SPRS982H December   2016  – December 2019 AM5746 , AM5748 , AM5749

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagram
    2. 4.2 Pin Attributes
    3. 4.3 Signal Descriptions
      1. 4.3.1  VIP
      2. 4.3.2  DSS
      3. 4.3.3  HDMI
      4. 4.3.4  EMIF
      5. 4.3.5  GPMC
      6. 4.3.6  Timer
      7. 4.3.7  I2C
      8. 4.3.8  HDQ1W
      9. 4.3.9  UART
      10. 4.3.10 McSPI
      11. 4.3.11 QSPI
      12. 4.3.12 McASP
      13. 4.3.13 USB
      14. 4.3.14 SATA
      15. 4.3.15 PCIe
      16. 4.3.16 DCAN and MCAN
      17. 4.3.17 GMAC_SW
      18. 4.3.18 MLB
      19. 4.3.19 eMMC/SD/SDIO
      20. 4.3.20 GPIO
      21. 4.3.21 KBD
      22. 4.3.22 PWM
      23. 4.3.23 PRU-ICSS
      24. 4.3.24 Test Interfaces
      25. 4.3.25 System and Miscellaneous
        1. 4.3.25.1 Sysboot
        2. 4.3.25.2 PRCM
        3. 4.3.25.3 RTCSS
        4. 4.3.25.4 SDMA
        5. 4.3.25.5 INTC
        6. 4.3.25.6 Observability
        7. 4.3.25.7 Power Supplies
    4. 4.4 Pin Multiplexing
    5. 4.5 Connections for Unused Pins
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Power-On Hours (POH) Limits
      1. Table 5-1 Power-On Hours (POH) Limits
    4. 5.4  Recommended Operating Conditions
    5. 5.5  Operating Performance Points
      1. 5.5.1 AVS and ABB Requirements
      2. 5.5.2 Voltage And Core Clock Specifications
      3. 5.5.3 Maximum Supported Frequency
    6. 5.6  Power Consumption Summary
    7. 5.7  Electrical Characteristics
      1. Table 5-7  LVCMOS DDR DC Electrical Characteristics
      2. Table 5-8  Dual Voltage LVCMOS I2C DC Electrical Characteristics
      3. Table 5-9  IQ1833 Buffers DC Electrical Characteristics
      4. Table 5-10 IHHV1833 Buffers DC Electrical Characteristics
      5. Table 5-11 LVCMOS OSC Buffers DC Electrical Characteristics
      6. Table 5-12 BC1833IHHV Buffers DC Electrical Characteristics
      7. Table 5-13 Dual Voltage SDIO1833 DC Electrical Characteristics
      8. Table 5-14 Dual Voltage LVCMOS DC Electrical Characteristics
      9. 5.7.1      HDMIPHY DC Electrical Characteristics
      10. 5.7.2      USBPHY DC Electrical Characteristics
      11. 5.7.3      SATAPHY DC Electrical Characteristics
      12. 5.7.4      PCIEPHY DC Electrical Characteristics
    8. 5.8  VPP Specifications for One-Time Programmable (OTP) eFuses
      1. Table 5-15 Recommended Operating Conditions for OTP eFuse Programming
      2. 5.8.1      Hardware Requirements
      3. 5.8.2      Programming Sequence
      4. 5.8.3      Impact to Your Hardware Warranty
    9. 5.9  Thermal Characteristics
      1. 5.9.1 Package Thermal Characteristics
    10. 5.10 Timing Requirements and Switching Characteristics
      1. 5.10.1 Timing Parameters and Information
        1. 5.10.1.1 Parameter Information
          1. 5.10.1.1.1 1.8V and 3.3V Signal Transition Levels
