SWRS251A May   2021  – November 2021 CC1352P7

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1. 3.1 Functional Block Diagram
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Terminal Configuration and Functions
    1. 6.1 Pin Diagram – RGZ Package (Top View)
    2. 6.2 Signal Descriptions – RGZ Package
    3. 6.3 Connections for Unused Pins and Modules
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Power Supply and Modules
    5. 7.5  Power Consumption - Power Modes
    6. 7.6  Power Consumption - Radio Modes
    7. 7.7  Nonvolatile (Flash) Memory Characteristics
    8. 7.8  Thermal Resistance Characteristics
    9. 7.9  RF Frequency Bands
    10. 7.10 861 MHz to 1054 MHz - Receive (RX)
    11. 7.11 861 MHz to 1054 MHz - Transmit (TX) 
    12. 7.12 861 MHz to 1054 MHz - PLL Phase Noise Wideband Mode
    13. 7.13 861 MHz to 1054 MHz - PLL Phase Noise Narrowband Mode
    14. 7.14 Bluetooth Low Energy - Receive (RX)
    15. 7.15 Bluetooth Low Energy - Transmit (TX)
    16. 7.16 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
    17. 7.17 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - TX
    18. 7.18 Timing and Switching Characteristics
      1. 7.18.1 Reset Timing
      2. 7.18.2 Wakeup Timing
      3. 7.18.3 Clock Specifications
        1. 7.18.3.1 48 MHz Crystal Oscillator (XOSC_HF)
        2. 7.18.3.2 48 MHz RC Oscillator (RCOSC_HF)
        3. 7.18.3.3 2 MHz RC Oscillator (RCOSC_MF)
        4. 7.18.3.4 32.768 kHz Crystal Oscillator (XOSC_LF)
        5. 7.18.3.5 32 kHz RC Oscillator (RCOSC_LF)
      4. 7.18.4 Synchronous Serial Interface (SSI) Characteristics
        1. 7.18.4.1 Synchronous Serial Interface (SSI) Characteristics
        2.       40
      5. 7.18.5 UART
        1. 7.18.5.1 UART Characteristics
    19. 7.19 Peripheral Characteristics
      1. 7.19.1 ADC
        1. 7.19.1.1 Analog-to-Digital Converter (ADC) Characteristics
      2. 7.19.2 DAC
        1. 7.19.2.1 Digital-to-Analog Converter (DAC) Characteristics
      3. 7.19.3 Temperature and Battery Monitor
        1. 7.19.3.1 Temperature Sensor
        2. 7.19.3.2 Battery Monitor
      4. 7.19.4 Comparators
        1. 7.19.4.1 Low-Power Clocked Comparator
        2. 7.19.4.2 Continuous Time Comparator
      5. 7.19.5 Current Source
        1. 7.19.5.1 Programmable Current Source
      6. 7.19.6 GPIO
        1. 7.19.6.1 GPIO DC Characteristics
    20. 7.20 Typical Characteristics
      1. 7.20.1 MCU Current
      2. 7.20.2 RX Current
      3. 7.20.3 TX Current
      4. 7.20.4 RX Performance
      5. 7.20.5 TX Performance
      6. 7.20.6 ADC Performance
  8. 8 Detailed Description
    1. 8.1  Overview
    2. 8.2  System CPU
    3. 8.3  Radio (RF Core)
      1. 8.3.1 Proprietary Radio Formats
      2. 8.3.2 Bluetooth 5.2 Low Energy
      3. 8.3.3 802.15.4 (Thread, Zigbee, 6LoWPAN)
    4. 8.4  Memory
    5. 8.5  Sensor Controller
    6. 8.6  Cryptography
    7. 8.7  Timers
    8. 8.8  Serial Peripherals and I/O
    9. 8.9  Battery and Temperature Monitor
    10. 8.10 µDMA
    11. 8.11 Debug
    12. 8.12 Power Management
    13. 8.13 Clock Systems
    14. 8.14 Network Processor
  9. 9 Application, Implementation, and Layout
    1. 9.1 Reference Designs
    2. 9.2 Junction Temperature Calculation
  10. 10Device and Documentation Support
    1. 10.1 Device Nomenclature
    2. 10.2 Tools and Software
      1. 10.2.1 SimpleLink™ Microcontroller Platform
    3. 10.3 Documentation Support
    4. 10.4 Support Resources
    5. 10.5 Trademarks
    6. 10.6 Electrostatic Discharge Caution
    7. 10.7 Glossary
  11. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.14 Bluetooth Low Energy - Receive (RX)

Measured on the CC1352-P7EM-XD7793-XD24-PA24 reference design with Tc = 25 °C, VDDS = 3.0 V, fRF= 2440 MHz with
DC/DC enabled and high power PA connected to VDDS unless otherwise noted.
