SLUSE66A June   2020  – January 2021 BQ25731

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Description (continued)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics(BQ25731)
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up Sequence
      2. 9.3.2  Two-Level Battery Discharge Current Limit
      3. 9.3.3  Fast Role Swap Feature
      4. 9.3.4  CHRG_OK Indicator
      5. 9.3.5  Input and Charge Current Sensing
      6. 9.3.6  Input Voltage and Current Limit Setup
      7. 9.3.7  Battery Cell Configuration
      8. 9.3.8  Device HIZ State
      9. 9.3.9  USB On-The-Go (OTG)
      10. 9.3.10 Converter Operation
      11. 9.3.11 Inductance Detection Through IADPT Pin
      12. 9.3.12 Converter Compensation
      13. 9.3.13 Continuous Conduction Mode (CCM)
      14. 9.3.14 Pulse Frequency Modulation (PFM)
      15. 9.3.15 Switching Frequency and Dithering Feature
      16. 9.3.16 Current and Power Monitor
        1. 9.3.16.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.16.2 High-Accuracy Power Sense Amplifier (PSYS)
      17. 9.3.17 Input Source Dynamic Power Management
      18. 9.3.18 Input Current Optimizer (ICO)
      19. 9.3.19 Two-Level Adapter Current Limit (Peak Power Mode)
      20. 9.3.20 Processor Hot Indication
        1. 9.3.20.1 PROCHOT During Low Power Mode
        2. 9.3.20.2 PROCHOT Status
      21. 9.3.21 Device Protection
        1. 9.3.21.1 Watchdog Timer
        2. 9.3.21.2 Input Overvoltage Protection (ACOV)
        3. 9.3.21.3 Input Overcurrent Protection (ACOC)
        4. 9.3.21.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.21.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.21.6 Battery Discharge Overcurrent Protection (BATOC)
        7. 9.3.21.7 Battery Short Protection (BATSP)
        8. 9.3.21.8 System Undervoltage Lockout (VSYS_UVP)
        9. 9.3.21.9 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)-Patented Technology
    5. 9.5 Programming
      1. 9.5.1 I2C Serial Interface
        1. 9.5.1.1 Timing Diagrams
        2. 9.5.1.2 Data Validity
        3. 9.5.1.3 START and STOP Conditions
        4. 9.5.1.4 Byte Format
        5. 9.5.1.5 Acknowledge (ACK) and Not Acknowledge (NACK)
        6. 9.5.1.6 Target Address and Data Direction Bit
        7. 9.5.1.7 Single Read and Write
        8. 9.5.1.8 Multi-Read and Multi-Write
        9. 9.5.1.9 Write 2-Byte I2C Commands
    6. 9.6 Register Map
      1. 9.6.1  ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
      2. 9.6.2  ChargeCurrent Register (I2C address = 03/02h) [reset = 0080h]
        1. 9.6.2.1 Battery Low Voltage Current Clamp
      3. 9.6.3  ChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      4. 9.6.4  ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
      5. 9.6.5  ProchotStatus Register (I2C address = 23/22h) [reset = B800h]
      6. 9.6.6  IIN_DPM Register (I2C address = 25/24h) [reset = 4100h]
      7. 9.6.7  ADCVBUS/PSYS Register (I2C address = 27/26h)
      8. 9.6.8  ADCIBAT Register (I2C address = 29/28h)
      9. 9.6.9  ADCIIN/CMPIN Register (I2C address = 2B/2Ah)
      10. 9.6.10 ADCVSYS/VBAT Register (I2C address = 2D/2Ch)
      11. 9.6.11 ChargeOption1 Register (I2C address = 31/30h) [reset = 3F00h]
      12. 9.6.12 ChargeOption2 Register (I2C address = 33/32h) [reset = 00B7]
      13. 9.6.13 ChargeOption3 Register (I2C address = 35/34h) [reset = 0434h]
      14. 9.6.14 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A81h(2S~5s) 4A09(1S)]
      15. 9.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
      16. 9.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      17. 9.6.17 ChargeOption4 Register (I2C address = 3D/3Ch) [reset = 0048h]
      18. 9.6.18 Vmin Active Protection Register (I2C address = 3F/3Eh) [reset = 006Ch(2s~5s)/0004h(1S)]
      19. 9.6.19 OTGVoltage Register (I2C address = 07/06h) [reset = 09C4h]
      20. 9.6.20 OTGCurrent Register (I2C address = 09/08h) [reset = 3C00h]
      21. 9.6.21 InputVoltage(VINDPM) Register (I2C address = 0B/0Ah) [reset =VBUS-1.28V]
      22. 9.6.22 IIN_HOST Register (I2C address = 0F/0Eh) [reset = 2000h]
      23. 9.6.23 ID Registers
        1. 9.6.23.1 ManufactureID Register (I2C address = 2Eh) [reset = 40h]
        2. 9.6.23.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = D6h]
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Input Snubber and Filter for Voltage Spike Damping
        2. 10.2.2.2 ACP-ACN Input Filter
        3. 10.2.2.3 Inductor Selection
        4. 10.2.2.4 Input Capacitor
        5. 10.2.2.5 Output Capacitor
        6. 10.2.2.6 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]

