SBOSAA5B April   2022  – September 2022 OPA2675

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Family Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: Full Bias and Offline Mode VS = ±6 V
    6. 7.6  Electrical Characteristics: 75% Bias Mode VS = ±6 V
    7. 7.7  Electrical Characteristics: 50% Bias Mode VS = ±6 V
    8. 7.8  Electrical Characteristics: DIfferential Output  VS = 12 V
    9. 7.9  Electrical Characteristics: VS = 5 V
    10. 7.10 Typical Characteristics: VS = ±6 V, Full Bias
    11. 7.11 Typical Characteristics: VS = ±6 V Differential, Full Bias
    12. 7.12 Typical Characteristics: VS = ±6 V, 75% Bias
    13. 7.13 Typical Characteristics: VS = ±6 V, 50% Bias
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Operating Suggestions
        1. 8.3.1.1 Setting Resistor Values to Optimize Bandwidth
        2. 8.3.1.2 Output Current and Voltage
        3. 8.3.1.3 Driving Capacitive Loads
        4. 8.3.1.4 Line Driver Headroom Model
        5. 8.3.1.5 Noise Performance
    4. 8.4 Device Functional Modes
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 High-Speed Active Filters
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Thermal Analysis
    2. 10.2 Input and ESD Protection
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Voltage Supply voltage, VS = (VS+) – (VS–)(2) 14 V
Bias control pin voltage, referenced to GND 0 VS- + 14
All pins except VS+, VS– and Bias control pins VS– – 0.5 VS+ + 0.5
GND Pin VS– – 0.5 VS+ + 0.5
Output pin: Offline mode ±4.5
Inverting input pin: Offline mode ±1.1
Differential input voltage (each amplifier) ±2
Current All input pins, current limit ±10 mA
Continuous power dissipation See Thermal Information
Temperature Continuous operating junction temperature(3) 139 °C
Maximum junction, TJ (under any condition)(5) 150
Storage, Tstg –65 150
Operation outside the Absolute Maximum Rating may cause permanent device damage. Absolute maximum ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Condition. If briefly operating outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not sustain damage, but it may not be fully functional. Operating the device in this manner may affect device reliability, functionality, performance, and shorten the device lifetime.
Refer to Breakdown Test.
The absolute maximum junction temperature for continuous operation is limited by the package constraints. Operation above this temperature can result in reduced reliability and/or lifetime of the device. The device has thermal protection that shuts down the device at approximately 180°C junction temperature and recovery at approximately 160°C.