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is measured at a dedicated antenna connection. All measurements are performed conducted.
 
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
125 kbps (LE Coded)
Receiver sensitivity Differential mode. BER = 10–3 –104 dBm
Receiver saturation Differential mode. BER = 10–3 >5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–300 / 300) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–320 / 240) ppm
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (255-byte packets) > (–125 / 100) ppm
Co-channel rejection(1) Wanted signal at –79 dBm, modulated interferer in channel, BER = 10–3 –1.5 dB
Selectivity, ±1 MHz(1) Wanted signal at –79 dBm, modulated interferer at ±1 MHz, BER = 10–3 8 / 4.5(2) dB
Selectivity, ±2 MHz(1) Wanted signal at –79 dBm, modulated interferer at ±2 MHz, BER = 10–3  44 / 37(2) dB
Selectivity, ±3 MHz(1) Wanted signal at –79 dBm, modulated interferer at ±3 MHz, BER = 10–3 46 / 44(2) dB
Selectivity, ±4 MHz(1) Wanted signal at –79 dBm, modulated interferer at ±4 MHz, BER = 10–3 44 / 46(2) dB
Selectivity, ±6 MHz(1) Wanted signal at –79 dBm, modulated interferer at ≥ ±6 MHz, BER = 10–3 48 / 44(2) dB
Selectivity, ±7 MHz Wanted signal at –79 dBm, modulated interferer at ≥ ±7 MHz, BER = 10–3 51 / 45(2) dB
Selectivity, Image frequency(1) Wanted signal at –79 dBm, modulated interferer at image frequency, BER = 10–3 37 dB
Selectivity, Image frequency ±1 MHz(1) Note that Image frequency + 1 MHz is the Co- channel –1 MHz. Wanted signal at –79 dBm, modulated interferer at ±1 MHz from image frequency, BER = 10–3 4.5 / 44 (2) dB
RSSI Range 89 dB
RSSI Accuracy (+/-) ±4 dB
500 kbps (LE Coded)
Receiver sensitivity Differential mode. BER = 10–3 –100 dBm
Receiver saturation Differential mode. BER = 10–3 > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–300 / 300) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–450 / 450) ppm
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (255-byte packets) > (–150 / 175) ppm
Co-channel rejection(1) Wanted signal at –72 dBm, modulated interferer in channel, BER = 10–3 –3.5 dB
Selectivity, ±1 MHz(1) Wanted signal at –72 dBm, modulated interferer at ±1 MHz, BER = 10–3 8 / 4(2) dB
Selectivity, ±2 MHz(1) Wanted signal at –72 dBm, modulated interferer at ±2 MHz, BER = 10–3 43 / 35(2) dB
Selectivity, ±3 MHz(1) Wanted signal at –72 dBm, modulated interferer at ±3 MHz, BER = 10–3 46 / 46(2) dB
Selectivity, ±4 MHz(1) Wanted signal at –72 dBm, modulated interferer at ±4 MHz, BER = 10–3 45 / 47(2) dB
Selectivity, ±6 MHz(1) Wanted signal at –72 dBm, modulated interferer at ≥ ±6 MHz, BER = 10–3 46 / 45(2) dB
Selectivity, ±7 MHz Wanted signal at –72 dBm, modulated interferer at ≥ ±7 MHz, BER = 10–3 49 / 45(2) dB
Selectivity, Image frequency(1) Wanted signal at –72 dBm, modulated interferer at image frequency, BER = 10–3 35 dB
Selectivity, Image frequency ±1 MHz(1) Note that Image frequency + 1 MHz is the Co- channel –1 MHz. Wanted signal at –72 dBm, modulated interferer at ±1 MHz from image frequency, BER = 10–3 4 / 46(2) dB
RSSI Range 90 dB
RSSI Accuracy (+/-) ±4 dB
1 Mbps (LE 1M)
Receiver sensitivity Differential mode. BER = 10–3 –97 dBm
Receiver saturation Differential mode. BER = 10–3  > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–350 / 350) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–650 / 750) ppm
