9.2.1.3 Application Curves
      2. 9.2.2 ADC Driver Performance: THS4521 and ADS1278 Combined Performance
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
          1. 9.2.2.2.1 ADC Driver Performance: THS4521 and ADS8321 Combined Performance
        3. 9.2.2.3 Application Curves
      3. 9.2.3 Differential Input to Differential Output Amplifier
      4. 9.2.4 Single-Ended Input to Differential Output Amplifier
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Related Links
    3. 12.3 Community Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7 Specifications

7.1 Absolute Maximum Ratings

Over operating free-air temperature range (unless otherwise noted).(1)
MIN MAX UNIT
Supply voltage, VS– to VS+ 5.5 V
Input/output voltage, VI (VIN±, VOUT±, VOCM pins) (VS–) – 0.7 (VS+) + 0.7 V
Differential input voltage, VID 1 V
Output current, IO 100 mA
Input current, II (VIN±, VOCM pins) 10 mA
Continuous power dissipation See Thermal Information table
Maximum junction temperature, TJ 150 °C
Maximum junction temperature, TJ (continuous operation, long-term reliability) 125 °C
Operating free-air temperature, TA –40 85 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

7.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1) ±1300 V
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins(2) ±1000
Machine model (MM) ±50
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
VS+ single-supply voltage 2.7 5.0 5.4 V
TA Ambient temperature –40 25 85 °C

7.4 Thermal Information

THERMAL METRIC(1) THS4521 THS4522 THS4524 UNIT
D DGK PW DBT
8 PINS 8 PINS 16 PINS 38 PINS
RθJA Junction-to-ambient thermal resistance 127.8 193.8 124.2 106.2 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 81.8 84.1 62.8 60.9
RθJB Junction-to-board thermal resistance 68.3 115.3 68.5 65.5
ψJT Junction-to-top characterization parameter 32.2 17.9 15.8 18.5
ψJB Junction-to-board characterization parameter 67.8 113.6 68 65.1
RθJC(bot) Junction-to-case (bottom) thermal resistance N/A N/A N/A N/A
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.

