SPRS982H December   2016  – December 2019 AM5746 , AM5748 , AM5749

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagram
    2. 4.2 Pin Attributes
    3. 4.3 Signal Descriptions
      1. 4.3.1  VIP
      2. 4.3.2  DSS
      3. 4.3.3  HDMI
      4. 4.3.4  EMIF
      5. 4.3.5  GPMC
      6. 4.3.6  Timer
      7. 4.3.7  I2C
      8. 4.3.8  HDQ1W
      9. 4.3.9  UART
      10. 4.3.10 McSPI
      11. 4.3.11 QSPI
      12. 4.3.12 McASP
      13. 4.3.13 USB
      14. 4.3.14 SATA
      15. 4.3.15 PCIe
      16. 4.3.16 DCAN and MCAN
      17. 4.3.17 GMAC_SW
      18. 4.3.18 MLB
      19. 4.3.19 eMMC/SD/SDIO
      20. 4.3.20 GPIO
      21. 4.3.21 KBD
      22. 4.3.22 PWM
      23. 4.3.23 PRU-ICSS
      24. 4.3.24 Test Interfaces
      25. 4.3.25 System and Miscellaneous
        1. 4.3.25.1 Sysboot
        2. 4.3.25.2 PRCM
        3. 4.3.25.3 RTCSS
        4. 4.3.25.4 SDMA
        5. 4.3.25.5 INTC
        6. 4.3.25.6 Observability
        7. 4.3.25.7 Power Supplies
    4. 4.4 Pin Multiplexing
    5. 4.5 Connections for Unused Pins
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Power-On Hours (POH) Limits
      1. Table 5-1 Power-On Hours (POH) Limits
    4. 5.4  Recommended Operating Conditions
    5. 5.5  Operating Performance Points
      1. 5.5.1 AVS and ABB Requirements
      2. 5.5.2 Voltage And Core Clock Specifications
      3. 5.5.3 Maximum Supported Frequency
    6. 5.6  Power Consumption Summary
    7. 5.7  Electrical Characteristics
      1. Table 5-7  LVCMOS DDR DC Electrical Characteristics
      2. Table 5-8  Dual Voltage LVCMOS I2C DC Electrical Characteristics
      3. Table 5-9  IQ1833 Buffers DC Electrical Characteristics
      4. Table 5-10 IHHV1833 Buffers DC Electrical Characteristics
      5. Table 5-11 LVCMOS OSC Buffers DC Electrical Characteristics
      6. Table 5-12 BC1833IHHV Buffers DC Electrical Characteristics
      7. Table 5-13 Dual Voltage SDIO1833 DC Electrical Characteristics
      8. Table 5-14 Dual Voltage LVCMOS DC Electrical Characteristics
      9. 5.7.1      HDMIPHY DC Electrical Characteristics
      10. 5.7.2      USBPHY DC Electrical Characteristics
      11. 5.7.3      SATAPHY DC Electrical Characteristics
      12. 5.7.4      PCIEPHY DC Electrical Characteristics
    8. 5.8  VPP Specifications for One-Time Programmable (OTP) eFuses
      1. Table 5-15 Recommended Operating Conditions for OTP eFuse Programming
      2. 5.8.1      Hardware Requirements
      3. 5.8.2      Programming Sequence
      4. 5.8.3      Impact to Your Hardware Warranty
    9. 5.9  Thermal Characteristics
      1. 5.9.1 Package Thermal Characteristics
    10. 5.10 Timing Requirements and Switching Characteristics
      1. 5.10.1 Timing Parameters and Information
        1. 5.10.1.1 Parameter Information
          1. 5.10.1.1.1 1.8V and 3.3V Signal Transition Levels
          2. 5.10.1.1.2 1.8V and 3.3V Signal Transition Rates
          3. 5.10.1.1.3 Timing Parameters and Board Routing Analysis
      2. 5.10.2 Interface Clock Specifications
        1. 5.10.2.1 Interface Clock Terminology
        2. 5.10.2.2 Interface Clock Frequency
      3. 5.10.3 Power Supply Sequences
      4. 5.10.4 Clock Specifications
        1. 5.10.4.1 Input Clocks / Oscillators
