SCPS124H September   2006  – March 2021 PCA9534

PRODUCTION DATA  

  1. 1 Features
  2. 2 Description
  3. 3 Revision History
  4. 4 Description (Continued)
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Resistance Characteristics
    5. 7.5 Electrical Characteristics
    6. 7.6 I2C Interface Timing Requirements
    7. 7.7 Switching Characteristics
    8. 7.8 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Functional Block Diagram
    2. 9.2 Device Functional Modes
      1. 9.2.1 Power-On Reset
      2. 9.2.2 I/O Port
      3. 9.2.3 Interrupt Output ( INT)
        1. 9.2.3.1 Interrupt Errata
          1. 9.2.3.1.1 Description
          2. 9.2.3.1.2 System Impact
          3. 9.2.3.1.3 System Workaround
    3. 9.3 Programming
      1. 9.3.1 I2C Interface
      2. 9.3.2 Register Map
        1. 9.3.2.1 Device Address
        2. 9.3.2.2 Control Register And Command Byte
        3. 9.3.2.3 Register Descriptions
        4. 9.3.2.4 Bus Transactions
          1. 9.3.2.4.1 Writes
          2. 9.3.2.4.2 Reads
  10. 10Application Information Disclaimer
    1. 10.1 Application Information
      1. 10.1.1 Typical Application
        1. 10.1.1.1 Design Requirements
          1. 10.1.1.1.1 Minimizing ICC When The I/O Controls Leds
  11. 11Power Supply Recommendations
    1. 11.1 Power-On Reset Requirements
  12. 12Device and Documentation Support
    1. 12.1 Receiving Notification of Documentation Updates
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

3 Revision History

Changes from Revision G (May 2014) to Revision H (March 2021)

  • Moved the "Storage temperature range" to the Absolute Maximum Ratings Go
  • Moved the "Package thermal impedance" to the Thermal Resistance Characteristic Go
  • Changed the VIH High-level input voltage (SDL, SDA) Max value From: 5.5 V To: VCC in the Recommended Operating Conditions Go
  • Changed the VIH High-level input voltage (A0, A1, A2, P7–P0) MIN value From: 2 V To: VCC in the Recommended Operating Conditions Go
  • Changed the VIL Low-level input voltage (A0, A1, A2, P7–P0) MAX value From: 0.8 V To: 0.3 x VCC in the Recommended Operating Conditions Go
  • Added the Thermal Resistance Characteristics Go
  • Changed the VPORR row in the Electrical Characteristics Go
  • Added the VPORF row in the Electrical Characteristics Go
  • Changed the ICC Standby mode values in the Electrical Characteristics Go
  • Changed the ΔICC Additional current in standby mode (5.5 V) mAX value From: 1 mA To: 4 mA in the Electrical Characteristics Go
  • Changed the Ci SCL Max value From: 5 pF To: 8 pF in the Electrical Characteristics Go
  • Changed the Cio SDA Max value From:6.5 pF To: 9.5 pF in the Electrical Characteristics Go
  • Changed the tpv Output data valid MAX values From: 200 ns To 350 ns in the Swirtching Characteristics Go
  • Changed the Typical Characteristics graphsGo
  • Changed the Power Supply Recommendations Go

Changes from Revision F (June 2010) to Revision G (June 2014)

  • Added Interrupt Errata section.Go