SLUSCS3J October   2017  – December 2022 BQ2980 , BQ2982

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Device Configurability
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Overvoltage (OV) Status
      2. 8.3.2 Undervoltage (UV) Status
      3. 8.3.3 Overcurrent in Charge (OCC) Status
      4. 8.3.4 Overcurrent in Discharge (OCD) and Short Circuit in Discharge (SCD) Status
      5. 8.3.5 Overtemperature (OT) Status
      6. 8.3.6 Charge and Discharge Driver
      7. 8.3.7 CTR for FET Override and Device Shutdown
      8. 8.3.8 CTR for PTC Connection
      9. 8.3.9 ZVCHG (0-V Charging)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 Power-On-Reset (POR)
        2. 8.4.1.2 NORMAL Mode
        3. 8.4.1.3 FAULT Mode
        4. 8.4.1.4 SHUTDOWN Mode
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Test Circuits for Device Evaluation
      2. 9.1.2 Test Circuit Diagrams
      3. 9.1.3 Using CTR as FET Driver On/Off Control
    2. 9.2 Typical Applications
      1. 9.2.1 BQ298x Configuration 1: System-Controlled Reset/Shutdown Function
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Selection of Power FET
        4. 9.2.1.4 Application Curves
      2. 9.2.2 BQ298x Configuration 2: CTR Function Disabled
      3. 9.2.3 BQ298x Configuration 3: PTC Thermistor Protection
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Third-Party Products Disclaimer
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.2.1.2 Detailed Design Procedure

  • Determine if a CTR for FET override or an improved voltage measurement function is required in the battery pack design.
  • See Figure 9-6 for the schematic design.
  • Check the cell specification and system requirement to determine OV and UV levels.
  • Define the sense resistor value and system requirement to determine OCC, OCD, and SCD levels. For example, with a 1-mΩ sense resistor and OCC, OCD, and SCD, the requirement is 6 A, 8 A, and 20 A, respectively. The OCC threshold should be set to 6 mV, the OCD threshold should be at 8 mV, and the SCD threshold should be at 20 mV.
  • Determine the required OT protection threshold. The OT fault turns off the CHG and the DSG, so the threshold must account for the highest allowable charge and discharge temperature range.
  • When a decision is made on the various thresholds, search for whether a device configuration is available or contact the local sales office for more information.