          1. 5.10.4.1.1 OSC0 External Crystal
          2. 5.10.4.1.2 OSC0 Input Clock
          3. 5.10.4.1.3 Auxiliary Oscillator OSC1 Input Clock
            1. 5.10.4.1.3.1 OSC1 External Crystal
            2. 5.10.4.1.3.2 OSC1 Input Clock
          4. 5.10.4.1.4 RTC Oscillator Input Clock
            1. 5.10.4.1.4.1 RTC Oscillator External Crystal
            2. 5.10.4.1.4.2 RTC Oscillator Input Clock
        2. 5.10.4.2 RC On-die Oscillator Clock
        3. 5.10.4.3 Output Clocks
        4. 5.10.4.4 DPLLs, DLLs
          1. 5.10.4.4.1 DPLL Characteristics
          2. 5.10.4.4.2 DLL Characteristics
      5. 5.10.5 Recommended Clock and Control Signal Transition Behavior
      6. 5.10.6 Peripherals
        1. 5.10.6.1  Timing Test Conditions
        2. 5.10.6.2  Virtual and Manual I/O Timing Modes
        3. 5.10.6.3  VIP
        4. 5.10.6.4  DSS
        5. 5.10.6.5  HDMI
        6. 5.10.6.6  EMIF
        7. 5.10.6.7  GPMC
          1. 5.10.6.7.1 GPMC/NOR Flash Interface Synchronous Timing
          2. 5.10.6.7.2 GPMC/NOR Flash Interface Asynchronous Timing
          3. 5.10.6.7.3 GPMC/NAND Flash Interface Asynchronous Timing
        8. 5.10.6.8  I2C
          1. Table 5-65 Timing Requirements for I2C Input Timings
          2. Table 5-66 Timing Requirements for I2C HS-Mode (I2C3/4/5 Only)
          3. Table 5-67 Switching Characteristics Over Recommended Operating Conditions for I2C Output Timings
        9. 5.10.6.9  HDQ1W
          1. 5.10.6.9.1 HDQ / 1-Wire — HDQ Mode
          2. 5.10.6.9.2 HDQ/1-Wire—1-Wire Mode
        10. 5.10.6.10 UART
          1. Table 5-72 Timing Requirements for UART
          2. Table 5-73 Switching Characteristics Over Recommended Operating Conditions for UART
        11. 5.10.6.11 McSPI
        12. 5.10.6.12 QSPI
        13. 5.10.6.13 McASP
          1. Table 5-80 Timing Requirements for McASP1
          2. Table 5-81 Timing Requirements for McASP2
          3. Table 5-82 Timing Requirements for McASP3/4/5/6/7/8
          4. Table 5-83 Switching Characteristics Over Recommended Operating Conditions for McASP1
          5. Table 5-84 Switching Characteristics Over Recommended Operating Conditions for McASP2
          6. Table 5-85 Switching Characteristics Over Recommended Operating Conditions for McASP3/4/5/6/7/8
        14. 5.10.6.14 USB
          1. 5.10.6.14.1 USB1 DRD PHY
          2. 5.10.6.14.2 USB2 PHY
        15. 5.10.6.15 SATA
        16. 5.10.6.16 PCIe
        17. 5.10.6.17 CAN
          1. 5.10.6.17.1 DCAN
          2. 5.10.6.17.2 MCAN-FD
          3. Table 5-97  Timing Requirements for CANx Receive
          4. Table 5-98  Switching Characteristics Over Recommended Operating Conditions for CANx Transmit
        18. 5.10.6.18 GMAC_SW
          1. 5.10.6.18.1 GMAC MII Timings
            1. Table 5-99  Timing Requirements for miin_rxclk - MII Operation
            2. Table 5-100 Timing Requirements for miin_txclk - MII Operation
            3. Table 5-101 Timing Requirements for GMAC MIIn Receive 10/100 Mbit/s
            4. Table 5-102 Switching Characteristics Over Recommended Operating Conditions for GMAC MIIn Transmit 10/100 Mbits/s
          2. 5.10.6.18.2 GMAC MDIO Interface Timings
