SWRS236C March   2021  – January 2024 AWR1843AOP

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
    1. 3.1 Functional Block Diagram
  5. 4 Device Comparison
    1. 4.1 Related Products
  6. 5 Terminal Configuration and Functions
    1. 5.1 Pin Diagram
    2. 5.2 Pin Attributes
    3. 5.3 Signal Descriptions
      1. 5.3.1 Pin Functions - Digital and Analog [ALP Package]
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Power-On Hours (POH)
    4. 6.4  Recommended Operating Conditions
    5. 6.5  Power Supply Specifications
    6. 6.6  Power Consumption Summary
    7. 6.7  RF Specification
    8. 6.8  CPU Specifications
    9. 6.9  Thermal Resistance Characteristics for FCBGA Package [ALP0180A]
    10. 6.10 Timing and Switching Characteristics
      1. 6.10.1  Antenna Radiation Patterns
        1. 6.10.1.1 Antenna Radiation Patterns for Receiver
        2. 6.10.1.2 Antenna Radiation Patterns for Transmitter
      2. 6.10.2  Antenna Positions
      3. 6.10.3  Power Supply Sequencing and Reset Timing
      4. 6.10.4  Input Clocks and Oscillators
        1. 6.10.4.1 Clock Specifications
      5. 6.10.5  Multibuffered / Standard Serial Peripheral Interface (MibSPI)
        1. 6.10.5.1 Peripheral Description
        2. 6.10.5.2 MibSPI Transmit and Receive RAM Organization
          1. 6.10.5.2.1 SPI Timing Conditions
          2. 6.10.5.2.2 SPI Controller Mode Switching Parameters (CLOCK PHASE = 0, SPICLK = output, SPISIMO = output, and SPISOMI = input)
          3. 6.10.5.2.3 SPI Controller Mode Switching Parameters (CLOCK PHASE = 1, SPICLK = output, SPISIMO = output, and SPISOMI = input)
        3. 6.10.5.3 SPI Peripheral Mode I/O Timings
          1. 6.10.5.3.1 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input, and SPISOMI = output)
        4. 6.10.5.4 Typical Interface Protocol Diagram (Slave Mode)
      6. 6.10.6  LVDS Interface Configuration
        1. 6.10.6.1 LVDS Interface Timings
      7. 6.10.7  General-Purpose Input/Output
        1. 6.10.7.1 Switching Characteristics for Output Timing versus Load Capacitance (CL) #GUID-4685AB93-A014-47EA-9F05-952FFC28DBFA/T4362547-45 #GUID-4685AB93-A014-47EA-9F05-952FFC28DBFA/T4362547-50
      8. 6.10.8  Controller Area Network Interface (DCAN)
        1. 6.10.8.1 Dynamic Characteristics for the DCANx TX and RX Pins
      9. 6.10.9  Controller Area Network - Flexible Data-rate (CAN-FD)
