SPRS439O June   2007  – April 2019 TMS320F28232 , TMS320F28234 , TMS320F28235 , TMS320F28332 , TMS320F28333 , TMS320F28334 , TMS320F28335

PRODUCTION DATA.  

  1. 1Device Overview
    1. 1.1 Features
    2. 1.2 Applications
    3. 1.3 Description
    4. 1.4 Functional Block Diagram
  2. 2Revision History
  3. 3Device Comparison
    1. 3.1 Related Products
  4. 4Terminal Configuration and Functions
    1. 4.1 Pin Diagrams
    2. 4.2 Signal Descriptions
  5. 5Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings – Automotive
    3. 5.3  ESD Ratings – Commercial
    4. 5.4  Recommended Operating Conditions
    5. 5.5  Power Consumption Summary
      1. Table 5-1 TMS320F28335/F28235 Current Consumption by Power-Supply Pins at 150-MHz SYSCLKOUT
      2. Table 5-2 TMS320F28334/F28234 Current Consumption by Power-Supply Pins at 150-MHz SYSCLKOUT
      3. 5.5.1     Reducing Current Consumption
      4. 5.5.2     Current Consumption Graphs
    6. 5.6  Electrical Characteristics
    7. 5.7  Thermal Resistance Characteristics
      1. 5.7.1 PGF Package
      2. 5.7.2 PTP Package
      3. 5.7.3 ZHH Package
      4. 5.7.4 ZJZ Package
    8. 5.8  Thermal Design Considerations
    9. 5.9  Timing and Switching Characteristics
      1. 5.9.1 Timing Parameter Symbology
        1. 5.9.1.1 General Notes on Timing Parameters
        2. 5.9.1.2 Test Load Circuit
        3. 5.9.1.3 Device Clock Table
          1. Table 5-4 Clocking and Nomenclature (150-MHz Devices)
          2. Table 5-5 Clocking and Nomenclature (100-MHz Devices)
      2. 5.9.2 Power Sequencing
        1. 5.9.2.1   Power Management and Supervisory Circuit Solutions
        2. Table 5-6 Reset (XRS) Timing Requirements
      3. 5.9.3 Clock Requirements and Characteristics
        1. Table 5-7  Input Clock Frequency
        2. Table 5-8  XCLKIN Timing Requirements – PLL Enabled
        3. Table 5-9  XCLKIN Timing Requirements – PLL Disabled
        4. Table 5-10 XCLKOUT Switching Characteristics (PLL Bypassed or Enabled)
      4. 5.9.4 Peripherals
        1. 5.9.4.1 General-Purpose Input/Output (GPIO)
          1. 5.9.4.1.1 GPIO - Output Timing
            1. Table 5-11 General-Purpose Output Switching Characteristics
          2. 5.9.4.1.2 GPIO - Input Timing
            1. Table 5-12 General-Purpose Input Timing Requirements
          3. 5.9.4.1.3 Sampling Window Width for Input Signals
          4. 5.9.4.1.4 Low-Power Mode Wakeup Timing
            1. Table 5-13 IDLE Mode Timing Requirements
            2. Table 5-14 IDLE Mode Switching Characteristics
            3. Table 5-15 STANDBY Mode Timing Requirements
            4. Table 5-16 STANDBY Mode Switching Characteristics
            5. Table 5-17 HALT Mode Timing Requirements
            6. Table 5-18 HALT Mode Switching Characteristics
        2. 5.9.4.2 Enhanced Control Peripherals
          1. 5.9.4.2.1 Enhanced Pulse Width Modulator (ePWM) Timing
            1. Table 5-19 ePWM Timing Requirements
            2. Table 5-20 ePWM Switching Characteristics
          2. 5.9.4.2.2 Trip-Zone Input Timing
            1. Table 5-21 Trip-Zone Input Timing Requirements
          3. 5.9.4.2.3 High-Resolution PWM Timing
            1. Table 5-22 High-Resolution PWM Characteristics at SYSCLKOUT = (60–150 MHz)
          4. 5.9.4.2.4 Enhanced Capture (eCAP) Timing
            1. Table 5-23 Enhanced Capture (eCAP) Timing Requirements
            2. Table 5-24 eCAP Switching Characteristics
          5. 5.9.4.2.5 Enhanced Quadrature Encoder Pulse (eQEP) Timing
            1. Table 5-25 Enhanced Quadrature Encoder Pulse (eQEP) Timing Requirements