Co-channel rejection(1) Wanted signal at –67 dBm, modulated interferer in channel, BER = 10–3 –6 dB
Selectivity, ±1 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±1 MHz, BER = 10–3 7 / 4(2) dB
Selectivity, ±2 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±2 MHz,BER = 10–3 39 / 33(2) dB
Selectivity, ±3 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±3 MHz, BER = 10–3 36 / 40(2) dB
Selectivity, ±4 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±4 MHz, BER = 10–3 36 / 45(2) dB
Selectivity, ±5 MHz or more(1) Wanted signal at –67 dBm, modulated interferer at ≥ ±5 MHz, BER = 10–3 40 dB
Selectivity, image frequency(1) Wanted signal at –67 dBm, modulated interferer at image frequency, BER = 10–3 33 dB
Selectivity, image frequency
±1 MHz(1)		 Note that Image frequency + 1 MHz is the Co- channel –1 MHz. Wanted signal at –67 dBm, modulated interferer at ±1 MHz from image frequency, BER = 10–3 4 / 41(2) dB
Out-of-band blocking(3) 30 MHz to 2000 MHz –10 dBm
Out-of-band blocking 2003 MHz to 2399 MHz –18 dBm
Out-of-band blocking 2484 MHz to 2997 MHz –12 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz –2 dBm
Intermodulation Wanted signal at 2402 MHz, –64 dBm. Two interferers at 2405 and 2408 MHz respectively, at the given power level  –42 dBm
Spurious emissions,
30 to 1000 MHz		 Measurement in a 50-Ω single-ended load. < –59 dBm
Spurious emissions,
1 to 12.75 GHz		 Measurement in a 50-Ω single-ended load. < –47 dBm
RSSI dynamic range 70 dB
RSSI accuracy ±4 dB
2 Mbps (LE 2M)
Receiver sensitivity Differential mode. Measured at SMA connector, BER = 10–3  –91 dBm
Receiver saturation Differential mode. Measured at SMA connector, BER = 10–3 > 5 dBm
Frequency error tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency > (–500 / 500) kHz
Data rate error tolerance Difference between incoming data rate and the internally generated data rate (37-byte packets) > (–700 / 750) ppm
Co-channel rejection(1) Wanted signal at –67 dBm, modulated interferer in channel,BER = 10–3 –7 dB
Selectivity, ±2 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±2 MHz, Image frequency is at –2 MHz, BER = 10–3 8 / 4(2) dB
Selectivity, ±4 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±4 MHz, BER = 10–3 36 / 34(2) dB
Selectivity, ±6 MHz(1) Wanted signal at –67 dBm, modulated interferer at ±6 MHz, BER = 10–3 37 / 36(2) dB
Selectivity, image frequency(1) Wanted signal at –67 dBm, modulated interferer at image frequency, BER = 10–3 4 dB
Selectivity, image frequency
±2 MHz(1)		 Note that Image frequency + 2 MHz is the Co-channel. Wanted signal at –67 dBm, modulated interferer at ±2 MHz from image frequency, BER = 10–3 –7 / 36(2) dB
Out-of-band blocking(3) 30 MHz to 2000 MHz –16 dBm
Out-of-band blocking 2003 MHz to 2399 MHz –21 dBm
Out-of-band blocking 2484 MHz to 2997 MHz –15 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz –12 dBm
Intermodulation Wanted signal at 2402 MHz, –64 dBm. Two interferers at 2408 and 2414 MHz respectively, at the given power level –38 dBm
RSSI Range 60 dB
RSSI Accuracy (+/-) ±4 dB
(1) Numbers given as I/C dB
(2) X / Y, where X is +N MHz and Y is –N MHz
(3) Excluding one exception at Fwanted / 2, per Bluetooth Specification