UCC28180 8-Pin Continuous Conduction Mode (CCM) PFC Controller | TI.com

UCC28180 (ACTIVE)

8-Pin Continuous Conduction Mode (CCM) PFC Controller

8-Pin Continuous Conduction Mode (CCM) PFC Controller - UCC28180
 

Description

The UCC28180 is a flexible and easy-to-use, 8-pin, active Power-Factor Correction (PFC) controller that operates under Continuous Conduction Mode (CCM) to achieve high Power Factor, low current distortion and excellent voltage regulation of boost pre-regulators in AC - DC front-ends. The controller is suitable for universal AC input systems operating in 100-W to few-kW range with the switching frequency programmable between 18 kHz to 250 kHz, to conveniently support both power MOSFET and IGBT switches. An integrated 1.5-A and 2-A (SRC-SNK) peak gate drive output, clamped internally at 15.2 V (typical), enables fast turn-on, turn-off, and easy management of the external power switch without the need for buffer circuits.

Low-distortion wave shaping of the input current using average current mode control is achieved without input line sensing, reducing the external component count. In addition, the controller features reduced current sense thresholds to facilitate the use of small-value shunt resistors for reduced power dissipation, especially important in high-power systems. To enable low current distortion, the controller also features trimmed internal current loop regulation circuits for eliminating associated inaccuracies.

Simple external networks allow for flexible compensation of the current and voltage control loops. In addition, UCC28180 offers an enhanced dynamic response circuit that is based on the voltage feedback signal to deliver improved response under fast load transients, both for output overvoltage and undervoltage conditions. An unique VCOMP discharge circuit provided in UCC28180 is activated whenever the voltage feedback signal exceeds VOVP_L thus allowing a chance for the control loop to stabilize quickly and avoid encountering the overvoltage protection function when PWM shutoff can often cause audible noise. Controlled soft start gradually regulates the input current during start-up and reduces stress on the power switches. Numerous system-level protection features available in the controller include VCC UVLO, peak current limit, soft overcurrent, output open-loop detection, output overvoltage protection and open-pin detection (VISNS). A trimmed internal reference provides accurate protection thresholds and regulation set-point. The user can control low-power standby mode by pulling the VSENSE pin below 0.82 V.

Features

  • 8-Pin Solution (No AC Line Sensing Needed)
  • Wide Range Programmable Switching Frequency (18 kHz to 250 kHz for MOSFET and IGBT-based PFC Converters)
  • Trimmed Current Loop Circuits for Low iTHD
  • Reduced Current Sense Threshold (Minimizes Power Dissipation in Shunt)
  • Average Current-Mode Control
  • Soft Over Current and Cycle-by-Cycle Peak Current Limit Protection
  • Output Overvoltage Protection With Hysteresis Recovery
  • Audible Noise Minimization Circuitry
  • Open Loop Detection
  • Enhance Dynamic Response During Output Overvoltage and Undervoltage Conditions
  • Maximum Duty Cycle of 96% (Typical)
  • Burst Mode for No Load Regulation
  • VCC UVLO, Low ICC Start-Up (< 75 µA)

View more

Parametrics Compare all products in Power Factor Correction

 
Device Type
Control Method
UVLO Thresholds On/Off (V)
Operating Supply (Max) (V)
Operating Supply Current (mA)
Pin/Package
Operating Temperature Range (C)
Rating
Features
UCC28180 UCC28019A
Single-phase PFC     Single-phase PFC    
CCM     CCM    
11.4/9.7     10.5/9.5    
21     21    
7     7.5    
8SOIC     8PDIP
8SOIC    
  -40 to 125    
Catalog     Catalog    
Audible noise minimization circuitry
Burst mode for no load regualtion
No AC line sensing
Programable switching frequency    
< 150W Applications
> 750W Applications
Average Current Mode
Enable
OVP    
View more

WEBENCH® Designer UCC28180

AC Frequency  60 Hz  50 Hz
  Min   Max Range
VinRMS  V 85.0 to 265.0V
Vout  V 130 to 400V
Iout  A ≤ 23A
Ambient Temp  °C -40 to 85°C