7.5 Electrical Characteristics: VS+ – VS– = 3.3 V

At VS+ = 3.3 V, VS– = 0 V, VOCM = open, VOUT = 2 VPP (differential), RL = 1 kΩ differential, G = 1 V/V, single-ended input, differential output, and input and output referenced to midsupply, unless otherwise noted.
PARAMETER TEST CONDITIONS TEST LEVEL(1) MIN TYP MAX UNIT
AC PERFORMANCE
Small-signal bandwidth VOUT = 100 mVPP, G = 1 C 135 MHz
VOUT = 100 mVPP, G = 2 C 49 MHz
VOUT = 100 mVPP, G = 5 C 18.6 MHz
VOUT = 100 mVPP, G = 10 C 9.3 MHz
Gain bandwidth product VOUT = 100 mVPP, G = 10 C 93 MHz
Large-signal bandwidth VOUT = 2 VPP, G = 1 C 95 MHz
Bandwidth for 0.1-dB flatness VOUT = 2 VPP, G = 1 C 20 MHz
Rising slew rate (differential) VOUT = 2-V Step, G = 1, RL = 200 Ω C 420 V/μs
Falling slew rate (differential) VOUT = 2-V Step, G = 1, RL = 200 Ω C 460 V/μs
Overshoot VOUT = 2-V Step, G = 1, RL = 200 Ω C 1.2%
Undershoot VOUT = 2-V Step, G = 1, RL = 200 Ω C 2.1%
Rise time VOUT = 2-V Step, G = 1, RL = 200 Ω C 4 ns
Fall time VOUT = 2-V Step, G = 1, RL = 200 Ω C 3.5 ns
Settling time to 1% VOUT = 2-V Step, G = 1, RL = 200 Ω C 13 ns
HARMONIC DISTORTION
2nd harmonic f = 1 MHz, VOUT = 2 VPP, G = 1 C –85 dBc
f = 1 kHz, VOUT = 1 VRMS, G = 1(3),
differential input		 C –133 dBc
3rd harmonic f = 1 MHz, VOUT = 2 VPP, G = 1 C –90 dBc
f = 1 kHz, VOUT = 1 VRMS, G = 1(3),
differential input		 C –141 dBc
Second-order intermodulation distortion Two-tone, f1 = 2 MHz, f2 = 2.2 MHz,
VOUT = 2-VPP envelope		 C –83 dBc
Third-order intermodulation distortion Two-tone, f1 = 2 MHz, f2 = 2.2 MHz,
VOUT = 2-VPP envelope		 C –90 dBc
Input voltage noise f > 10 kHz C 4.6 nV/√Hz
Input current noise f > 100 kHz C 0.6 pA/√Hz
Overdrive recovery time Overdrive = ±0.5 V C 80 ns
Output balance error VOUT = 100 mV, f ≤ 2 MHz (differential input) C –57 dB
Closed-loop output impedance f = 1 MHz (differential) C 0.3 Ω
Channel-to-channel crosstalk (THS4522, THS4524) f = 10 kHz, measured differentially C –125 dB
DC PERFORMANCE
Open-loop voltage gain (AOL) A 100 116 dB
Input-referred offset voltage TA = +25°C A ±0.2 ±2 mV
TA = –40°C to +85°C B ±0.5 ±3.5 mV
Input offset voltage drift(2) TA = –40°C to +85°C C ±2 μV/°C
Input bias current(4) TA = +25°C B 0.65 0.85 μA
TA = –40°C to +85°C B 0.75 0.95 μA
Input bias current drift(2) TA = –40°C to +85°C B ±1.75 ±2 nA/°C
Input offset current TA = +25°C B ±30 ±180 nA
TA = –40°C to +85°C B ±30 ±215 nA
Input offset current drift(2) TA = –40°C to +85°C B ±100 ±600 pA/°C
INPUT
Common-mode input voltage low TA = +25°C A –0.2 –0.1 V
TA = –40°C to +85°C B –0.1 0 V
Common-mode input voltage high TA = +25°C A 1.9 2 V
TA = –40°C to +85°C B 1.8 1.9 V
Common-mode rejection ratio (CMRR) A 80 100 dB
Input impedance C 0.7 pF kΩ∥pF
OUTPUT
Output voltage low TA = +25°C A 0.08 0.15 V
TA = –40°C to +85°C B 0.09 0.2 V
Output voltage high TA = +25°C A 3.0 3.1 V
TA = –40°C to +85°C B 2.95 3.05 V
Output current drive (for linear operation) RL = 50 Ω C ±35 mA
POWER SUPPLY
Specified operating voltage B 2.5 3.3 5.5 V
Quiescent operating current, per channel TA = +25°C A 0.9 1.0 1.2 mA
TA = –40°C to +85°C B 0.85 1.0 1.25 mA
Power-supply rejection ratio (±PSRR) A 80 100 dB
POWER DOWN
Enable voltage threshold Assured on above 2.1 V A 1.6 2.1 V
Disable voltage threshold Assured off below 0.7 V A 0.7 1.6 V
Disable pin bias current C 1 μA
Power-down quiescent current C 10 μA
Turn-on time delay Time to VOUT = 90% of final value, VIN= 2 V, RL = 200 Ω B 108 ns
Turn-off time delay Time to VOUT = 10% of original value, VIN= 2 V, RL = 200 Ω B 88 ns
VOCM VOLTAGE CONTROL
Small-signal bandwidth C 23 MHz
Slew rate C 55 V/μs
Gain A 0.98 0.99 1.02 V/V
Common-mode offset voltage from VOCM input Measured at VOUT with VOCM input driven, VOCM = 1.65 V ±0.5 V B ±2.5 ±4 mV
Input bias current VOCM = 1.65 V ±0.5 V B ±5 ±8 μA
VOCM voltage range A 1 0.8 to 2.5 2.3 V
Input impedance C 72∥1.5 kΩ∥pF
Default output common-mode voltage offset from (VS+– VS–) / 2 Measured at VOUT with VOCM input open A ±1.5 ±5 mV
(1) Test levels: (A) 100% tested at 25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information.
(2) Input offset voltage drift, input bias current drift, input offset current drift, and VOCM drift are average values calculated by taking data at the maximum-range ambient-temperature end points, computing the difference, and dividing by the temperature range. Maximum drift is set by the distribution of a large sampling of devices. Drift is not specified by a test or a quality assurance (QA) sample test.
(3) Not directly measurable; calculated using noise gain of 101 as described in the Applications section, Audio Performance.
(4) Input bias current is positive out of the device.