          2. 5.10.1.1.2 1.8V and 3.3V Signal Transition Rates
          3. 5.10.1.1.3 Timing Parameters and Board Routing Analysis
      2. 5.10.2 Interface Clock Specifications
        1. 5.10.2.1 Interface Clock Terminology
        2. 5.10.2.2 Interface Clock Frequency
      3. 5.10.3 Power Supply Sequences
      4. 5.10.4 Clock Specifications
        1. 5.10.4.1 Input Clocks / Oscillators
          1. 5.10.4.1.1 OSC0 External Crystal
          2. 5.10.4.1.2 OSC0 Input Clock
          3. 5.10.4.1.3 Auxiliary Oscillator OSC1 Input Clock
            1. 5.10.4.1.3.1 OSC1 External Crystal
            2. 5.10.4.1.3.2 OSC1 Input Clock
          4. 5.10.4.1.4 RTC Oscillator Input Clock
            1. 5.10.4.1.4.1 RTC Oscillator External Crystal
            2. 5.10.4.1.4.2 RTC Oscillator Input Clock
        2. 5.10.4.2 RC On-die Oscillator Clock
        3. 5.10.4.3 Output Clocks
        4. 5.10.4.4 DPLLs, DLLs
          1. 5.10.4.4.1 DPLL Characteristics
          2. 5.10.4.4.2 DLL Characteristics
      5. 5.10.5 Recommended Clock and Control Signal Transition Behavior
      6. 5.10.6 Peripherals
        1. 5.10.6.1  Timing Test Conditions
        2. 5.10.6.2  Virtual and Manual I/O Timing Modes
        3. 5.10.6.3  VIP
        4. 5.10.6.4  DSS
        5. 5.10.6.5  HDMI
        6. 5.10.6.6  EMIF
        7. 5.10.6.7  GPMC
          1. 5.10.6.7.1 GPMC/NOR Flash Interface Synchronous Timing
          2. 5.10.6.7.2 GPMC/NOR Flash Interface Asynchronous Timing
          3. 5.10.6.7.3 GPMC/NAND Flash Interface Asynchronous Timing
        8. 5.10.6.8  I2C
          1. Table 5-65 Timing Requirements for I2C Input Timings
          2. Table 5-66 Timing Requirements for I2C HS-Mode (I2C3/4/5 Only)
          3. Table 5-67 Switching Characteristics Over Recommended Operating Conditions for I2C Output Timings
        9. 5.10.6.9  HDQ1W
          1. 5.10.6.9.1 HDQ / 1-Wire — HDQ Mode
          2. 5.10.6.9.2 HDQ/1-Wire—1-Wire Mode
        10. 5.10.6.10 UART
          1. Table 5-72 Timing Requirements for UART
          2. Table 5-73 Switching Characteristics Over Recommended Operating Conditions for UART
        11. 5.10.6.11 McSPI
        12. 5.10.6.12 QSPI
        13. 5.10.6.13 McASP
          1. Table 5-80 Timing Requirements for McASP1
          2. Table 5-81 Timing Requirements for McASP2
          3. Table 5-82 Timing Requirements for McASP3/4/5/6/7/8
          4. Table 5-83 Switching Characteristics Over Recommended Operating Conditions for McASP1
          5. Table 5-84 Switching Characteristics Over Recommended Operating Conditions for McASP2
          6. Table 5-85 Switching Characteristics Over Recommended Operating Conditions for McASP3/4/5/6/7/8
        14. 5.10.6.14 USB
          1. 5.10.6.14.1 USB1 DRD PHY
          2. 5.10.6.14.2 USB2 PHY
        15. 5.10.6.15 SATA
