SNVSBK2 September   2019 LP8733

PRODUCTION DATA.  

  1. 1 Features
    1.     Simplified Schematic
  2. 2 Applications
  3. 3 Description
    1.     DC/DC Efficiency vs Output Current
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Serial Bus Timing Parameters
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  DC/DC Converters
        1. 7.3.1.1 Overview
        2. 7.3.1.2 Dual-Phase Operation and Phase-Adding/Shedding
        3. 7.3.1.3 Transition Between PWM and PFM Modes
        4. 7.3.1.4 Dual-Phase Switcher Configurations
        5. 7.3.1.5 Buck Converter Load Current Measurement
        6. 7.3.1.6 Spread-Spectrum Mode
      2. 7.3.2  Sync Clock Functionality
      3. 7.3.3  Low-Dropout Linear Regulators (LDOs)
      4. 7.3.4  Power-Up
      5. 7.3.5  Regulator Control
        1. 7.3.5.1 Enabling and Disabling Regulators
        2. 7.3.5.2 Changing Output Voltage
      6. 7.3.6  Enable and Disable Sequences
      7. 7.3.7  Device Reset Scenarios
      8. 7.3.8  Diagnosis and Protection Features
        1. 7.3.8.1 Power-Good Information (PGOOD pin)
          1. 7.3.8.1.1 PGOOD Pin Gated Mode
          2. 7.3.8.1.2 PGOOD Pin Continuous Mode
        2. 7.3.8.2 Warnings for Diagnosis (Interrupt)
          1. 7.3.8.2.1 Output Power Limit
          2. 7.3.8.2.2 Thermal Warning
        3. 7.3.8.3 Protection (Regulator Disable)
          1. 7.3.8.3.1 Short-Circuit and Overload Protection
          2. 7.3.8.3.2 Overvoltage Protection
          3. 7.3.8.3.3 Thermal Shutdown
        4. 7.3.8.4 Fault (Power Down)
          1. 7.3.8.4.1 Undervoltage Lockout
      9. 7.3.9  Operation of the GPO Signals
      10. 7.3.10 Digital Signal Filtering
    4. 7.4 Device Functional Modes
      1. 7.4.1 Modes of Operation
    5. 7.5 Programming
      1. 7.5.1 I2C-Compatible Interface
        1. 7.5.1.1 Data Validity
        2. 7.5.1.2 Start and Stop Conditions
        3. 7.5.1.3 Transferring Data
        4. 7.5.1.4 I2C-Compatible Chip Address
        5. 7.5.1.5 Auto-Increment Feature
    6. 7.6 Register Maps
      1. 7.6.1 Register Descriptions
        1. 7.6.1.1  DEV_REV
          1. Table 8. DEV_REV Register Field Descriptions
        2. 7.6.1.2  OTP_REV
          1. Table 9. OTP_REV Register Field Descriptions
        3. 7.6.1.3  BUCK0_CTRL_1
          1. Table 10. BUCK0_CTRL_1 Register Field Descriptions
        4. 7.6.1.4  BUCK0_CTRL_2
          1. Table 11. BUCK0_CTRL_2 Register Field Descriptions
        5. 7.6.1.5  BUCK1_CTRL_1
          1. Table 12. BUCK1_CTRL_1 Register Field Descriptions
        6. 7.6.1.6  BUCK1_CTRL_2
          1. Table 13. BUCK1_CTRL_2 Register Field Descriptions
        7. 7.6.1.7  BUCK0_VOUT
          1. Table 14. BUCK0_VOUT Register Field Descriptions
        8. 7.6.1.8  BUCK1_VOUT
          1. Table 15. BUCK1_VOUT Register Field Descriptions
        9. 7.6.1.9  LDO0_CTRL
          1. Table 16. LDO0_CTRL Register Field Descriptions
        10. 7.6.1.10 LDO1_CTRL
          1. Table 17. LDO1_CTRL Register Field Descriptions
        11. 7.6.1.11 LDO0_VOUT
          1. Table 18. LDO0_VOUT Register Field Descriptions
        12. 7.6.1.12 LDO1_VOUT
          1. Table 19. LDO1_VOUT Register Field Descriptions
        13. 7.6.1.13 BUCK0_DELAY
          1. Table 20. BUCK0_DELAY Register Field Descriptions
        14. 7.6.1.14 BUCK1_DELAY
          1. Table 21. BUCK1_DELAY Register Field Descriptions
        15. 7.6.1.15 LDO0_DELAY
          1. Table 22. LDO0_DELAY Register Field Descriptions
        16. 7.6.1.16 LDO1_DELAY
          1. Table 23. LDO1_DELAY Register Field Descriptions
        17. 7.6.1.17 GPO_DELAY
          1. Table 24. GPO_DELAY Register Field Descriptions
        18. 7.6.1.18 GPO2_DELAY
          1. Table 25. GPO2_DELAY Register Field Descriptions
        19. 7.6.1.19 GPO_CTRL
          1. Table 26. GPO_CTRL Register Field Descriptions
        20. 7.6.1.20 CONFIG
          1. Table 27. CONFIG Register Field Descriptions
        21. 7.6.1.21 PLL_CTRL
          1. Table 28. PLL_CTRL Register Field Descriptions
        22. 7.6.1.22 PGOOD_CTRL_1
          1. Table 29. PGOOD_CTRL_1 Register Field Descriptions
        23. 7.6.1.23 PGOOD_CTRL_2
          1. Table 30. PGOOD_CTRL_2 Register Field Descriptions
        24. 7.6.1.24 PG_FAULT
          1. Table 31. PG_FAULT Register Field Descriptions
        25. 7.6.1.25 RESET
          1. Table 32. RESET Register Field Descriptions
        26. 7.6.1.26 INT_TOP_1
          1. Table 33. INT_TOP_1 Register Field Descriptions
        27. 7.6.1.27 INT_TOP_2
          1. Table 34. INT_TOP_2 Register Field Descriptions
        28. 7.6.1.28 INT_BUCK
          1. Table 35. INT_BUCK Register Field Descriptions
        29. 7.6.1.29 INT_LDO
          1. Table 36. INT_LDO Register Field Descriptions
        30. 7.6.1.30 TOP_STAT
          1. Table 37. TOP_STAT Register Field Descriptions
        31. 7.6.1.31 BUCK_STAT
          1. Table 38. BUCK_STAT Register Field Descriptions
        32. 7.6.1.32 LDO_STAT
          1. Table 39. LDO_STAT Register Field Descriptions
        33. 7.6.1.33 TOP_MASK_1
          1. Table 40. TOP_MASK_1 Register Field Descriptions
        34. 7.6.1.34 TOP_MASK_2
          1. Table 41. TOP_MASK_2 Register Field Descriptions
        35. 7.6.1.35 BUCK_MASK
          1. Table 42. BUCK_MASK Register Field Descriptions
        36. 7.6.1.36 LDO_MASK
          1. Table 43. LDO_MASK Register Field Descriptions
        37. 7.6.1.37 SEL_I_LOAD
          1. Table 44. SEL_I_LOAD Register Field Descriptions
        38. 7.6.1.38 I_LOAD_2
          1. Table 45. I_LOAD_2 Register Field Descriptions
        39. 7.6.1.39 I_LOAD_1
          1. Table 46. I_LOAD_1 Register Field Descriptions
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Design Requirements
        1. 8.2.1.1 Inductor Selection
        2. 8.2.1.2 Buck Input Capacitor Selection
        3. 8.2.1.3 Buck Output Capacitor Selection
        4. 8.2.1.4 LDO Input Capacitor Selection
        5. 8.2.1.5 LDO Output Capacitor Selection
        6. 8.2.1.6 Current Limit vs. Maximum Output Current
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.2.1.5 LDO Output Capacitor Selection