        1. 6.10.9.1 Dynamic Characteristics for the CANx TX and RX Pins
      10. 6.10.10 Serial Communication Interface (SCI)
        1. 6.10.10.1 SCI Timing Requirements
      11. 6.10.11 Inter-Integrated Circuit Interface (I2C)
        1. 6.10.11.1 I2C Timing Requirements #GUID-64613E7E-5DDF-4B01-8FA0-13739060F368/T4362547-185
      12. 6.10.12 Quad Serial Peripheral Interface (QSPI)
        1. 6.10.12.1 QSPI Timing Conditions
        2. 6.10.12.2 Timing Requirements for QSPI Input (Read) Timings #GUID-6A95C194-2C40-46FE-9793-4574200DA2C4/T4362547-210 #GUID-6A95C194-2C40-46FE-9793-4574200DA2C4/T4362547-209
        3. 6.10.12.3 QSPI Switching Characteristics
      13. 6.10.13 ETM Trace Interface
        1. 6.10.13.1 ETMTRACE Timing Conditions
        2. 6.10.13.2 ETM TRACE Switching Characteristics
      14. 6.10.14 Data Modification Module (DMM)
        1. 6.10.14.1 DMM Timing Requirements
      15. 6.10.15 JTAG Interface
        1. 6.10.15.1 JTAG Timing Conditions
        2. 6.10.15.2 Timing Requirements for IEEE 1149.1 JTAG
        3. 6.10.15.3 Switching Characteristics Over Recommended Operating Conditions for IEEE 1149.1 JTAG
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Subsystems
      1. 7.3.1 RF and Analog Subsystem
        1. 7.3.1.1 Clock Subsystem
        2. 7.3.1.2 Transmit Subsystem
        3. 7.3.1.3 Receive Subsystem
      2. 7.3.2 Processor Subsystem
      3. 7.3.3 Automotive Interface
      4. 7.3.4 Main Subsystem Cortex-R4F Memory Map
      5. 7.3.5 DSP Subsystem Memory Map
    4. 7.4 Other Subsystems
      1. 7.4.1 ADC Channels (Service) for User Application
        1. 7.4.1.1 GP-ADC Parameter
  9. 8 Monitoring and Diagnostics
    1. 8.1 Monitoring and Diagnostic Mechanisms
      1. 8.1.1 Error Signaling Module
  10. 9 Applications, Implementation, and Layout
    1. 9.1 Application Information
    2. 9.2 Reference Schematic
  11. 10Device and Documentation Support
    1. 10.1 Device Nomenclature
    2. 10.2 Tools and Software
    3. 10.3 Documentation Support
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1. 12.1 Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • ALP|180
Thermal pad, mechanical data (Package|Pins)
Orderable Information

5.2 Pin Attributes

Table 5-1 Pin Attributes (ALP180A Package)