        16. 5.10.6.16 PCIe
        17. 5.10.6.17 CAN
          1. 5.10.6.17.1 DCAN
          2. 5.10.6.17.2 MCAN-FD
          3. Table 5-97  Timing Requirements for CANx Receive
          4. Table 5-98  Switching Characteristics Over Recommended Operating Conditions for CANx Transmit
        18. 5.10.6.18 GMAC_SW
          1. 5.10.6.18.1 GMAC MII Timings
            1. Table 5-99  Timing Requirements for miin_rxclk - MII Operation
            2. Table 5-100 Timing Requirements for miin_txclk - MII Operation
            3. Table 5-101 Timing Requirements for GMAC MIIn Receive 10/100 Mbit/s
            4. Table 5-102 Switching Characteristics Over Recommended Operating Conditions for GMAC MIIn Transmit 10/100 Mbits/s
          2. 5.10.6.18.2 GMAC MDIO Interface Timings
          3. 5.10.6.18.3 GMAC RMII Timings
            1. Table 5-107 Timing Requirements for GMAC REF_CLK - RMII Operation
            2. Table 5-108 Timing Requirements for GMAC RMIIn Receive
            3. Table 5-109 Switching Characteristics Over Recommended Operating Conditions for GMAC REF_CLK - RMII Operation
            4. Table 5-110 Switching Characteristics Over Recommended Operating Conditions for GMAC RMIIn Transmit 10/100 Mbits/s
          4. 5.10.6.18.4 GMAC RGMII Timings
            1. Table 5-114 Timing Requirements for rgmiin_rxc - RGMIIn Operation
            2. Table 5-115 Timing Requirements for GMAC RGMIIn Input Receive for 10/100/1000 Mbps
            3. Table 5-116 Switching Characteristics Over Recommended Operating Conditions for rgmiin_txctl - RGMIIn Operation for 10/100/1000 Mbit/s
            4. Table 5-117 Switching Characteristics for GMAC RGMIIn Output Transmit for 10/100/1000 Mbps
        19. 5.10.6.19 eMMC/SD/SDIO
          1. 5.10.6.19.1 MMC1—SD Card Interface
            1. 5.10.6.19.1.1 Default speed, 4-bit data, SDR, half-cycle
            2. 5.10.6.19.1.2 High speed, 4-bit data, SDR, half-cycle
            3. 5.10.6.19.1.3 SDR12, 4-bit data, half-cycle
            4. 5.10.6.19.1.4 SDR25, 4-bit data, half-cycle
            5. 5.10.6.19.1.5 UHS-I SDR50, 4-bit data, half-cycle
            6. 5.10.6.19.1.6 UHS-I SDR104, 4-bit data, half-cycle
            7. 5.10.6.19.1.7 UHS-I DDR50, 4-bit data
          2. 5.10.6.19.2 MMC2 — eMMC
            1. 5.10.6.19.2.1 Standard JC64 SDR, 8-bit data, half cycle
            2. 5.10.6.19.2.2 High Speed JC64 SDR, 8-bit data, half cycle
            3. 5.10.6.19.2.3 High Speed HS200 JC64 SDR, 8-bit data, half cycle
            4. 5.10.6.19.2.4 High Speed JC64 DDR, 8-bit data
          3. 5.10.6.19.3 MMC3 and MMC4—SDIO/SD
            1. 5.10.6.19.3.1 MMC3 and MMC4, SD Default Speed
            2. 5.10.6.19.3.2 MMC3 and MMC4, SD High Speed
            3. 5.10.6.19.3.3 MMC3 and MMC4, SD and SDIO SDR12 Mode