Figure 9-30 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
7 6 5 4 3 2 1 0
IDCHG_TH1IDCHG_DEG1
R/W R/W R/W R/W R/W R/WR/W R/W
76543210
PP_VINDPMPP_COMPPP_ICRITPP_INOMPP_IDCHG1PP_VSYSPP_BATPRESPP_ACOK
R/WR/WR/WR/WR/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

When the REG0x38h[7:0] are set to be disabled, the PROCHOT event associated with that bit will not be reported in the PROCHOT status register REG0x22h[7:0] any more, and the PROCHOT pin will not be pulled low any more if the event happens.

Table 9-36 ProchotOption1 Register (I2C address = 39h) Field Descriptions
BITFIELDTYPERESETDESCRIPTION
7-2IDCHG_TH1R/W010000b

IDCHG level 1 Threshold

6 bit, range, range 0 A to 64512 mA, step 1024 mA.

Measure current between SRN and SRP.

Trigger when the discharge current is above the threshold.

If the value is programmed to 000000b PROCHOT is always triggered.

Default: 16256 mA or 010000b

1-0IDCHG_DEG1R/W00b

IDCHG level 1 Deglitch Time

00b: 78 ms

01b: 1.25s <default at POR>

10b: 5s

11b: 20s

Table 9-37 ProchotOption1 Register (I2C address = 38h) Field Descriptions
BITFIELDTYPERESETDESCRIPTION
7PP_VINDPMR/W1b

VINDPM PROCHOT Profile

When all the REG0x38[7:0] , REG0x3D[1], REG0x3C[2]bits are 0, PROCHOT function is disabled.

0b: disable

1b: enable<default at POR>

6PP_COMPR/W0b

Independent comparator PROCHOT Profile

When not in low power mode(Battery only), use this bit to control independent comparator PROCHOT profiles.

When in low power mode(Battery only), this bit will lose controllability to independent comparator PROCHOT profiles. Need to use EN_PROCHOT_LPWR to enable independent comparator and its PROCHOT profile.

0b: disable <default at POR>

1b: enable

5PP_ICRITR/W1b

ICRIT PROCHOT Profile

0b: disable

1b: enable <default at POR>

4PP_INOMR/W0b

INOM PROCHOT Profile

0b: disable <default at POR>

1b: enable

3PP_IDCHG1R/W0b

IDCHG1 PROCHOT Profile

0b: disable <default at POR>

1b: enable

2PP_VSYSR/W0b

VSYS PROCHOT Profile

0b: disable <default at POR>

1b: enable

1PP_BATPRESR/W0b

Battery removal PROCHOT Profile

0b: disable <default at POR>

1b: enable (one-shot falling edge triggered)

If BATPRES is enabled in PROCHOT after the battery is removed, it will immediately send out one-shot PROCHOT pulse.

0PP_ACOKR/W0bAdapter removal PROCHOT Profile

0b: disable <default at POR>

1b: enable

EN_LWPWR= 0b to assert PROCHOT pulse after adapter removal.

If PP_ACOK is enabled in PROCHOT after the adapter is removed, it will be pulled low.