BALL NUMBER [1] BALL NAME [2] SIGNAL NAME [3] PINCNTL ADDRESS [4] MODE [5][9] TYPE [6] BALL RESET STATE [7] PULL UP/DOWN TYPE [8]
M2 GPIO_0 GPIO_13 0xFFFFEA04 0 IO Output Disabled Pull Down
GPIO_0 1 IO
PMIC_CLKOUT 2 O
ADC_VALID 7 O
EPWM1B 10 O
ePWM2A 11 O
L3 GPIO_1 GPIO_16 0xFFFFEA08 0 IO Output Disabled Pull Down
GPIO_1 1 IO
SYNC_OUT 2 O
ADC_VALID 7 O
DMM_MUX_IN 12 I
SPIB_CS_N_1 13 IO
SPIB_CS_N_2 14 IO
EPWM1SYNCI 15 I
K3 GPIO_2 GPIO_26 0xFFFFEA64 0 IO Output Disabled Pull Down
GPIO_2 1 IO
OSC_CLKOUT 2 O
MSS_UARTB_TX 7 O
BSS_UART_TX 8 O
SYNC_OUT 9 O
PMIC_CLKOUT 10 O
CHIRP_START 11 O
CHIRP_END 12 O
FRAME_START 13 O
U7 GPIO_31 (DP0) TRACE_DATA_0 0xFFFFEA7C 0 O Output Disabled Pull Down
GPIO_31 1 IO
DMM0 2 I
MSS_UARTA_TX 4 IO
U6 GPIO_32 (DP1) TRACE_DATA_1 0xFFFFEA80 0 O Output Disabled Pull Down
GPIO_32 1 IO
DMM1 2 I
V5 GPIO_33 (DP2) TRACE_DATA_2 0xFFFFEA84 0 O Output Disabled Pull Down
GPIO_33 1 IO
DMM2 2 I
U5 GPIO_34 (DP3) TRACE_DATA_3 0xFFFFEA88 0 O Output Disabled Pull Down
GPIO_34 1 IO
DMM3 2 I
EPWM3SYNCO 4 O
V3 GPIO_35 (DP4) TRACE_DATA_4 0xFFFFEA8C 0 O Output Disabled Pull Down
GPIO_35 1 IO
DMM4 2 I
EPWM2SYNCO 4 O
M1 GPIO_36 (DP5) TRACE_DATA_5 0xFFFFEA90 0 O Output Disabled Pull Down
GPIO_36 1 IO
DMM5 2 I
MSS_UARTB_TX 5 O
L2 GPIO_37 (DP6) TRACE_DATA_6 0xFFFFEA94 0 O Output Disabled Pull Down
GPIO_37 1 IO
DMM6 2 I
BSS_UART_TX 5 O
L1 GPIO_38 (DP7) TRACE_DATA_7 0xFFFFEA98 0 O Output Disabled Pull Down
GPIO_38 1 IO
DMM7 2 I
DSS_UART_TX 5 O
C3 GPIO_39 (DP8) TRACE_DATA_8 0xFFFFEA9C 0 O Output Disabled Pull Down
GPIO_39 1 IO
DMM8 2 I
CAN_FD_TX 4 O
EPWM1SYNCI 5 I
B3 GPIO_40 (DP9) TRACE_DATA_9 0xFFFFEAA0 0 O Output Disabled Pull Down
GPIO_40 1 IO
DMM9 2 I
CAN_FD_RX 4 I
EPWM1SYNCO 5 O
C4 GPIO_41 (DP10) TRACE_DATA_10 0xFFFFEAA4 0 O Output Disabled Pull Down
GPIO_41 1 IO
DMM10 2 I
EPWM3A 4 O
A3 GPIO_42 (DP11) TRACE_DATA_11 0xFFFFEAA8 0 O Output Disabled Pull Down
GPIO_42 1 IO
DMM11 2 I
EPWM3B 4 O
B4 GPIO_43 (DP12) TRACE_DATA_12 0xFFFFEAAC 0 O Output Disabled Pull Down
GPIO_43 1 IO
DMM12 2 I
EPWM1A 4 O
CAN_FD_TX 5 O
A4 GPIO_44 (DP13) TRACE_DATA_13 0xFFFFEAB0 0 O Output Disabled Pull Down
GPIO_44 1 IO
DMM13 2 I
EPWM1B 4 O
CAN_FD_RX 5 I
C5 GPIO_45 (DP14) TRACE_DATA_14 0xFFFFEAB4 0 O Output Disabled Pull Down
GPIO_45 1 IO
DMM14 2 I
EPWM2A 4 O
B5 GPIO_46 (DP15) TRACE_DATA_15 0xFFFFEAB8 0 O Output Disabled Pull Down
GPIO_46 1 IO
DMM15 2 I
EPWM2B 4 O
