SPRS797C November   2012  – October 2018 TMS320F28050 , TMS320F28051 , TMS320F28052 , TMS320F28053 , TMS320F28054 , TMS320F28055

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagram
    2. 4.2 Signal Descriptions
      1. Table 4-1 Signal Descriptions
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Power Consumption Summary
      1. Table 5-1 TMS320F2805x Current Consumption at 60-MHz SYSCLKOUT
      2. 5.4.1     Reducing Current Consumption
      3. 5.4.2     Current Consumption Graphs (VREG Enabled)
    5. 5.5  Electrical Characteristics
    6. 5.6  Thermal Resistance Characteristics for PN Package
    7. 5.7  Thermal Design Considerations
    8. 5.8  Emulator Connection Without Signal Buffering for the MCU
    9. 5.9  Parameter Information
      1. 5.9.1 Timing Parameter Symbology
      2. 5.9.2 General Notes on Timing Parameters
    10. 5.10 Test Load Circuit
    11. 5.11 Power Sequencing
      1. Table 5-3 Reset (XRS) Timing Requirements
      2. Table 5-4 Reset (XRS) Switching Characteristics
    12. 5.12 Clock Specifications
      1. 5.12.1 Device Clock Table
        1. Table 5-5 2805x Clock Table and Nomenclature (60-MHz Devices)
        2. Table 5-6 Device Clocking Requirements/Characteristics
        3. Table 5-7 Internal Zero-Pin Oscillator (INTOSC1, INTOSC2) Characteristics
      2. 5.12.2 Clock Requirements and Characteristics
        1. Table 5-8  XCLKIN Timing Requirements - PLL Enabled
        2. Table 5-9  XCLKIN Timing Requirements - PLL Disabled
        3. Table 5-10 XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
    13. 5.13 Flash Timing
      1. Table 5-11 Flash/OTP Endurance for T Temperature Material
      2. Table 5-12 Flash/OTP Endurance for S Temperature Material
      3. Table 5-13 Flash/OTP Endurance for Q Temperature Material
      4. Table 5-14 Flash Parameters at 60-MHz SYSCLKOUT
      5. Table 5-15 Flash/OTP Access Timing
      6. Table 5-16 Flash Data Retention Duration
  6. 6Detailed Description
    1. 6.1 Overview
      1. 6.1.1  CPU
      2. 6.1.2  Control Law Accelerator
      3. 6.1.3  Memory Bus (Harvard Bus Architecture)
      4. 6.1.4  Peripheral Bus
      5. 6.1.5  Real-Time JTAG and Analysis
      6. 6.1.6  Flash
      7. 6.1.7  M0, M1 SARAMs
      8. 6.1.8  L0 SARAM, and L1, L2, and L3 DPSARAMs
      9. 6.1.9  Boot ROM
        1. 6.1.9.1 Emulation Boot
        2. 6.1.9.2 GetMode
        3. 6.1.9.3 Peripheral Pins Used by the Bootloader
      10. 6.1.10 Security
      11. 6.1.11 Peripheral Interrupt Expansion Block
      12. 6.1.12 External Interrupts (XINT1 to XINT3)
      13. 6.1.13 Internal Zero-Pin Oscillators, Oscillator, and PLL
      14. 6.1.14 Watchdog
      15. 6.1.15 Peripheral Clocking
      16. 6.1.16 Low-power Modes
      17. 6.1.17 Peripheral Frames 0, 1, 2, 3 (PFn)
      18. 6.1.18 General-Purpose Input/Output Multiplexer
      19. 6.1.19 32-Bit CPU-Timers (0, 1, 2)
      20. 6.1.20 Control Peripherals
      21. 6.1.21 Serial Port Peripherals