          3. 5.10.6.18.3 GMAC RMII Timings
            1. Table 5-107 Timing Requirements for GMAC REF_CLK - RMII Operation
            2. Table 5-108 Timing Requirements for GMAC RMIIn Receive
            3. Table 5-109 Switching Characteristics Over Recommended Operating Conditions for GMAC REF_CLK - RMII Operation
            4. Table 5-110 Switching Characteristics Over Recommended Operating Conditions for GMAC RMIIn Transmit 10/100 Mbits/s
          4. 5.10.6.18.4 GMAC RGMII Timings
            1. Table 5-114 Timing Requirements for rgmiin_rxc - RGMIIn Operation
            2. Table 5-115 Timing Requirements for GMAC RGMIIn Input Receive for 10/100/1000 Mbps
            3. Table 5-116 Switching Characteristics Over Recommended Operating Conditions for rgmiin_txctl - RGMIIn Operation for 10/100/1000 Mbit/s
            4. Table 5-117 Switching Characteristics for GMAC RGMIIn Output Transmit for 10/100/1000 Mbps
        19. 5.10.6.19 eMMC/SD/SDIO
          1. 5.10.6.19.1 MMC1—SD Card Interface
            1. 5.10.6.19.1.1 Default speed, 4-bit data, SDR, half-cycle
            2. 5.10.6.19.1.2 High speed, 4-bit data, SDR, half-cycle
            3. 5.10.6.19.1.3 SDR12, 4-bit data, half-cycle
            4. 5.10.6.19.1.4 SDR25, 4-bit data, half-cycle
            5. 5.10.6.19.1.5 UHS-I SDR50, 4-bit data, half-cycle
            6. 5.10.6.19.1.6 UHS-I SDR104, 4-bit data, half-cycle
            7. 5.10.6.19.1.7 UHS-I DDR50, 4-bit data
          2. 5.10.6.19.2 MMC2 — eMMC
            1. 5.10.6.19.2.1 Standard JC64 SDR, 8-bit data, half cycle
            2. 5.10.6.19.2.2 High Speed JC64 SDR, 8-bit data, half cycle
            3. 5.10.6.19.2.3 High Speed HS200 JC64 SDR, 8-bit data, half cycle
            4. 5.10.6.19.2.4 High Speed JC64 DDR, 8-bit data
          3. 5.10.6.19.3 MMC3 and MMC4—SDIO/SD
            1. 5.10.6.19.3.1 MMC3 and MMC4, SD Default Speed
            2. 5.10.6.19.3.2 MMC3 and MMC4, SD High Speed
            3. 5.10.6.19.3.3 MMC3 and MMC4, SD and SDIO SDR12 Mode
            4. 5.10.6.19.3.4 MMC3 and MMC4, SD SDR25 Mode
            5. 5.10.6.19.3.5 MMC3 SDIO High Speed UHS-I SDR50 Mode, Half Cycle
        20. 5.10.6.20 PRU-ICSS
          1. 5.10.6.20.1 Programmable Real-Time Unit (PRU-ICSS PRU)
            1. 5.10.6.20.1.1 PRU-ICSS PRU Direct Input/Output Mode Electrical Data and Timing
              1. Table 5-166 PRU-ICSS PRU Timing Requirements - Direct Input Mode
              2. Table 5-167 PRU-ICSS PRU Switching Requirements – Direct Output Mode
            2. 5.10.6.20.1.2 PRU-ICSS PRU Parallel Capture Mode Electrical Data and Timing
              1. Table 5-168 PRU-ICSS PRU Timing Requirements - Parallel Capture Mode
            3. 5.10.6.20.1.3 PRU-ICSS PRU Shift Mode Electrical Data and Timing
              1. Table 5-169 PRU-ICSS PRU Timing Requirements – Shift In Mode
              2. Table 5-170 PRU-ICSS PRU Switching Requirements - Shift Out Mode
            4. 5.10.6.20.1.4 PRU-ICSS PRU Sigma Delta and EnDAT Modes
              1. Table 5-171 PRU-ICSS PRU Timing Requirements - Sigma Delta Mode
              2. Table 5-172 PRU-ICSS PRU Timing Requirements - EnDAT Mode
              3. Table 5-173 PRU-ICSS PRU Switching Requirements - EnDAT Mode