U3 GPIO_47 (DMM_CLK) TRACE_CLK 0xFFFFEABC 0 O Output Disabled Pull Down
GPIO_47 1 IO
DMM_CLK 2 I
U4 DMM_SYNC TRACE_CTL 0xFFFFEAC0 0 O Output Disabled Pull Down
DMM_SYNC 2 I
V13 MCU_CLKOUT GPIO_25 0xFFFFEA60 0 IO Output Disabled Pull Down
MCU_CLKOUT 1 O
CHIRP_START 2 O
CHIRP_END 6 O
FRAME_START 7 O
EPWM1A 12 O
U14 NERROR_IN NERROR_IN 0xFFFFEA44 0 I Input
U15 NERROR_OUT NERROR_OUT 0xFFFFEA4C 0 O Hi-Z (Open Drain)
V10 PMIC_CLKOUT SOP[2] 0xFFFFEA68 During Power Up I Output Disabled Pull Down
GPIO_27 0 IO
PMIC_CLKOUT 1 O
CHIRP_START 6 O
CHIRP_END 7 O
FRAME_START 8 O
EPWM1B 11 O
EPWM2A 12 O
H3 QSPI[0] GPIO_8 0xFFFFEA2C 0 IO Output Disabled Pull Down
QSPI[0] 1 IO
SPIB_MISO 2 IO
G2 QSPI[1] GPIO_9 0xFFFFEA30 0 IO Output Disabled Pull Down
QSPI[1] 1 I
SPIB_MOSI 2 IO
SPIB_CS_N_2 8 IO
J3 QSPI[2] GPIO_10 0xFFFFEA34 0 IO Output Disabled Pull Down
QSPI[2] 1 I
CAN_FD_TX 8 O
K2 QSPI[3] GPIO_11 0xFFFFEA38 0 IO Output Disabled Pull Down
QSPI[3] 1 I
CAN_FD_RX 8 I
H2 QSPI_CLK GPIO_7 0xFFFFEA3C 0 IO Output Disabled Pull Down
QSPI_CLK 1 O
SPIB_CLK 2 IO
DSS_UART_TX 6 O
J2 QSPI_CS_N GPIO_6 0xFFFFEA40 0 IO Output Disabled Pull Up
QSPI_CS_N 1 O
SPIB_CS_N 2 IO
V16 RS232_RX GPIO_15 0xFFFFEA74 0 IO Input Enabled Pull Up
RS232_RX 1 I
MSS_UARTA_RX 2 I
BSS_UART_TX 6 IO
MSS_UARTB_RX 7 IO
CAN_FD_RX 8 I
I2C_SCL 9 IO
EPWM2A 10 O
EPWM2B 11 O
EPWM3A 12 O
U16 RS232_TX GPIO_14 0xFFFFEA78 0 IO Output Enabled
RS232_TX 1 O
MSS_UARTA_TX 5 IO
MSS_UARTB_TX 6 IO
BSS_UART_TX 7 IO
CAN_FD_TX 10 O
I2C_SDA 11 IO
EPWM1A 12 O
EPWM1B 13 O
NDMM_EN 14 I
EPWM2A 15 O
D2 SPIA_CLK GPIO_3 0xFFFFEA14 0 IO Output Disabled Pull Up
SPIA_CLK 1 IO
CAN_RX 6 I
DSS_UART_TX 7 O
C2 SPIA_CS_N GPIO_30 0xFFFFEA18 0 IO Output Disabled Pull Up
SPIA_CS_N 1 IO
CAN_TX 6 O
D1 SPIA_MISO GPIO_20 0xFFFFEA10 0 IO Output Disabled Pull Up
SPIA_MISO 1 IO
CAN_FD_TX 2 O
F2 SPIA_MOSI GPIO_19 0xFFFFEA0C 0 IO Output Disabled Pull Up
SPIA_MOSI 1 IO
CAN_FD_RX 2 I
DSS_UART_TX 8 O
E2 SPIB_CLK GPIO_5 0xFFFFEA24 0 IO Output Disabled Pull Up
SPIB_CLK 1 IO
MSS_UARTA_RX 2 I
MSS_UARTB_TX 6 O
BSS_UART_TX 7 O
CAN_FD_RX 8 I
D3 SPIB_CS_N GPIO_4 0xFFFFEA28 0 IO Output Disabled Pull Up
SPIB_CS_N 1 IO
MSS_UARTA_TX 2 O
MSS_UARTB_TX 6 O
BSS_UART_TX 7 IO
QSPI_CLK_EXT 8 I
CAN_FD_TX 9 O
G3 SPIB_MISO GPIO_22 0xFFFFEA20 0 IO Output Disabled Pull Up
SPIB_MISO 1 IO
I2C_SCL 2 IO
DSS_UART_TX 6 O
G1 SPIB_MOSI GPIO_21 0xFFFFEA1C 0 IO Output Disabled Pull Up
SPIB_MOSI 1 IO