    2. 6.2 Memory Maps
    3. 6.3 Register Map
    4. 6.4 Device Emulation Registers
    5. 6.5 VREG, BOR, POR
      1. 6.5.1 On-chip VREG
        1. 6.5.1.1 Using the On-chip VREG
        2. 6.5.1.2 Disabling the On-chip VREG
      2. 6.5.2 On-chip Power-On Reset and Brownout Reset Circuit
    6. 6.6 System Control
      1. 6.6.1 Internal Zero-Pin Oscillators
      2. 6.6.2 Crystal Oscillator Option
      3. 6.6.3 PLL-Based Clock Module
      4. 6.6.4 Loss of Input Clock (NMI-watchdog Function)
      5. 6.6.5 CPU-watchdog Module
    7. 6.7 Low-power Modes Block
    8. 6.8 Interrupts
      1. 6.8.1 External Interrupts
        1. 6.8.1.1 External Interrupt Electrical Data/Timing
          1. Table 6-26 External Interrupt Timing Requirements
          2. Table 6-27 External Interrupt Switching Characteristics
    9. 6.9 Peripherals
      1. 6.9.1  Control Law Accelerator
        1. 6.9.1.1 CLA Device-Specific Information
        2. 6.9.1.2 CLA Register Descriptions
      2. 6.9.2  Analog Block
        1. 6.9.2.1 Analog-to-Digital Converter
          1. 6.9.2.1.1 ADC Device-Specific Information
          2. 6.9.2.1.2 ADC Electrical Data/Timing
            1. Table 6-32  ADC Electrical Characteristics
            2. Table 6-34  ADC Power Modes
            3. 6.9.2.1.2.1 External ADC Start-of-Conversion Electrical Data/Timing
              1. Table 6-35 External ADC Start-of-Conversion Switching Characteristics
            4. 6.9.2.1.2.2 Internal Temperature Sensor
              1. Table 6-36 Temperature Sensor Coefficient
            5. 6.9.2.1.2.3 ADC Power-Up Control Bit Timing
              1. Table 6-37 ADC Power-Up Delays
            6. 6.9.2.1.2.4 ADC Sequential and Simultaneous Timings
        2. 6.9.2.2 Analog Front End
          1. 6.9.2.2.1 AFE Device-Specific Information
          2. 6.9.2.2.2 AFE Register Descriptions
          3. 6.9.2.2.3 PGA Electrical Data/Timing
          4. 6.9.2.2.4 Comparator Block Electrical Data/Timing
            1. Table 6-45 Electrical Characteristics of the Comparator/DAC
          5. 6.9.2.2.5 VREFOUT Buffered DAC Electrical Data
            1. Table 6-46 Electrical Characteristics of VREFOUT Buffered DAC
      3. 6.9.3  Detailed Descriptions
      4. 6.9.4  Serial Peripheral Interface
        1. 6.9.4.1 SPI Device-Specific Information
        2. 6.9.4.2 SPI Register Descriptions
        3. 6.9.4.3 SPI Master Mode Electrical Data/Timing
          1. Table 6-48 SPI Master Mode External Timing (Clock Phase = 0)
          2. Table 6-49 SPI Master Mode External Timing (Clock Phase = 1)
        4. 6.9.4.4 SPI Slave Mode Electrical Data/Timing
          1. Table 6-50 SPI Slave Mode External Timing (Clock Phase = 0)
          2. Table 6-51 SPI Slave Mode External Timing (Clock Phase = 1)
      5. 6.9.5  Serial Communications Interface
        1. 6.9.5.1 SCI Device-Specific Information
        2. 6.9.5.2 SCI Register Descriptions
      6. 6.9.6  Enhanced Controller Area Network