            4. 5.10.6.19.3.4 MMC3 and MMC4, SD SDR25 Mode
            5. 5.10.6.19.3.5 MMC3 SDIO High Speed UHS-I SDR50 Mode, Half Cycle
        20. 5.10.6.20 PRU-ICSS
          1. 5.10.6.20.1 Programmable Real-Time Unit (PRU-ICSS PRU)
            1. 5.10.6.20.1.1 PRU-ICSS PRU Direct Input/Output Mode Electrical Data and Timing
              1. Table 5-166 PRU-ICSS PRU Timing Requirements - Direct Input Mode
              2. Table 5-167 PRU-ICSS PRU Switching Requirements – Direct Output Mode
            2. 5.10.6.20.1.2 PRU-ICSS PRU Parallel Capture Mode Electrical Data and Timing
              1. Table 5-168 PRU-ICSS PRU Timing Requirements - Parallel Capture Mode
            3. 5.10.6.20.1.3 PRU-ICSS PRU Shift Mode Electrical Data and Timing
              1. Table 5-169 PRU-ICSS PRU Timing Requirements – Shift In Mode
              2. Table 5-170 PRU-ICSS PRU Switching Requirements - Shift Out Mode
            4. 5.10.6.20.1.4 PRU-ICSS PRU Sigma Delta and EnDAT Modes
              1. Table 5-171 PRU-ICSS PRU Timing Requirements - Sigma Delta Mode
              2. Table 5-172 PRU-ICSS PRU Timing Requirements - EnDAT Mode
              3. Table 5-173 PRU-ICSS PRU Switching Requirements - EnDAT Mode
          2. 5.10.6.20.2 PRU-ICSS EtherCAT (PRU-ICSS ECAT)
            1. 5.10.6.20.2.1 PRU-ICSS ECAT Electrical Data and Timing
              1. Table 5-174 PRU-ICSS ECAT Timing Requirements – Input Validated With LATCH_IN
              2. Table 5-175 PRU-ICSS ECAT Timing Requirements – Input Validated With SYNCx
              3. Table 5-176 PRU-ICSS ECAT Timing Requirements – Input Validated With Start of Frame (SOF)
              4. Table 5-177 PRU-ICSS ECAT Timing Requirements - LATCHx_IN
              5. Table 5-178 PRU-ICSS ECAT Switching Requirements - Digital IOs
          3. 5.10.6.20.3 PRU-ICSS MII_RT and Switch
            1. 5.10.6.20.3.1 PRU-ICSS MDIO Electrical Data and Timing
              1. Table 5-179 PRU-ICSS MDIO Timing Requirements – MDIO_DATA
              2. Table 5-180 PRU-ICSS MDIO Switching Characteristics - MDIO_CLK
              3. Table 5-181 PRU-ICSS MDIO Switching Characteristics – MDIO_DATA
            2. 5.10.6.20.3.2 PRU-ICSS MII_RT Electrical Data and Timing
              1. Table 5-182 PRU-ICSS MII_RT Timing Requirements – MII[x]_RXCLK
              2. Table 5-183 PRU-ICSS MII_RT Timing Requirements - MII[x]_TXCLK
              3. Table 5-184 PRU-ICSS MII_RT Timing Requirements - MII_RXD[3:0], MII_RXDV, and MII_RXER
              4. Table 5-185 PRU-ICSS MII_RT Switching Characteristics - MII_TXD[3:0] and MII_TXEN
          4. 5.10.6.20.4 PRU-ICSS Universal Asynchronous Receiver Transmitter (PRU-ICSS UART)
            1. Table 5-186 Timing Requirements for PRU-ICSS UART Receive
            2. Table 5-187 Switching Characteristics Over Recommended Operating Conditions for PRU-ICSS UART Transmit