I2C_SDA 2 IO
B2 SPI_HOST_INTR GPIO_12 0xFFFFEA00 0 IO Output Disabled Pull Down
SPI_HOST_INTR 1 O
ADC_VALID 2 O
SPIB_CS_N_1 6 IO
U12 SYNC_IN GPIO_28 0xFFFFEA6C 0 IO Output Disabled Pull Down
SYNC_IN 1 I
MSS_UARTB_RX 6 IO
DMM_MUX_IN 7 I
SYNC_OUT 9 O
M3 SYNC_OUT SOP[1] 0xFFFFEA70 During Power Up I Output Disabled Pull Down
GPIO_29 0 IO
SYNC_OUT 1 O
DMM_MUX_IN 9 I
SPIB_CS_N_1 10 IO
SPIB_CS_N_2 11 IO
T3 TCK GPIO_17 0xFFFFEA50 0 IO Input Enabled Pull Down
TCK 1 I
MSS_UARTB_TX 2 O
CAN_FD_TX 8 O
U9 TDI GPIO_23 0xFFFFEA58 0 IO Input Enabled Pull Up
TDI 1 I
MSS_UARTA_RX 2 I
U10 TDO SOP[0] 0xFFFFEA5C During Power Up I Output Enabled
GPIO_24 0 IO
TDO 1 O
MSS_UARTA_TX 2 O
MSS_UARTB_TX 6 O
BSS_UART_TX 7 O
NDMM_EN 9 I
U8 TMS GPIO_18 0xFFFFEA54 0 IO Input Enabled Pull Down
TMS 1 I
BSS_UART_TX 2 O
CAN_FD_RX 6 I
U13 WARM_RESET WARM_RESET 0xFFFFEA48 0 IO Hi-Z Input (Open Drain)
R2 LVDS_CLKM LVDS_CLKM O
R1 LVDS_CLKP LVDS_CLKP O
N2 LVDS_TXP[0] LVDS_TXP[0] O
N1 LVDS_TXM[0] LVDS_TXM[0] O
P2 LVDS_TXP[1] LVDS_TXP[1] O
P1 LVDS_TXM[1] LVDS_TXM[1] O
T1 LVDS_FRCLKP LVDS_FRCLKP O
T2 LVDS_FRCLKM LVDS_FRCLKM O
U11 NRESET NRESET I
A7 CLKP CLKP I
B7 CLKM CLKM I
A14 OSC_CLKOUT OSC_CLKOUT O
A16 VBGAP VBGAP O
E1 VDDIN VDDIN PWR
J1 VDDIN VDDIN PWR
V4 VDDIN VDDIN PWR
V8 VDDIN VDDIN PWR
V15 VDDIN VDDIN PWR
A5 VIN_SRAM VIN_SRAM PWR
V6 VIN_SRAM VIN_SRAM PWR
V12 VIN_SRAM VIN_SRAM PWR
C1 VNWA VNWA PWR
V7 VNWA VNWA PWR
V14 VNWA VNWA PWR
H1 VIOIN VIOIN PWR
V9 VIOIN VIOIN PWR
B1 VIOIN_18 VIOIN_18 PWR
F1 VIOIN_18 VIOIN_18 PWR
K1 VIOIN_18 VIOIN_18 PWR
V11 VIOIN_18 VIOIN_18 PWR
C15 VIN_18CLK VIN_18CLK PWR
C18 VIN_18CLK VIN_18CLK PWR
U2 VIOIN_18DIFF VIOIN_18DIFF PWR
V2 VPP VPP PWR
J16 VIN_13RF1 VIN_13RF1 PWR
J17 VIN_13RF1 VIN_13RF1 PWR
J18 VIN_13RF1 VIN_13RF1 PWR
H16 VIN_13RF2 VIN_13RF2 PWR
H17 VIN_13RF2 VIN_13RF2 PWR
H18 VIN_13RF2 VIN_13RF2 PWR
M16 VIN_18BB VIN_18BB PWR
M17 VIN_18BB VIN_18BB PWR
M18 VIN_18BB VIN_18BB PWR
A12 VIN_18VCO VIN_18VCO PWR
C11 VIN_18VCO VIN_18VCO PWR
A1 VSS VSS GND
A2 VSS VSS GND
E3 VSS VSS GND
F3 VSS VSS GND
N3 VSS VSS GND
P3 VSS VSS GND
R3 VSS VSS GND
T4 VSS VSS GND
T5 VSS VSS GND
T6 VSS VSS GND
T7 VSS VSS GND
T8 VSS VSS GND
T9 VSS VSS GND
T10 VSS VSS GND
T11 VSS VSS GND
T12 VSS VSS GND
T13 VSS VSS GND
T14 VSS VSS GND
T15 VSS VSS GND
T16 VSS VSS GND
U1 VSS VSS GND
V1 VSS VSS GND
A6 VSSA VSSA GND
A8 VSSA VSSA GND
A11 VSSA VSSA GND