7.6 Electrical Characteristics: VS+ – VS– = 5 V

At VS+ = 5 V, VS– = 0 V, VOCM = open, VOUT = 2 VPP (differential), RF = 1 kΩ, RL = 1 kΩ differential, G = 1 V/V, single-ended input, differential output, input and output referenced to midsupply, unless otherwise noted.
PARAMETER TEST CONDITIONS TEST LEVEL(1) MIN TYP MAX UNIT
AC PERFORMANCE
Small-signal bandwidth VOUT = 100 mVPP, G = 1 C 145 MHz
VOUT = 100 mVPP, G = 2 C 50 MHz
VOUT = 100 mVPP, G = 5 C 20 MHz
VOUT = 100 mVPP, G = 10 C 9.5 MHz
Gain bandwidth product VOUT = 100 mVPP, G = 10 C 95 MHz
Large-signal bandwidth VOUT = 2 VPP, G = 1 C 145 MHz
Bandwidth for 0.1-dB flatness VOUT = 2 VPP, G = 1 C 30 MHz
Rising slew rate (differential) VOUT = 2-V Step, G = 1, RL = 200 Ω C 490 V/μs
Falling slew rate (differential) VOUT = 2-V Step, G = 1, RL = 200 Ω C 600 V/μs
Overshoot VOUT = 2-V Step, G = 1, RL = 200 Ω C 1%
Undershoot VOUT = 2-V Step, G = 1, RL = 200 Ω C 2.6%
Rise time VOUT = 2-V Step, G = 1, RL = 200 Ω C 3.4 ns
Fall time VOUT = 2-V Step, G = 1, RL = 200 Ω C 3 ns
Settling time to 1% VOUT = 2-V Step, G = 1, RL = 200 Ω C 10 ns
HARMONIC DISTORTION
2nd harmonic f = 1 MHz, VOUT = 2 VPP, G = 1 C –85 dBc
f = 1 kHz, VOUT = 1 VRMS, G = 1(3),
differential input		 C –133 dBc
3rd harmonic f = 1 MHz, VOUT = 2 VPP, G = 1 C –91 dBc
f = 1 kHz, VOUT = 1 VRMS, G = 1(3),
differential input		 C –141 dBc
Second-order intermodulation distortion Two-tone, f1 = 2 MHz, f2 = 2.2 MHz,
VOUT = 2-VPP envelope		 C –86 dBc
Third-order intermodulation distortion Two-tone, f1 = 2 MHz, f2 = 2.2 MHz,
VOUT = 2-VPP envelope		 C –93 dBc
Input voltage noise f > 10 kHz C 4.6 nV/√Hz
Input current noise f > 100 kHz C 0.6 pA/√Hz
SNR VOUT = 5 VPP, 20 Hz to 22 kHz BW, differential input C 123 dBc
THD+N f = 1 kHz , VOUT = 5 VPP, 20 Hz to 22 kHz BW, differential input C 112 dBc
Overdrive recovery time Overdrive = ±0.5 V C 75 ns
Output balance error VOUT = 100 mV, f < 2 MHz, VIN differential C –57 dB
Closed-loop output impedance f = 1 MHz (differential) C 0.3 Ω
Channel-to-channel crosstalk (THS4522. THS4524) f = 10 kHz, measured differentially C –125 dB
DC PERFORMANCE
Open-loop voltage gain (AOL) A 100 119 dB
Input-referred offset voltage TA = +25°C A ±0.24 ±2 mV
TA = –40°C to +85°C B ±0.5 ±3.5 mV
Input offset voltage drift(2) TA = –40°C to +85°C C ±2 μV/°C
Input bias current(4) TA = +25°C B 0.7 0.9 μA
TA = –40°C to +85°C B 0.9 1.1 μA