          2. 5.10.6.20.2 PRU-ICSS EtherCAT (PRU-ICSS ECAT)
            1. 5.10.6.20.2.1 PRU-ICSS ECAT Electrical Data and Timing
              1. Table 5-174 PRU-ICSS ECAT Timing Requirements – Input Validated With LATCH_IN
              2. Table 5-175 PRU-ICSS ECAT Timing Requirements – Input Validated With SYNCx
              3. Table 5-176 PRU-ICSS ECAT Timing Requirements – Input Validated With Start of Frame (SOF)
              4. Table 5-177 PRU-ICSS ECAT Timing Requirements - LATCHx_IN
              5. Table 5-178 PRU-ICSS ECAT Switching Requirements - Digital IOs
          3. 5.10.6.20.3 PRU-ICSS MII_RT and Switch
            1. 5.10.6.20.3.1 PRU-ICSS MDIO Electrical Data and Timing
              1. Table 5-179 PRU-ICSS MDIO Timing Requirements – MDIO_DATA
              2. Table 5-180 PRU-ICSS MDIO Switching Characteristics - MDIO_CLK
              3. Table 5-181 PRU-ICSS MDIO Switching Characteristics – MDIO_DATA
            2. 5.10.6.20.3.2 PRU-ICSS MII_RT Electrical Data and Timing
              1. Table 5-182 PRU-ICSS MII_RT Timing Requirements – MII[x]_RXCLK
              2. Table 5-183 PRU-ICSS MII_RT Timing Requirements - MII[x]_TXCLK
              3. Table 5-184 PRU-ICSS MII_RT Timing Requirements - MII_RXD[3:0], MII_RXDV, and MII_RXER
              4. Table 5-185 PRU-ICSS MII_RT Switching Characteristics - MII_TXD[3:0] and MII_TXEN
          4. 5.10.6.20.4 PRU-ICSS Universal Asynchronous Receiver Transmitter (PRU-ICSS UART)
            1. Table 5-186 Timing Requirements for PRU-ICSS UART Receive
            2. Table 5-187 Switching Characteristics Over Recommended Operating Conditions for PRU-ICSS UART Transmit
          5. 5.10.6.20.5 PRU-ICSS IOSETs
          6. 5.10.6.20.6 PRU-ICSS Manual Functional Mapping
        21. 5.10.6.21 System and Miscellaneous interfaces
      7. 5.10.7 Emulation and Debug Subsystem
        1. 5.10.7.1 JTAG
          1. 5.10.7.1.1 JTAG Electrical Data/Timing
            1. Table 5-210 Timing Requirements for IEEE 1149.1 JTAG
            2. Table 5-211 Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG
            3. Table 5-212 Timing Requirements for IEEE 1149.1 JTAG With RTCK
            4. Table 5-213 Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG With RTCK
        2. 5.10.7.2 TPIU
          1. 5.10.7.2.1 TPIU PLL DDR Mode
  6. 6Detailed Description
    1. 6.1 Overview
    2. 6.2 Processor Subsystems
      1. 6.2.1 MPU
      2. 6.2.2 DSP Subsystem
      3. 6.2.3 IPU
      4. 6.2.4 Interrupt Controller
      5. 6.2.5 VPE
    3. 6.3 Accelerators and Coprocessors
      1. 6.3.1 IVA
      2. 6.3.2 GPU
      3. 6.3.3 PRU-ICSS
      4. 6.3.4 EVE
    4. 6.4 Other Subsystems
      1. 6.4.1 Memory Subsystem
        1. 6.4.1.1 EMIF
        2. 6.4.1.2 GPMC
        3. 6.4.1.3 ELM
        4. 6.4.1.4 OCMC
        5. 6.4.1.5 Interprocessor Communication
          1. 6.4.1.5.1 Mailbox
          2. 6.4.1.5.2 Spinlock
      2. 6.4.2 EDMA
      3. 6.4.3 Peripherals
        1. 6.4.3.1  VIP
        2. 6.4.3.2  DSS
        3. 6.4.3.3  Timers
        4. 6.4.3.4  I2C
        5. 6.4.3.5  HDQ1W
        6. 6.4.3.6  UART
          1. 6.4.3.6.1 UART Features
          2. 6.4.3.6.2 IrDA Features