          5. 5.10.6.20.5 PRU-ICSS IOSETs
          6. 5.10.6.20.6 PRU-ICSS Manual Functional Mapping
        21. 5.10.6.21 System and Miscellaneous interfaces
      7. 5.10.7 Emulation and Debug Subsystem
        1. 5.10.7.1 JTAG
          1. 5.10.7.1.1 JTAG Electrical Data/Timing
            1. Table 5-210 Timing Requirements for IEEE 1149.1 JTAG
            2. Table 5-211 Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG
            3. Table 5-212 Timing Requirements for IEEE 1149.1 JTAG With RTCK
            4. Table 5-213 Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG With RTCK
        2. 5.10.7.2 TPIU
          1. 5.10.7.2.1 TPIU PLL DDR Mode
  6. 6Detailed Description
    1. 6.1 Overview
    2. 6.2 Processor Subsystems
      1. 6.2.1 MPU
      2. 6.2.2 DSP Subsystem
      3. 6.2.3 IPU
      4. 6.2.4 Interrupt Controller
      5. 6.2.5 VPE
    3. 6.3 Accelerators and Coprocessors
      1. 6.3.1 IVA
      2. 6.3.2 GPU
      3. 6.3.3 PRU-ICSS
      4. 6.3.4 EVE
    4. 6.4 Other Subsystems
      1. 6.4.1 Memory Subsystem
        1. 6.4.1.1 EMIF
        2. 6.4.1.2 GPMC
        3. 6.4.1.3 ELM
        4. 6.4.1.4 OCMC
        5. 6.4.1.5 Interprocessor Communication
          1. 6.4.1.5.1 Mailbox
          2. 6.4.1.5.2 Spinlock
      2. 6.4.2 EDMA
      3. 6.4.3 Peripherals
        1. 6.4.3.1  VIP
        2. 6.4.3.2  DSS
        3. 6.4.3.3  Timers
        4. 6.4.3.4  I2C
        5. 6.4.3.5  HDQ1W
        6. 6.4.3.6  UART
          1. 6.4.3.6.1 UART Features
          2. 6.4.3.6.2 IrDA Features
          3. 6.4.3.6.3 CIR Features
        7. 6.4.3.7  McSPI
        8. 6.4.3.8  QSPI
        9. 6.4.3.9  McASP
        10. 6.4.3.10 USB
        11. 6.4.3.11 SATA
        12. 6.4.3.12 PCIe
        13. 6.4.3.13 CAN
          1. 6.4.3.13.1 DCAN
          2. 6.4.3.13.2 MCAN-FD
        14. 6.4.3.14 GMAC_SW
        15. 6.4.3.15 eMMC/SD/SDIO
        16. 6.4.3.16 GPIO
        17. 6.4.3.17 ePWM
        18. 6.4.3.18 eCAP
        19. 6.4.3.19 eQEP
      4. 6.4.4 On-Chip Debug
    5. 6.5 Identification
      1. 6.5.1 Revision Identification
      2. 6.5.2 Die Identification
      3. 6.5.3 JTAG Identification
      4. 6.5.4 ROM Code Identification
    6. 6.6 Boot Modes
      1. 6.6.1 Boot Mode List
      2. 6.6.2 Boot Mode Pin Usage
        1. 6.6.2.1 GPMC Configuration for XIP/NAND
        2. 6.6.2.2 System Clock Speed Selection
        3. 6.6.2.3 QSPI Redundant SBL Images Offset
      3. 6.6.3 Boot Mode Selection
        1. 6.6.3.1 Booting Device Order Selection
  7. 7Applications, Implementation, and Layout
    1. 7.1 Power Supply Mapping
    2. 7.2 DDR3 Board Design and Layout Guidelines
      1. 7.2.1 DDR3 General Board Layout Guidelines
      2. 7.2.2 DDR3 Board Design and Layout Guidelines
        1. 7.2.2.1  Board Designs