Input bias current drift(2) TA = –40°C to +85°C B ±1.8 ±2.2 nA/°C
Input offset current TA = +25°C B ±30 ±180 nA
TA = –40°C to +85°C B ±30 ±215 nA
Input offset current drift(2) TA = –40°C to +85°C B ±100 ±600 pA/°C
INPUT
Common-mode input voltage low TA = +25°C A –0.2 –0.1 V
TA = –40°C to +85°C B –0.1 0 V
Common-mode input voltage high TA = +25°C A 3.6 3.7 V
TA = –40°C to +85°C B 3.5 3.6 V
Common-mode rejection ratio (CMRR) A 80 102 dB
Input impedance C 100∥0.7 kΩ∥pF
OUTPUT
Output voltage low TA = +25°C A 0.10 0.15 V
TA = –40°C to +85°C B 0.115 0.2 V
Output voltage high TA = +25°C A 4.7 4.75 V
TA = –40°C to +85°C B 4.65 4.7 V
Output current drive (for linear operation) RL = 50 Ω C ±55 mA
POWER SUPPLY
Specified operating voltage B 2.5 5.0 5.5 V
Quiescent operating current, per channel TA = +25°C A 0.95 1.14 1.25 mA
TA = –40°C to +85°C B 0.9 1.15 1.3 mA
Power-supply rejection ratio (±PSRR) A 80 100 dB
POWER DOWN
Enable voltage threshold Ensured on above 2.1 V A 1.6 2.1 V
Disable voltage threshold Ensured off below 0.7 V A 0.7 1.6 V
Disable pin bias current C 1 μA
Power-down quiescent current C 20 μA
Turn-on time delay Time to VOUT = 90% of final value,
VIN= 2 V, RL = 200 Ω		 B 70 ns
Turn-off time delay Time to VOUT = 10% of original value,
VIN= 2 V, RL = 200 Ω		 B 60 ns
VOCM VOLTAGE CONTROL
Small-signal bandwidth C 23 MHz
Slew rate C 55 V/μs
Gain A 0.98 0.99 1.02 V/V
Common-mode offset voltage from VOCM input Measured at VOUT with VOCM input driven, VOCM = 2.5 V ±1 V B ±5 ±9 mV
Input bias current VOCM = 2.5V ±1 V B ±20 ±25 μA
VOCM voltage range A 1 0.8 to 4.2 4 V
Input impedance C 46∥1.5 kΩ∥pF
Default output common-mode voltage offset from (VS+– VS–) / 2 Measured at VOUT with VOCM input open A ±1 ±5 mV
(1) Test levels: (A) 100% tested at 25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information.
(2) Input offset voltage drift, input bias current drift, input offset current drift, and VOCM drift are average values calculated by taking data at the maximum-range ambient-temperature end points, computing the difference, and dividing by the temperature range. Maximum drift is set by the distribution of a large sampling of devices. Drift is not specified by a test or a quality assurance (QA) sample test.
(3) Not directly measurable; calculated using noise gain of 101 as described in the Applications section, Audio Performance.
(4) Input bias current is positive out of the device.