          3. 6.4.3.6.3 CIR Features
        7. 6.4.3.7  McSPI
        8. 6.4.3.8  QSPI
        9. 6.4.3.9  McASP
        10. 6.4.3.10 USB
        11. 6.4.3.11 SATA
        12. 6.4.3.12 PCIe
        13. 6.4.3.13 CAN
          1. 6.4.3.13.1 DCAN
          2. 6.4.3.13.2 MCAN-FD
        14. 6.4.3.14 GMAC_SW
        15. 6.4.3.15 eMMC/SD/SDIO
        16. 6.4.3.16 GPIO
        17. 6.4.3.17 ePWM
        18. 6.4.3.18 eCAP
        19. 6.4.3.19 eQEP
      4. 6.4.4 On-Chip Debug
    5. 6.5 Identification
      1. 6.5.1 Revision Identification
      2. 6.5.2 Die Identification
      3. 6.5.3 JTAG Identification
      4. 6.5.4 ROM Code Identification
    6. 6.6 Boot Modes
      1. 6.6.1 Boot Mode List
      2. 6.6.2 Boot Mode Pin Usage
        1. 6.6.2.1 GPMC Configuration for XIP/NAND
        2. 6.6.2.2 System Clock Speed Selection
        3. 6.6.2.3 QSPI Redundant SBL Images Offset
      3. 6.6.3 Boot Mode Selection
        1. 6.6.3.1 Booting Device Order Selection
  7. 7Applications, Implementation, and Layout
    1. 7.1 Power Supply Mapping
    2. 7.2 DDR3 Board Design and Layout Guidelines
      1. 7.2.1 DDR3 General Board Layout Guidelines
      2. 7.2.2 DDR3 Board Design and Layout Guidelines
        1. 7.2.2.1  Board Designs
        2. 7.2.2.2  DDR3 EMIFs
        3. 7.2.2.3  DDR3 Device Combinations
        4. 7.2.2.4  DDR3 Interface Schematic
          1. 7.2.2.4.1 32-Bit DDR3 Interface
          2. 7.2.2.4.2 16-Bit DDR3 Interface
        5. 7.2.2.5  Compatible JEDEC DDR3 Devices
        6. 7.2.2.6  PCB Stackup
        7. 7.2.2.7  Placement
        8. 7.2.2.8  DDR3 Keepout Region
        9. 7.2.2.9  Bulk Bypass Capacitors
        10. 7.2.2.10 High Speed Bypass Capacitors
          1. 7.2.2.10.1 Return Current Bypass Capacitors
        11. 7.2.2.11 Net Classes
        12. 7.2.2.12 DDR3 Signal Termination
        13. 7.2.2.13 VREF_DDR Routing
        14. 7.2.2.14 VTT
        15. 7.2.2.15 CK and ADDR_CTRL Topologies and Routing Definition
          1. 7.2.2.15.1 Four DDR3 Devices
            1. 7.2.2.15.1.1 CK and ADDR_CTRL Topologies, Four DDR3 Devices
            2. 7.2.2.15.1.2 CK and ADDR_CTRL Routing, Four DDR3 Devices
          2. 7.2.2.15.2 Two DDR3 Devices
            1. 7.2.2.15.2.1 CK and ADDR_CTRL Topologies, Two DDR3 Devices
            2. 7.2.2.15.2.2 CK and ADDR_CTRL Routing, Two DDR3 Devices
          3. 7.2.2.15.3 One DDR3 Device
            1. 7.2.2.15.3.1 CK and ADDR_CTRL Topologies, One DDR3 Device
            2. 7.2.2.15.3.2 CK and ADDR/CTRL Routing, One DDR3 Device
        16. 7.2.2.16 Data Topologies and Routing Definition
          1. 7.2.2.16.1 DQS and DQ/DM Topologies, Any Number of Allowed DDR3 Devices
          2. 7.2.2.16.2 DQS and DQ/DM Routing, Any Number of Allowed DDR3 Devices
        17. 7.2.2.17 Routing Specification
          1. 7.2.2.17.1 CK and ADDR_CTRL Routing Specification
          2. 7.2.2.17.2 DQS and DQ Routing Specification
    3. 7.3 High Speed Differential Signal Routing Guidance
    4. 7.4 Power Distribution Network Implementation Guidance
    5. 7.5 Thermal Solution Guidance
    6. 7.6 Single-Ended Interfaces
      1. 7.6.1 General Routing Guidelines
      2. 7.6.2 QSPI Board Design and Layout Guidelines