A13 VSSA VSSA GND
A15 VSSA VSSA GND
A17 VSSA VSSA GND
A18 VSSA VSSA GND
B6 VSSA VSSA GND
B8 VSSA VSSA GND
B9 VSSA VSSA GND
B10 VSSA VSSA GND
B11 VSSA VSSA GND
B12 VSSA VSSA GND
B13 VSSA VSSA GND
B14 VSSA VSSA GND
B15 VSSA VSSA GND
B16 VSSA VSSA GND
B17 VSSA VSSA GND
B18 VSSA VSSA GND
C6 VSSA VSSA GND
C7 VSSA VSSA GND
C8 VSSA VSSA GND
C12 VSSA VSSA GND
C13 VSSA VSSA GND
C14 VSSA VSSA GND
C16 VSSA VSSA GND
C17 VSSA VSSA GND
D16 VSSA VSSA GND
D17 VSSA VSSA GND
D18 VSSA VSSA GND
E16 VSSA VSSA GND
E17 VSSA VSSA GND
E18 VSSA VSSA GND
F16 VSSA VSSA GND
F17 VSSA VSSA GND
F18 VSSA VSSA GND
K16 VSSA VSSA GND
K17 VSSA VSSA GND
K18 VSSA VSSA GND
L16 VSSA VSSA GND
L17 VSSA VSSA GND
L18 VSSA VSSA GND
N16 VSSA VSSA GND
N17 VSSA VSSA GND
N18 VSSA VSSA GND
P16 VSSA VSSA GND
R16 VSSA VSSA GND
R17 VSSA VSSA GND
T17 VSSA VSSA GND
U17 VSSA VSSA GND
U18 VSSA VSSA GND
V17 VSSA VSSA GND
V18 VSSA VSSA GND
A10 VOUT_14APLL VOUT_14APLL O
A9 VOUT_14SYNTH VOUT_14SYNTH O
G16 VOUT_PA VOUT_PA IO
G17 VOUT_PA VOUT_PA IO
G18 VOUT_PA VOUT_PA IO
P18 Analog Test1 / GPADC1 Analog Test1 / GPADC1 IO
P17 Analog Test2 / GPADC2 Analog Test2 / GPADC2 IO
R18 Analog Test3 / GPADC3 Analog Test3 / GPADC3 IO
T18 Analog Test4 / GPADC4 Analog Test4 / GPADC4 IO
C9 ANAMUX / GPADC5 ANAMUX / GPADC5 IO
C10 VSENSE / GPADC6 VSENSE / GPADC6 IO

The following list describes the table column headers:

  1. BALL NUMBER: Ball numbers on the bottom side associated with each signal on the bottom.
  2. BALL NAME: Mechanical name from package device (name is taken from muxmode 1).
  3. SIGNAL NAME: Names of signals multiplexed on each ball (also notice that the name of the ball is the signal name in muxmode 1).
  4. PINCNTL ADDRESS: MSS Address for PinMux Control
  5. MODE: Multiplexing mode number: value written to PinMux Cntl register to select specific Signal name for this Ball number. Mode column has bit range value.
  6. TYPE: Signal type and direction:
    • I = Input
    • O = Output
    • IO = Input or Output
  7. BALL RESET STATE: The state of the terminal after supplies are stable after power-on-reset (NRESET) is asserted
  8. PULL UP/DOWN TYPE: indicates the presence of an internal pullup or pulldown resistor. Pullup and pulldown resistors can be enabled or disabled via software.
    • Pull Up: Internal pullup
    • Pull Down: Internal pulldown
    • An empty box means No pull.