7.7 Typical Characteristics

Table 2. Table of Graphs: VS+ – VS– = 3.3 V

FIGURE
Small-Signal Frequency Response Figure 1
Large-Signal Frequency Response Figure 2
Large- and Small-Signal Pulse Response Figure 3
Slew Rate vs VOUT Step Figure 4
Overdrive Recovery Figure 5
10-kHz Output Spectrum on AP Analyzer Figure 6
Harmonic Distortion vs Frequency Figure 7
Harmonic Distortion vs Output Voltage at 1 MHz Figure 8
Harmonic Distortion vs Gain at 1 MHz Figure 9
Harmonic Distortion vs Load at 1 MHz Figure 10
Harmonic Distortion vs VOCM at 1 MHz Figure 11
Two-Tone, Second- and Third-Order Intermodulation Distortion vs Frequency Figure 12
Single-Ended Output Voltage Swing vs Load Resistance Figure 13
Main Amplifier Differential Output Impedance vs Frequency Figure 14
Frequency Response vs CLOAD (RLOAD = 1 kΩ) Figure 15
RO vs CLOAD (RLOAD = 1 kΩ) Figure 16
Rejection Ratio vs Frequency Figure 17
THS4522, THS4524 Crosstalk (Measured Differentially) Figure 18
Turn-on Time Figure 19
Turn-off Time Figure 20
Input-Referred Voltage Noise and Current Noise Spectral Density Figure 21
Main Amplifier Differential Open-Loop Gain and Phase Figure 22
Output Balance Error vs Frequency Figure 23
VOCM Small-Signal Frequency Response Figure 24
VOCM Large-Signal Frequency Response Figure 25
VOCM Input Impedance vs Frequency Figure 26

Table 3. Table of Graphs: VS+ – VS– = 5 V

FIGURE
Small-Signal Frequency Response Figure 27
Large-Signal Frequency Response Figure 28
Large- and Small-Signal Pulse Response Figure 29
Slew Rate vs VOUT Step Figure 30
Overdrive Recovery Figure 31
10-kHz Output Spectrum on AP Analyzer Figure 33
Harmonic Distortion vs Frequency Figure 34
Harmonic Distortion vs Output Voltage at 1 MHz Figure 35
Harmonic Distortion vs Gain at 1 MHz Figure 36
Harmonic Distortion vs Load at 1 MHz Figure 37
Harmonic Distortion vs VOCM at 1 MHz Figure 38
Two-Tone, Second- and Third-Order Intermodulation Distortion vs Frequency Figure 39
Single-Ended Output Voltage Swing vs Load Resistance Figure 40
Main Amplifier Differential Output Impedance vs Frequency Figure 41
Frequency Response vs CLOAD (RLOAD = 1 kΩ) Figure 42
RO vs CLOAD (RLOAD = 1 kΩ) Figure 43
Rejection Ratio vs Frequency Figure 44
THS4522, THS4524 Crosstalk (Measured Differentially) Figure 45
Turn-on Time Figure 46
Turn-off Time Figure 47
Input-Referred Voltage Noise and Current Noise Spectral Density Figure 48
Main Amplifier Differential Open-Loop Gain and Phase Figure 49
Output Balance Error vs Frequency Figure 50
VOCM Small-Signal Frequency Response Figure 51
VOCM Large-Signal Frequency Response Figure 52
VOCM Input Impedance vs Frequency Figure 53