        2. 7.2.2.2  DDR3 EMIFs
        3. 7.2.2.3  DDR3 Device Combinations
        4. 7.2.2.4  DDR3 Interface Schematic
          1. 7.2.2.4.1 32-Bit DDR3 Interface
          2. 7.2.2.4.2 16-Bit DDR3 Interface
        5. 7.2.2.5  Compatible JEDEC DDR3 Devices
        6. 7.2.2.6  PCB Stackup
        7. 7.2.2.7  Placement
        8. 7.2.2.8  DDR3 Keepout Region
        9. 7.2.2.9  Bulk Bypass Capacitors
        10. 7.2.2.10 High Speed Bypass Capacitors
          1. 7.2.2.10.1 Return Current Bypass Capacitors
        11. 7.2.2.11 Net Classes
        12. 7.2.2.12 DDR3 Signal Termination
        13. 7.2.2.13 VREF_DDR Routing
        14. 7.2.2.14 VTT
        15. 7.2.2.15 CK and ADDR_CTRL Topologies and Routing Definition
          1. 7.2.2.15.1 Four DDR3 Devices
            1. 7.2.2.15.1.1 CK and ADDR_CTRL Topologies, Four DDR3 Devices
            2. 7.2.2.15.1.2 CK and ADDR_CTRL Routing, Four DDR3 Devices
          2. 7.2.2.15.2 Two DDR3 Devices
            1. 7.2.2.15.2.1 CK and ADDR_CTRL Topologies, Two DDR3 Devices
            2. 7.2.2.15.2.2 CK and ADDR_CTRL Routing, Two DDR3 Devices
          3. 7.2.2.15.3 One DDR3 Device
            1. 7.2.2.15.3.1 CK and ADDR_CTRL Topologies, One DDR3 Device
            2. 7.2.2.15.3.2 CK and ADDR/CTRL Routing, One DDR3 Device
        16. 7.2.2.16 Data Topologies and Routing Definition
          1. 7.2.2.16.1 DQS and DQ/DM Topologies, Any Number of Allowed DDR3 Devices
          2. 7.2.2.16.2 DQS and DQ/DM Routing, Any Number of Allowed DDR3 Devices
        17. 7.2.2.17 Routing Specification
          1. 7.2.2.17.1 CK and ADDR_CTRL Routing Specification
          2. 7.2.2.17.2 DQS and DQ Routing Specification
    3. 7.3 High Speed Differential Signal Routing Guidance
    4. 7.4 Power Distribution Network Implementation Guidance
    5. 7.5 Thermal Solution Guidance
    6. 7.6 Single-Ended Interfaces
      1. 7.6.1 General Routing Guidelines
      2. 7.6.2 QSPI Board Design and Layout Guidelines
    7. 7.7 LJCB_REFN/P Connections
    8. 7.8 Clock Routing Guidelines
      1. 7.8.1 32-kHz Oscillator Routing
      2. 7.8.2 Oscillator Ground Connection
  8. 8Device and Documentation Support
    1. 8.1 Device Nomenclature
      1. 8.1.1 Standard Package Symbolization
      2. 8.1.2 Device Naming Convention
    2. 8.2 Tools and Software
    3. 8.3 Documentation Support
    4. 8.4 Related Links
    5. 8.5 Support Resources
    6. 8.6 Trademarks
    7. 8.7 Electrostatic Discharge Caution
    8. 8.8 Glossary
  9. 9Mechanical, Packaging, and Orderable Information
    1. 9.1 Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • ABZ|760
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Power Supplies

NOTE

For more information, see the Power, Reset, and Clock Management / PRCM Subsystem Environment / External Voltage Inputs section in the device TRM.