    7. 7.7 LJCB_REFN/P Connections
    8. 7.8 Clock Routing Guidelines
      1. 7.8.1 32-kHz Oscillator Routing
      2. 7.8.2 Oscillator Ground Connection
  8. 8Device and Documentation Support
    1. 8.1 Device Nomenclature
      1. 8.1.1 Standard Package Symbolization
      2. 8.1.2 Device Naming Convention
    2. 8.2 Tools and Software
    3. 8.3 Documentation Support
    4. 8.4 Related Links
    5. 8.5 Support Resources
    6. 8.6 Trademarks
    7. 8.7 Electrostatic Discharge Caution
    8. 8.8 Glossary
  9. 9Mechanical, Packaging, and Orderable Information
    1. 9.1 Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • ABZ|760
Thermal pad, mechanical data (Package|Pins)
Orderable Information

MPU

The dual Cortex®-A15 microprocessor unit (MPU) subsystem serves the applications processing role by running the high-level operating system (HLOS) and application code.

The MPU subsystem incorporates two Cortex-A15 MPU cores (MPU_C0 and MPU_C1), individual level 1 (L1) caches, level 2 (L2) cache (MPU_L2CACHE) shared between them, and various other shared peripherals. To aid software development, the processor cores can be kept cache-coherent with each other and with the L2 cache.

The MPU subsystem provides a high-performance computing platform with high peak-computing performance and low memory latency.

The MPU subsystem integrates the following:

  • Arm Cortex-A15 MP Core (MPU_CLUSTER)
    • Two Cortex-A15 MPU cores (revision r2p2, SMP architecture), each of them having the following features:
      • Superscalar, dynamic multi-issue technology
        • Out-of-order (OoO) instruction dispatch and completion
        • Dynamic branch prediction with branch target buffer (BTB), global history buffer (GHB), and 48-entry return stack
        • Continuous fetch and decoding of three instructions per clock cycle
        • Dispatch of up to four instructions and completion of eight instructions per clock cycle
        • Provides optimal performance from binaries compiled for previous Arm processors
        • Five execution units handle simple instructions, branch instructions, Arm® Neon™ and floating point instructions, multiply instructions, and load and store instructions.
        • Simple instructions take two cycles from dispatch, while complex instructions take up to 11 cycles.
        • Can issue two simple instructions in a cycle
        • Can issue a load and a store instruction in the same cycle
      • Integrated Arm® Neon™ processing engine to include the Arm® Neon™ Advanced SIMD (single instruction, multiple data) support for accelerated media and signal processing computation
      • Includes VFPv4-compatible hardware to support single- and double-precision add, subtract, divide, multiply and accumulate, and square root operations
      • Extensive support to accelerate virtualization using a hypervisor
      • 32-KiB L1 instruction (L1I) and 32-KiB L1 data (L1D) cache:
        • 64-byte line size
        • 2-way set associative
      • Memory management unit (MMU):
        • Two-level translation lookaside buffer (TLB) organization
          • First level is an 32-entry, fully associative micro-TLB implemented for each of instruction fetch, load, and store.