7.8 Typical Characteristics: VS+ – VS– = 3.3 V

At VS+ = +3.3 V, VS– = 0 V, VOCM = open, VOUT = 2 VPP (differential), RF = 1 kΩ, RL = 1 kΩ differential, G = 1 V/V, single-ended input, differential output, and input and output referenced to midsupply, unless otherwise noted.
THS4521 THS4522 THS4524 tc_fqcy_resp_sm_3v_bos458.gifFigure 1. Small-Signal Frequency Response
THS4521 THS4522 THS4524 tc_pulse_resp_3v_bos458.gifFigure 3. Large- and Small-Signal Pulse Response
THS4521 THS4522 THS4524 tc_overdrive_3v_bos458.gifFigure 5. Overdrive Recovery
THS4521 THS4522 THS4524 tc_distortion_fqcy_3v_bos458.gifFigure 7. Harmonic Distortion vs Frequency
THS4521 THS4522 THS4524 tc_distortion_gain_1mhz_3v_bos458.gifFigure 9. Harmonic Distortion vs Gain at 1 MHz
THS4521 THS4522 THS4524 tc_distortion_vocm_1mhz_3v_bos458.gifFigure 11. Harmonic Distortion vs VOCM at 1 MHz
THS4521 THS4522 THS4524 tc_vout_swing_load_se_3v_bos458.gifFigure 13. Single-Ended Output Voltage Swing vs Load Resistance
THS4521 THS4522 THS4524 tc_fqcy_resp_cload_3v_bos458.gifFigure 15. Frequency Response vs CLOAD RLOAD = 1 kΩ
THS4521 THS4522 THS4524 tc_cm_ps_rr_3v_bos458.gifFigure 17. Rejection Ratio vs Frequency
THS4521 THS4522 THS4524 tc_turn-on_3v_bos458.gifFigure 19. Turn-On Time
THS4521 THS4522 THS4524 tc_vir_isd_bos458.gifFigure 21. Input-Referred Voltage and Current Noise Spectral Density
THS4521 THS4522 THS4524 tc_output_error_fqcy_3v_bos458.gifFigure 23. Output Balance Error vs Frequency
THS4521 THS4522 THS4524 tc_vocm_large_pulse_3v_bos458.gifFigure 25. VOCM Large-Signal Pulse Response
THS4521 THS4522 THS4524 tc_fqcy_resp_lg_3v_bos458.gifFigure 2. Large-Signal Frequency Response
THS4521 THS4522 THS4524 tc_slew_rate_vout_diff_3v_bos458.gifFigure 4. Slew Rate vs VOUT
THS4521 THS4522 THS4524 tc_10khz_spectrum_3v_bos458.gifFigure 6. 10-kHz Output Spectrum On AP Analyzer
THS4521 THS4522 THS4524 tc_distortion_vout_1mhz_3v_bos458.gifFigure 8. Harmonic Distortion vs VOUT at 1 MHz
THS4521 THS4522 THS4524 tc_distortion_load_1mhz_3v_bos458.gifFigure 10. Harmonic Distortion vs Load at 1 MHz
THS4521 THS4522 THS4524 tc_2tone_imd_fqcy_3v_bos458.gifFigure 12. Two-Tone Intermodulation Distortion vs Frequency
THS4521 THS4522 THS4524 tc_vocm_input_imped02_3v_bos458.gifFigure 14. Main Amplifier Differential Output Impedance vs Frequency
THS4521 THS4522 THS4524 tc_riso_cload_3v_bos458.gifFigure 16. RO vs CLOAD RLOAD = 1 kΩ
THS4521 THS4522 THS4524 tc_xtalk_3v_bos458.gifFigure 18. THS4522, THS4524 Crosstalk (Differential Measurement)
THS4521 THS4522 THS4524 tc_turn-off_3v_bos458.gifFigure 20. Turn-Off Time
THS4521 THS4522 THS4524 tc_open_loop_gain_phase_3v_bos348.gifFigure 22. Main Amplifier Differential Open-Loop Gain and Phase
THS4521 THS4522 THS4524 tc_vocm_sm_fqcy_3v_bos458.gifFigure 24. VOCM Small-Signal Frequency Response
THS4521 THS4522 THS4524 tc_vocm_input_impd_fqcy_3v_bos458.gifFigure 26. VOCM Input Impedance vs Frequency