The output capacitors COUT_LDO0 and COUT_LDO1 are shown in the Typical Applications. A ceramic output capacitor of minimum 1.0 μF is required. Place the output capacitor as close to the VOUT_LDOx pin and AGND pin of the device as possible. Use X7R type of capacitors, not Y5V or F. DC bias characteristics of capacitors must be considered, the minimum effective output capacitance to ensure good performance is 0.4 μF per LDO input at maximum input voltage including tolerances, ambient temperature range, and aging. See Table 51.

The output capacitance must be smaller than the input capacitance to ensure the stability of the LDO. With a 1-μF output capacitor, TI recommends using at least a 2.2-μF input capacitor; with a 2.2-μF output capacitor at least 4.7-μF input capacitance.

The VANA input is used to supply analog and digital circuits in the device. See Table 52 for recommended components from for VANA input supply filtering.

Table 51. Recommended LDO Output Capacitors (X7R Dielectric)

MANUFACTURER PART NUMBER VALUE CASE SIZE DIMENSIONS L × W × H (mm) VOLTAGE RATING
Murata GCM188R71C105KA64 1 µF (10%) 0603 1.6 × 0.8 × 0.8 16 V
Murata GCM188R70J225KE22 2.2 µF (10%) 0603 1.6 × 0.8 × 0.8 6.3 V

Table 52. Recommended Supply Filtering Components

MANUFACTURER PART NUMBER VALUE CASE SIZE DIMENSIONS L × W × H (mm) VOLTAGE RATING
Murata GCM155R71C104KA55 100 nF (10%) 0402 1 × 0.5 × 0.5 16 V
Murata GCM188R71C104KA37 100 nF (10%) 0603 1.6 × 0.8 × 0.8 16 V