            2. Table 5-26 eQEP Switching Characteristics
          6. 5.9.4.2.6 ADC Start-of-Conversion Timing
            1. Table 5-27 External ADC Start-of-Conversion Switching Characteristics
        3. 5.9.4.3 External Interrupt Timing
          1. Table 5-28 External Interrupt Timing Requirements
          2. Table 5-29 External Interrupt Switching Characteristics
        4. 5.9.4.4 I2C Electrical Specification and Timing
          1. Table 5-30 I2C Timing
        5. 5.9.4.5 Serial Peripheral Interface (SPI) Timing
          1. 5.9.4.5.1 Master Mode Timing
            1. Table 5-31 SPI Master Mode External Timing (Clock Phase = 0)
            2. Table 5-32 SPI Master Mode External Timing (Clock Phase = 1)
          2. 5.9.4.5.2 Slave Mode Timing
            1. Table 5-33 SPI Slave Mode External Timing (Clock Phase = 0)
            2. Table 5-34 SPI Slave Mode External Timing (Clock Phase = 1)
        6. 5.9.4.6 Multichannel Buffered Serial Port (McBSP) Timing
          1. 5.9.4.6.1 McBSP Transmit and Receive Timing
            1. Table 5-35 McBSP Timing Requirements
            2. Table 5-36 McBSP Switching Characteristics
          2. 5.9.4.6.2 McBSP as SPI Master or Slave Timing
            1. Table 5-37 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 0)
            2. Table 5-38 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 0)
            3. Table 5-39 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 0)
            4. Table 5-40 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 0)
            5. Table 5-41 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 10b, CLKXP = 1)
            6. Table 5-42 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 10b, CLKXP = 1)
            7. Table 5-43 McBSP as SPI Master or Slave Timing Requirements (CLKSTP = 11b, CLKXP = 1)
            8. Table 5-44 McBSP as SPI Master or Slave Switching Characteristics (CLKSTP = 11b, CLKXP = 1)
      5. 5.9.5 Emulator Connection Without Signal Buffering for the DSP
      6. 5.9.6 External Interface (XINTF) Timing
        1. 5.9.6.1 USEREADY = 0
        2. 5.9.6.2 Synchronous Mode (USEREADY = 1, READYMODE = 0)
        3. 5.9.6.3 Asynchronous Mode (USEREADY = 1, READYMODE = 1)
        4. 5.9.6.4 XINTF Signal Alignment to XCLKOUT
        5. 5.9.6.5 External Interface Read Timing
          1. Table 5-47 External Interface Read Timing Requirements
          2. Table 5-48 External Interface Read Switching Characteristics
        6. 5.9.6.6 External Interface Write Timing
          1. Table 5-49 External Interface Write Switching Characteristics
        7. 5.9.6.7 External Interface Ready-on-Read Timing With One External Wait State
          1. Table 5-50 External Interface Read Switching Characteristics (Ready-on-Read, One Wait State)
          2. Table 5-51 External Interface Read Timing Requirements (Ready-on-Read, One Wait State)
          3. Table 5-52 Synchronous XREADY Timing Requirements (Ready-on-Read, One Wait State)
          4. Table 5-53 Asynchronous XREADY Timing Requirements (Ready-on-Read, One Wait State)
        8. 5.9.6.8 External Interface Ready-on-Write Timing With One External Wait State
          1. Table 5-54 External Interface Write Switching Characteristics (Ready-on-Write, One Wait State)
          2. Table 5-55 Synchronous XREADY Timing Requirements (Ready-on-Write, One Wait State)
          3. Table 5-56 Asynchronous XREADY Timing Requirements (Ready-on-Write, One Wait State)
        9. 5.9.6.9 XHOLD and XHOLDA Timing