  9. Pin Mux Control Value maps to lower 4 bits of register.

 

IO MUX registers are available in the MSS memory map and the respective mapping to device pins is as follows:

Table 5-2 PAD IO Control Registers
Default Pin/Ball Name Package Ball /Pin (Address) Pin Mux Config Register
SPI_HOST_INTR B2 0xFFFFEA00
GPIO_0 M2 0xFFFFEA04
GPIO_1 L3 0xFFFFEA08
SPIA_MOSI F2 0xFFFFEA0C
SPIA_MISO D1 0xFFFFEA10
SPIA_CLK D2 0xFFFFEA14
SPIA_CS_N C2 0xFFFFEA18
SPIB_MOSI G1 0xFFFFEA1C
SPIB_MISO G3 0xFFFFEA20
SPIB_CLK E2 0xFFFFEA24
SPIB_CS_N D3 0xFFFFEA28
QSPI[0] H3 0xFFFFEA2C
QSPI[1] G2 0xFFFFEA30
QSPI[2] J3 0xFFFFEA34
QSPI[3] K2 0xFFFFEA38
QSPI_CLK H2 0xFFFFEA3C
QSPI_CS_N J2 0xFFFFEA40
NERROR_IN U14 0xFFFFEA44
WARM_RESET U13 0xFFFFEA48
NERROR_OUT U15 0xFFFFEA4C
TCK T3 0xFFFFEA50
TMS U8 0xFFFFEA54
TDI U9 0xFFFFEA58
TDO U10 0xFFFFEA5C
MCU_CLKOUT V13 0xFFFFEA60
GPIO_2 K3 0xFFFFEA64
PMIC_CLKOUT V10 0xFFFFEA68
SYNC_IN U12 0xFFFFEA6C
SYNC_OUT M3 0xFFFFEA70
RS232_RX V16 0xFFFFEA74
RS232_TX U16 0xFFFFEA78
GPIO_31 U7 0xFFFFEA7C
GPIO_32 U6 0xFFFFEA80
GPIO_33 V5 0xFFFFEA84
GPIO_34 U5 0xFFFFEA88
GPIO_35 V3 0xFFFFEA8C
GPIO_36 M1 0xFFFFEA90
GPIO_37 L2 0xFFFFEA94
GPIO_38 L1 0xFFFFEA98
GPIO_39 C3 0xFFFFEA9C
GPIO_40 B3 0xFFFFEAA0
GPIO_41 C4 0xFFFFEAA4
GPIO_42 A3 0xFFFFEAA8
GPIO_43 B4 0xFFFFEAAC
GPIO_44 A4 0xFFFFEAB0
GPIO_45 C5 0xFFFFEAB4
GPIO_46 B5 0xFFFFEAB8
GPIO_47 U3 0xFFFFEABC
DMM_SYNC U4 0xFFFFEAC0

The register layout is as follows:

Table 5-3 PAD IO Register Bit Descriptions
BIT FIELD TYPE RESET (POWER ON DEFAULT) DESCRIPTION
31-11 NU RW 0 Reserved
10 SC RW 0 IO slew rate control:
0 = Higher slew rate
1 = Lower slew rate
9 PUPDSEL RW 0 Pullup/PullDown Selection
0 = Pull Down
1 = Pull Up (This field is valid only if Pull Inhibit is set as '0')
8 PI RW 0 Pull Inhibit/Pull Disable
0 = Enable
1 = Disable
7 OE_OVERRIDE RW 1 Output Override
6 OE_OVERRIDE_CTRL RW 1 Output Override Control:
(A '1' here overrides any o/p manipulation of this IO by any of the peripheral block hardware it is associated with for example a SPI Chip select)
5 IE_OVERRIDE RW 0 Input Override
4 IE_OVERRIDE_CTRL RW 0 Input Override Control:
(A '1' here overrides any i/p value on this IO with a desired value)
3-0 FUNC_SEL RW 1 Function select for Pin Multiplexing (Refer to the Pin Mux Sheet)