Table 4-32 Power Supply Signal Descriptions

SIGNAL NAME DESCRIPTION TYPE BALL
vdd Core voltage domain supply PWR H13/ H14/ J17/ J18/ L7/ L8/ N10/ N13/ P11/ P12/ P13/ R11/ R16/ R19/ T13/ T16/ T19/ U8/ U9/ U13/ U16/ V8/ V16
vpp(2) eFuse power supply PWR K14
vss Ground GND A1/ A2/ A6/ A14/ A23/ A28/ B1/ D13/ D19/ E13/ E19/ F1/ F7/ G7/ G8/ G9/ H12/ J12/ J15/ J28/ K1/ K4/ K5/ K15/ K24/ K25/ L13/ L14/ M19/ N14/ N15/ N19/ N24/ N25/ P28/ R1/ R12/ R13/ R15/ R21/ T10/ T11/ T12/ T14/ T15/ T17/ T18/ T21/ U15/ U17/ U20/ U21/ V15/ V17/ W1/ W15/ W24/ W25/ W28/ AA8/ AA9/ AA10/ AA14/ AA15/ AA20/ AB14/ AB20/ AD1/ AD24/ AG1/ AH1/ AH2/ AH8/ AH20/ AH28 / AB11/ AA11 / AE19 / AD19 / AE13 / AD13 / AE10 / AD10 / U14
vdd_dspeve DSP voltage domain supply PWR J13/ K10/ K11/ K12/ K13/ L10/ L11/ L12/ M10/ M11/ M12/ M13
vdd_iva IVA voltage domain supply PWR U18/ U19/ V18/ V19
vdd_gpu GPU voltage domain supply PWR U11/ U12/ V10/ V11/ V14/ W10/ W11/ W13
vdd_mpu MPU voltage domain supply PWR K17/ K18/ L15/ L16/ L17/ L18/ L19/ M15/ M16/ M17/ M18/ N17/ N18/ P17/ P18/ R18
vdd_rtc RTC voltage domain supply PWR AB15
vdda_usb1 DPLL_USB and HS USB1 1.8V analog power supply PWR AA13
vdda_usb2 HS USB2 1.8V analog power supply PWR AB12
vdda33v_usb1 HS USB1 3.3V analog power supply. If USB1 is not used, this pin can alternatively be connected to VSS if the following requirements are met:
- The usb1_dm/usb1_dp pins are left unconnected
- The USB1 PHY is kept powered down
PWR AA12
vdda33v_usb2 HS USB2 3.3V analog power supply. If USB2 is not used, this pin can alternatively be connected to VSS if the following requirements are met:
- The usb2_dm/usb2_dp pins are left unconnected
- The USB2 PHY is kept powered down
PWR Y12
vdda_abe_per DPLL_ABE, DPLL_PER, and PER HSDIVIDER analog power supply PWR M14
vdda_ddr DPLL_DDR and DDR HSDIVIDER analog power supply PWR P16
vdda_debug DPLL_DEBUG analog power supply PWR N11
vdda_dsp_eve DPLL_DSP analog power supply PWR N12
vdda_gmac_core DPLL_CORE and CORE HSDIVIDER analog power supply PWR P15
vdda_gpu DPLL_GPU analog power supply PWR R14
vdda_hdmi PLL_HDMI and HDMI analog power supply PWR Y17
vdda_iva DPLL_IVA analog power supply PWR R17
vdda_pcie DPLL_PCIe_REF and PCIe analog power supply PWR W14
vdda_pcie0 PCIe ch0 RX/TX analog power supply PWR AA17
vdda_pcie1 PCIe ch1 RX/TX analog power supply PWR AA16
vdda_sata DPLL_SATA and SATA RX/TX analog power supply PWR V13
vdda_usb3 DPLL_USB_OTG_SS and USB3.0 RX/TX analog power supply PWR W12
vdda_video DPLL_VIDEO1 and DPLL_VIDEO2 analog power supply PWR P14
vdds_mlbp MLBP IO power supply PWR AA7/ Y7
vdda_mpu DPLL_MPU analog power supply PWR N16
vdda_osc HFOSC analog power supply PWR AE16/ AD16
vssa_osc0 OSC0 analog ground GND AF15
vssa_osc1 OSC1 analog ground GND AC14
vdda_rtc RTC bias and RTC LFOSC analog power supply PWR AB13
vdds18v 1.8V power supply PWR W17/ W18/ V21/ V22/ T8/ R8/ P8/ N8/ M8/ M9/ H17/ G18
vdds18v_ddr1 DDR1 bias power supply PWR AA18/ AA19/ Y21/ W21
vdds18v_ddr2 DDR2 bias power supply PWR P20/ P21/ N21/ J21/ J22
