SLVSGH7B november   2022  – july 2023 DRV8410

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Diagrams
  9. 8 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 External Components
    4. 9.4 Feature Description
      1. 9.4.1 Bridge Control
        1. 9.4.1.1 Parallel Bridge Interface
      2. 9.4.2 Current Regulation
      3. 9.4.3 Protection Circuits
        1. 9.4.3.1 Overcurrent Protection (OCP)
        2. 9.4.3.2 Thermal Shutdown (TSD)
        3. 9.4.3.3 Undervoltage Lockout (UVLO)
    5. 9.5 Device Functional Modes
      1. 9.5.1 Active Mode
      2. 9.5.2 Low-Power Sleep Mode
      3. 9.5.3 Fault Mode
    6. 9.6 Pin Diagrams
      1. 9.6.1 Logic-Level Inputs
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Typical Application
        1. 10.1.1.1 Stepper Motor Application
          1. 10.1.1.1.1 Design Requirements
          2. 10.1.1.1.2 Detailed Design Procedure
            1. 10.1.1.1.2.1 Stepper Motor Speed
            2. 10.1.1.1.2.2 Current Regulation
            3. 10.1.1.1.2.3 Stepping Modes
              1. 10.1.1.1.2.3.1 Full-Stepping Operation
              2. 10.1.1.1.2.3.2 Half-Stepping Operation with Fast Decay
              3. 10.1.1.1.2.3.3 Half-Stepping Operation with Slow Decay
          3. 10.1.1.1.3 Application Curves
        2. 10.1.1.2 Dual BDC Motor Application
          1. 10.1.1.2.1 Design Requirements
          2. 10.1.1.2.2 Detailed Design Procedure
            1. 10.1.1.2.2.1 Motor Voltage
            2. 10.1.1.2.2.2 Current Regulation
            3. 10.1.1.2.2.3 Sense Resistor
          3. 10.1.1.2.3 Application Curves
        3. 10.1.1.3 Thermal Considerations
          1. 10.1.1.3.1 Maximum Output Current
          2. 10.1.1.3.2 Power Dissipation
          3. 10.1.1.3.3 Thermal Performance
            1. 10.1.1.3.3.1 Steady-State Thermal Performance
            2. 10.1.1.3.3.2 Transient Thermal Performance
        4. 10.1.1.4 Multi-Sourcing with Standard Motor Driver Pinout
  12. 11Power Supply Recommendations
    1. 11.1 Bulk Capacitance
    2. 11.2 Power Supply and Logic Sequencing
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Community Resources
    4. 13.4 Trademarks
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • PWP|16
  • RTE|16
Thermal pad, mechanical data (Package|Pins)
Orderable Information

12.1 Layout Guidelines

Since the DRV8410 device has integrated power MOSFETs capable of driving high current, careful attention should be paid to the layout design and external component placement. Some design and layout guidelines are provided below. For more information on layout recommendations, please see the application note Best Practices for Board Layout of Motor Drivers.

  • Low ESR ceramic capacitors should be utilized for the VM-to-GND. X5R and X7R types are recommended.
  • The VM power supply capacitor should be placed as close to the device as possible to minimize the loop inductance.
  • The VM power supply bulk capacitor can be of ceramic or electrolytic type, but should also be placed as close as possible to the device to minimize the loop inductance.
  • VM, xOUTx, and GND pins carry the high current from the power supply to the outputs and back to ground. Thick metal routing should be utilized for these traces as is feasible.
  • GND should connect directly on the PCB ground plane.
  • The device thermal pad should be attached to the PCB top layer ground plane and internal ground plane (when available) through thermal vias to maximize the PCB heat sinking.
  • The copper plane area attached to the thermal pad should be maximized to ensure optimal heat sinking.