          • Second level is a unified, 4-way associative, 512-entry main TLB
        • Supports hardware TLB table-walk for backward-compatible and new 64-bit entry page table formats
        • New page table format can produce 40-bit physical addresses
        • Two-stage translation where first stage is HLOS-controlled and the second level may be controlled by a hypervisor. Second stage always uses the new page table format
    • Integrated L2 cache (MPU_L2CACHE) and snoop control unit (SCU):
      • 2-MiB of unified (instructions and data) cache organized as 16 ways of 2048 sets of 64-byte lines
      • Redundant L1 data (cache) tags to perform snoop filtering (L1 instruction cache tags are not duplicated)
      • Operates at Cortex-A15 MPU core clock rate
      • Integrated L2 cache controller (MPU_L2CACHE_CTRL):
        • Sixteen 64-byte line buffers that handle evictions, line fills and snoop transfers
        • One 128-bit AMBA4 Coherent Bus (AXI4-ACE) port
        • Auto-prefetch buffer for up to 16 streams per core and detecting forward and backward strides
    • Generalized interrupt controller (GIC, also referred to as MPU_INTC): An interrupt controller supplied by Arm. The single GIC in the MPU_CLUSTER routes interrupts to each of the MPU cores. The GIC supports:
      • Number of shared peripheral interrupts (SPI): 160
      • Number of software generated interrupts (SGI): 16
      • Number of CPU interfaces: 2
      • Virtual CPU interface for virtualization support. This allows the majority of guest operating system (OS) interactions with the GIC to be handled in hardware, but with physical interrupts still requiring hypervisor intervention to assign them to the appropriate virtual machine.
    • Integrated timer counter and one timer block per MPU core
    • Arm® CoreSight™ debug and trace modules. For more information, see On-Chip Debug Support chapter in the device TRM.
  • MPU_AXI2OCP bridge (local interconnect):
    • Connected to Memory Adapter (MPU_MA), which routes the non-EMIF address space transactions to MPU_AXI2OCP
    • Single request multiple data (SRMD) protocol on L3_MAIN port
    • Multiple targets:
      • 64-bit port to the L3_MAIN interconnect. Interface frequency is 1/4 or 1/8 of core frequency
      • MPU_ROM
      • Internal MPU subsystem peripheral targets, including Memory Adapter LISA Section Manager (MA_LSM), wake-up generator (MPU_WUGEN), watchdog timer (MPU_WD_TIMER), and local PRCM module (MPU_PRCM) configuration
      • Internal AXI target, Arm® CoreSight™ System Trace Module (CS_STM)
  • Memory adapter (MPU_MA): Helps decrease the latency of accesses between the MPU_L2CACHE and the two EMIFs (EMIF0 and EMIF1) by providing a direct path between the MPU subsystem and the EMIFs:
    • Connected to 128-bit AMBA4 interface of MPU_CLUSTER
    • Direct 128-bit interface to each of EMIF0 and EMIF1
    • Interface speed between MPU_CLUSTER and MPU_MA is at half-speed of MPU_CLUSTER internal core frequency
    • Quarter-speed interface to EMIF
    • Uses firewall logic to check access rights of incoming addressess
  • Local PRCM (MPU_PRCM):
    • Handles MPU_C0 and MPU_C1 power domains
    • Supports SR3-APG (SmartReflex3 Automatic Power Gating) power management technology inside the MPU_CLUSTER
    • MPU subsystem has six power domains
  • Wake-up generator (MPU_WUGEN)
    • Responsible for waking up the MPU cores
  • Standby controller: Handles the power transitions inside the MPU subsystem
  • Realtime (master) counter (COUNTER_REALTIME): Produces the count used by the private timer peripherals in the MPU_CLUSTER
  • Watchdog timer (MPU_WD_TIMER): Used to generate a chip-level watchdog reset request to global PRCM
  • On-chip boot ROM (MPU_ROM): The MPU_ROM size is 48-KiB, and the address range is from 0x4003 8000 to 0x4004 3FFF. For more information about booting from this memory, see Initialization chapter in the device TRM.
  • Interfaces:
    • 128-bit interface to each of EMIF0 and EMIF1
    • 64-bit master port to the L3_MAIN interconnect
    • 32-bit slave port from the L4_CFG_EMU interconnect (debug subsystem) for configuration of the MPU subsystem debug modules
    • 32-bit slave port from the L4_CFG interconnect for memory adapter firewall (MPU_MA_NTTP_FW) configuration
    • 32-bit ATB output for transmitting debug and trace data
    • 160 peripheral interrupt inputs

For more information, see Dual Cortex-A15 MPU Subsystem chapter in the device TRM.