vdds_ddr2 DDR2 power supply (1.8V for DDR2 mode/ 1.5V for DDR3 mode / 1.35V for DDR3L mode) PWR T24/ T25/ M20/ M21/ L20/ L21/ J27/ H20/ H21/ H22/ G22/ G23/ E24
vdds_ddr1 DDR1 power supply (1.8V for DDR2 mode/ 1.5V for DDR3 mode / 1.35V for DDR3L mode) PWR AH27/ AG20/ AG28/ AD26/ AC22/ AB21/ AB22/ AB24/ AB25/ AA21/ AA22/ W16/ W27
vddshv5 Dual Voltage (1.8V or 3.3V) power supply for the RTC Power Group pins PWR V12
vddshv1 Dual Voltage (1.8V or 3.3V) power supply for the VIN2 Power Group pins PWR H8/ H9/ G4/ G5/ E3/ E5
vddshv10 Dual Voltage (1.8V or 3.3V) power supply for the GPMC Power Group pins PWR T4/ T5/ R7/ R10/ P10/ N4/ N5
vddshv11 Dual Voltage (1.8V or 3.3V) power supply for the MMC2 Power Group pins PWR K8/J8
vddshv2 Dual Voltage (1.8V or 3.3V) power supply for the VOUT Power Group pins PWR H10/ H11/ E10/ D10/ B6
vddshv3 Dual Voltage (1.8V or 3.3V) power supply for the GENERAL Power Group pins PWR H15/ H16/ H18/ H19/ G15/ E16/ E22/ D16/ D22/ B23
vddshv4 Dual Voltage (1.8V or 3.3V) power supply for the MMC4 Power Group pins PWR C24
vddshv6 Dual Voltage (1.8V or 3.3V) power supply for the VIN1 Power Group pins PWR AF5/ AE7/ AD5/ AD7
vddshv7 Dual Voltage (1.8V or 3.3V) power supply for the WIFI Power Group pins PWR AB6/ AB7
vddshv8 Dual Voltage (1.8V or 3.3V) power supply for the MMC1 Power Group pins PWR Y8/ W8
vddshv9 Dual Voltage (1.8V or 3.3V) power supply for the RGMII Power Group pins PWR W4/ W5/ U10
cap_vddram_dspeve2(1) External capacitor connection for the DSP SRAM array ldo2 output CAP J9
cap_vddram_dspeve1(1) External capacitor connection for the DSP SRAM array ldo1 output CAP J10
cap_vbbldo_mpu(1) External capacitor connection for the MPU vbb ldo output CAP J16
cap_vddram_core2(1) External capacitor connection for the Core SRAM array ldo2 output CAP J19
cap_vbbldo_dspeve(1) External capacitor connection for the DSP vbb ldo output CAP K9
cap_vddram_mpu1(1) External capacitor connection for the MPU SRAM array ldo1 output CAP K16
cap_vddram_mpu2(1) External capacitor connection for the MPU SRAM array ldo2 output CAP K19
cap_vddram_core1(1) External capacitor connection for the Core SRAM array ldo1 output CAP L9
cap_vddram_core4(1) External capacitor connection for the Core SRAM array ldo4 output CAP P19
cap_vbbldo_iva(1) External capacitor connection for the IVA vbb ldo output CAP R20
cap_vddram_iva(1) External capacitor connection for the IVA SRAM array ldo output CAP T20
cap_vddram_gpu(1) External capacitor connection for the GPU SRAM array ldo output CAP Y13
cap_vbbldo_gpu(1) External capacitor connection for the GPU vbb ldo output CAP Y14
cap_vddram_core3(1) External capacitor connection for the Core SRAM array ldo3 output CAP Y15
cap_vddram_core5(1) External capacitor connection for the Core SRAM array ldo5 output CAP Y16
  1. This pin must always be connected via a 1-µF capacitor to vss.
  2. This signal is valid only for High-Security devices. For more details, see Section 5.8, VPP Specification for One-Time Programmable (OTP) eFUSEs. For General-purpose devices do not connect any signal, test point, or board trace to this signal.