7.9 Typical Characteristics: 5 V

At VS+ = +5 V, VS– = 0 V, VOCM = open, VOUT = 2 VPP (differential), RF = 1 kΩ, RL = 1 kΩ differential, G = 1 V/V, single-ended input, differential output, and input and output referenced to midsupply, unless otherwise noted.
THS4521 THS4522 THS4524 tc_fqcy_resp_sm_5v_bos458.gifFigure 27. Small-Signal Frequency Response
THS4521 THS4522 THS4524 tc_pulse_resp_5v_bos458.gifFigure 29. Large- and Small-Signal Pulse Response
THS4521 THS4522 THS4524 tc_overdrive_5v_bos458.gifFigure 31. Overdrive Recovery
THS4521 THS4522 THS4524 tc_10khz_spectrum_8vpp_5v_bos458.gifFigure 33. 10-kHz Output Spectrum On AP Analyzer at
VOUT = 8 VPP
THS4521 THS4522 THS4524 tc_distortion_vout_1mhz_5v_bos458.gifFigure 35. Harmonic Distortion vs VOUT at 1 MHz
THS4521 THS4522 THS4524 tc_distortion_load_1mhz_5v_bos458.gifFigure 37. Harmonic Distortion vs Load at 1 MHz
THS4521 THS4522 THS4524 tc_2tone_imd_fqcy_5v_bos458.gifFigure 39. Two-Tone Intermodulation Distortion vs Frequency
THS4521 THS4522 THS4524 tc_vocm_input_imped02_5v_bos458.gifFigure 41. Main Amplifier Differential Output Impedance vs Frequency
THS4521 THS4522 THS4524 tc_riso_cload_5v_bos458.gifFigure 43. RO vs CLOAD RLOAD = 1 kΩ
THS4521 THS4522 THS4524 tc_xtalk_5v_bos458.gifFigure 45. THS4522, THS4524 Crosstalk (Measured Differentially)
THS4521 THS4522 THS4524 tc_turn-off_5v_bos458.gifFigure 47. Turn-Off Time
THS4521 THS4522 THS4524 tc_open_loop_gain_phase_5v_bos348.gifFigure 49. Main Amplifier Differential Open-Loop Gain and Phase
THS4521 THS4522 THS4524 tc_vocm_sm_fqcy_5v_bos458.gifFigure 51. VOCM Small-Signal Frequency Response
THS4521 THS4522 THS4524 tc_vocm_input_impd_fqcy_5v_bos458.gifFigure 53. VOCM Input Impedance vs Frequency
THS4521 THS4522 THS4524 tc_fqcy_resp_lg_5v_bos458.gifFigure 28. Large-Signal Frequency Response
THS4521 THS4522 THS4524 tc_slew_rate_vout_diff_5v_bos458.gifFigure 30. Slew Rate vs VOUT
THS4521 THS4522 THS4524 D000_Revised_Graph_32_SBOS458.gifFigure 32. Harmonic Distortion vs Frequency Below 1 MHz
THS4521 THS4522 THS4524 tc_distortion_fqcy_5v_bos458.gifFigure 34. Harmonic Distortion vs Frequency
THS4521 THS4522 THS4524 tc_distortion_gain_1mhz_5v_bos458.gifFigure 36. Harmonic Distortion vs Gain at 1 MHz
THS4521 THS4522 THS4524 tc_distortion_vocm_1mhz_5v_bos458.gifFigure 38. Harmonic Distortion vs VOCM at 1 MHz
THS4521 THS4522 THS4524 tc_vout_swing_load_se_5v_bos458.gifFigure 40. Single-Ended Output Voltage Swing vs Differential Load Resistance
THS4521 THS4522 THS4524 tc_fqcy_resp_cload_5v_bos458.gifFigure 42. Frequency Response vs CLOAD RLOAD = 1 kΩ
THS4521 THS4522 THS4524 tc_cm_ps_rr_5v_bos458.gifFigure 44. Rejection Ratio vs Frequency
THS4521 THS4522 THS4524 tc_turn-on_5v_bos458.gifFigure 46. Turn-On Time
THS4521 THS4522 THS4524 tc_vir_isd_bos458.gifFigure 48. Input-Referred Voltage and Current Noise Spectral Density
THS4521 THS4522 THS4524 tc_output_error_fqcy_5v_bos458.gifFigure 50. Output Balance Error vs Frequency
THS4521 THS4522 THS4524 tc_vocm_large_pulse_5v_bos458.gifFigure 52. VOCM Large-Signal Pulse Response