        1. 6.9.6.1 eCAN Device-Specific Information
        2. 6.9.6.2 eCAN Register Descriptions
      7. 6.9.7  Inter-Integrated Circuit
        1. 6.9.7.1 I2C Device-Specific Information
        2. 6.9.7.2 I2C Register Descriptions
        3. 6.9.7.3 I2C Electrical Data/Timing
          1. Table 6-58 I2C Timing Requirements
          2. Table 6-59 I2C Switching Characteristics
      8. 6.9.8  Enhanced Pulse Width Modulator
        1. 6.9.8.1 ePWM Device-Specific Information
        2. 6.9.8.2 ePWM Register Descriptions
        3. 6.9.8.3 ePWM Electrical Data/Timing
          1. Table 6-62 ePWM Timing Requirements
          2. Table 6-63 ePWM Switching Characteristics
          3. 6.9.8.3.1  Trip-Zone Input Timing
            1. Table 6-64 Trip-Zone Input Timing Requirements
      9. 6.9.9  Enhanced Capture Module
        1. 6.9.9.1 eCAP Module Device-Specific Information
        2. 6.9.9.2 eCAP Module Register Descriptions
        3. 6.9.9.3 eCAP Module Electrical Data/Timing
          1. Table 6-66 eCAP Timing Requirement
          2. Table 6-67 eCAP Switching Characteristics
      10. 6.9.10 Enhanced Quadrature Encoder Pulse
        1. 6.9.10.1 eQEP Device-Specific Information
        2. 6.9.10.2 eQEP Register Descriptions
        3. 6.9.10.3 eQEP Electrical Data/Timing
          1. Table 6-69 eQEP Timing Requirements
          2. Table 6-70 eQEP Switching Characteristics
      11. 6.9.11 JTAG Port
        1. 6.9.11.1 JTAG Port Device-Specific Information
      12. 6.9.12 General-Purpose Input/Output
        1. 6.9.12.1 GPIO Device-Specific Information
        2. 6.9.12.2 GPIO Register Descriptions
        3. 6.9.12.3 GPIO Electrical Data/Timing
          1. 6.9.12.3.1 GPIO - Output Timing
            1. Table 6-74 General-Purpose Output Switching Characteristics
          2. 6.9.12.3.2 GPIO - Input Timing
            1. Table 6-75 General-Purpose Input Timing Requirements
          3. 6.9.12.3.3 Sampling Window Width for Input Signals
          4. 6.9.12.3.4 Low-Power Mode Wakeup Timing
            1. Table 6-76 IDLE Mode Timing Requirements
            2. Table 6-77 IDLE Mode Switching Characteristics
            3. Table 6-78 STANDBY Mode Timing Requirements
            4. Table 6-79 STANDBY Mode Switching Characteristics
            5. Table 6-80 HALT Mode Timing Requirements
            6. Table 6-81 HALT Mode Switching Characteristics
  7. 7Applications, Implementation, and Layout
    1. 7.1 TI Design or Reference Design
  8. 8Device and Documentation Support
    1. 8.1 Getting Started
    2. 8.2 Device and Development Support Tool Nomenclature
    3. 8.3 Tools and Software
    4. 8.4 Documentation Support
    5. 8.5 Related Links
    6. 8.6 Community Resources
    7. 8.7 Trademarks
    8. 8.8 Electrostatic Discharge Caution
    9. 8.9 Glossary
  9. 9Mechanical Packaging and Orderable Information
    1. 9.1 Packaging Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

PLL-Based Clock Module

The devices have an on-chip, PLL-based clock module. This module provides all the necessary clocking signals for the device, as well as control for low-power mode entry. The PLL has a 4-bit ratio control PLLCR[DIV] to select different CPU clock rates. The watchdog module should be disabled before writing to the PLLCR register. The watchdog module can be re-enabled (if needed) after the PLL module has stabilized, which takes 1 ms. The input clock and PLLCR[DIV] bits should be chosen in such a way that the output frequency of the PLL (VCOCLK) is at least 50 MHz.

Table 6-19 PLL Settings

PLLCR[DIV] VALUE(2)(3) SYSCLKOUT (CLKIN)
PLLSTS[DIVSEL] = 0 or 1(1) PLLSTS[DIVSEL] = 2 PLLSTS[DIVSEL] = 3
0000 (PLL bypass) OSCCLK/4 (Default)(2) OSCCLK/2 OSCCLK
0001 (OSCCLK × 1)/4 (OSCCLK × 1)/2 (OSCCLK × 1)/1
0010 (OSCCLK × 2)/4 (OSCCLK × 2)/2 (OSCCLK × 2)/1
0011 (OSCCLK × 3)/4 (OSCCLK × 3)/2 (OSCCLK × 3)/1
0100 (OSCCLK × 4)/4 (OSCCLK × 4)/2 (OSCCLK × 4)/1
0101 (OSCCLK × 5)/4 (OSCCLK × 5)/2 (OSCCLK × 5)/1
0110 (OSCCLK × 6)/4 (OSCCLK × 6)/2 (OSCCLK × 6)/1
0111 (OSCCLK × 7)/4 (OSCCLK × 7)/2 (OSCCLK × 7)/1
1000 (OSCCLK × 8)/4 (OSCCLK × 8)/2 (OSCCLK × 8)/1
1001 (OSCCLK × 9)/4 (OSCCLK × 9)/2 (OSCCLK × 9)/1
1010 (OSCCLK × 10)/4 (OSCCLK × 10)/2 (OSCCLK × 10)/1
1011 (OSCCLK × 11)/4 (OSCCLK × 11)/2 (OSCCLK × 11)/1
1100 (OSCCLK × 12)/4 (OSCCLK × 12)/2 (OSCCLK × 12)/1
By default, PLLSTS[DIVSEL] is configured for /4. (The boot ROM changes the PLLSTS[DIVSEL] configuration to /1.) PLLSTS[DIVSEL] must be 0 before writing to the PLLCR and should be changed only after PLLSTS[PLLLOCKS] = 1.
The PLL control register (PLLCR) and PLL Status Register (PLLSTS) are reset to their default state by the XRS signal or a watchdog reset only. A reset issued by the debugger or the missing clock detect logic has no effect.
This register is EALLOW protected. For more information, see the System Control and Interrupts chapter of the TMS320x2805x Piccolo Technical Reference Manual.

Table 6-20 CLKIN Divide Options

PLLSTS [DIVSEL] CLKIN DIVIDE
0 /4
1 /4
2 /2
3 /1

The PLL-based clock module provides four modes of operation:

  • INTOSC1 (Internal Zero-pin Oscillator 1): INTOSC1 is the on-chip internal oscillator 1. INTOSC1 can provide the clock for the Watchdog block, core and CPU-Timer 2.
  • INTOSC2 (Internal Zero-pin Oscillator 2): INTOSC2 is the on-chip internal oscillator 2. INTOSC2 can provide the clock for the Watchdog block, core and CPU-Timer 2. Both INTOSC1 and INTOSC2 can be independently chosen for the Watchdog block, core and CPU-Timer 2.
  • Crystal/Resonator Operation: The on-chip (crystal) oscillator enables the use of an external crystal/resonator attached to the device to provide the time base. The crystal/resonator is connected to the X1/X2 pins. Some devices may not have the X1/X2 pins. See Table 4-1 for details.
  • External Clock Source Operation: If the on-chip (crystal) oscillator is not used, this mode allows the on-chip (crystal) oscillator to be bypassed. The device clocks are generated from an external clock source input on the XCLKIN pin. The XCLKIN is multiplexed with GPIO19 or GPIO38 pin. The XCLKIN input can be selected as GPIO19 or GPIO38 through the XCLKINSEL bit in XCLK register. The CLKCTL[XCLKINOFF] bit disables this clock input (forced low). If the clock source is not used or the respective pins are used as GPIOs, the user should disable at boot time.

Before changing clock sources, ensure that the target clock is present. If a clock is not present, then that clock source must be disabled (using the CLKCTL register) before switching clocks.

Table 6-21 Possible PLL Configuration Modes

PLL MODE REMARKS PLLSTS[DIVSEL] CLKIN AND
SYSCLKOUT
PLL Off Invoked by the user setting the PLLOFF bit in the PLLSTS register. The PLL block is disabled in this mode. The PLL block being disabled can be useful in reducing system noise and for low-power operation. The PLLCR register must first be set to 0x0000 (PLL Bypass) before entering this mode. The CPU clock (CLKIN) is derived directly from the input clock on either X1/X2, X1 or XCLKIN. 0, 1 OSCCLK/4
2 OSCCLK/2
3 OSCCLK/1
PLL Bypass PLL Bypass is the default PLL configuration upon power-up or after an external reset (XRS). This mode is selected when the PLLCR register is set to 0x0000 or while the PLL locks to a new frequency after the PLLCR register has been modified. In this mode, the PLL is bypassed but is not turned off. 0, 1 OSCCLK/4
2 OSCCLK/2
3 OSCCLK/1
PLL Enable Achieved by writing a nonzero value n into the PLLCR register. Upon writing to the PLLCR the device will switch to PLL Bypass mode until the PLL locks. 0, 1 OSCCLK × n/4
2 OSCCLK × n/2
3 OSCCLK × n/1