          1. Table 5-57 XHOLD/XHOLDA Timing Requirements (XCLKOUT = XTIMCLK)
          2. Table 5-58 XHOLD/XHOLDA Timing Requirements (XCLKOUT = 1/2 XTIMCLK)
      7. 5.9.7 Flash Timing
        1. Table 5-59 Flash Endurance for A and S Temperature Material
        2. Table 5-60 Flash Endurance for Q Temperature Material
        3. Table 5-61 Flash Parameters at 150-MHz SYSCLKOUT
        4. Table 5-62 Flash/OTP Access Timing
        5. Table 5-63 Flash Data Retention Duration
    10. 5.10 On-Chip Analog-to-Digital Converter
      1. Table 5-65 ADC Electrical Characteristics (over recommended operating conditions)
      2. 5.10.1     ADC Power-Up Control Bit Timing
        1. Table 5-66 ADC Power-Up Delays
        2. Table 5-67 Typical Current Consumption for Different ADC Configurations (at 25-MHz ADCCLK)
      3. 5.10.2     Definitions
      4. 5.10.3     Sequential Sampling Mode (Single-Channel) (SMODE = 0)
        1. Table 5-68 Sequential Sampling Mode Timing
      5. 5.10.4     Simultaneous Sampling Mode (Dual-Channel) (SMODE = 1)
        1. Table 5-69 Simultaneous Sampling Mode Timing
      6. 5.10.5     Detailed Descriptions
    11. 5.11 Migrating Between F2833x Devices and F2823x Devices
  6. 6Detailed Description
    1. 6.1 Brief Descriptions
      1. 6.1.1  C28x CPU
      2. 6.1.2  Memory Bus (Harvard Bus Architecture)
      3. 6.1.3  Peripheral Bus
      4. 6.1.4  Real-Time JTAG and Analysis
      5. 6.1.5  External Interface (XINTF)
      6. 6.1.6  Flash
      7. 6.1.7  M0, M1 SARAMs
      8. 6.1.8  L0, L1, L2, L3, L4, L5, L6, L7 SARAMs
      9. 6.1.9  Boot ROM
        1. 6.1.9.1 Peripheral Pins Used by the Bootloader
      10. 6.1.10 Security
      11. 6.1.11 Peripheral Interrupt Expansion (PIE) Block
      12. 6.1.12 External Interrupts (XINT1–XINT7, XNMI)
      13. 6.1.13 Oscillator and PLL
      14. 6.1.14 Watchdog
      15. 6.1.15 Peripheral Clocking
      16. 6.1.16 Low-Power Modes
      17. 6.1.17 Peripheral Frames 0, 1, 2, 3 (PFn)
      18. 6.1.18 General-Purpose Input/Output (GPIO) Multiplexer
      19. 6.1.19 32-Bit CPU-Timers (0, 1, 2)
      20. 6.1.20 Control Peripherals
      21. 6.1.21 Serial Port Peripherals
    2. 6.2 Peripherals
      1. 6.2.1  DMA Overview
      2. 6.2.2  32-Bit CPU-Timer 0, CPU-Timer 1, CPU-Timer 2
      3. 6.2.3  Enhanced PWM Modules
      4. 6.2.4  High-Resolution PWM (HRPWM)
      5. 6.2.5  Enhanced CAP Modules
      6. 6.2.6  Enhanced QEP Modules
      7. 6.2.7  Analog-to-Digital Converter (ADC) Module
        1. 6.2.7.1 ADC Connections if the ADC Is Not Used
        2. 6.2.7.2 ADC Registers
        3. 6.2.7.3 ADC Calibration
      8. 6.2.8  Multichannel Buffered Serial Port (McBSP) Module
      9. 6.2.9  Enhanced Controller Area Network (eCAN) Modules (eCAN-A and eCAN-B)
      10. 6.2.10 Serial Communications Interface (SCI) Modules (SCI-A, SCI-B, SCI-C)
      11. 6.2.11 Serial Peripheral Interface (SPI) Module (SPI-A)
      12. 6.2.12 Inter-Integrated Circuit (I2C)
      13. 6.2.13 GPIO MUX
      14. 6.2.14 External Interface (XINTF)
    3. 6.3 Memory Maps
    4. 6.4 Register Map
      1. 6.4.1 Device Emulation Registers
    5. 6.5 Interrupts
      1. 6.5.1 External Interrupts
    6. 6.6 System Control
      1. 6.6.1 OSC and PLL Block
        1. 6.6.1.1 External Reference Oscillator Clock Option
        2. 6.6.1.2 PLL-Based Clock Module
        3. 6.6.1.3 Loss of Input Clock
      2. 6.6.2 Watchdog Block
    7. 6.7 Low-Power Modes Block
  7. 7Applications, Implementation, and Layout
    1. 7.1 TI Design or Reference Design
  8. 8Device and Documentation Support
    1. 8.1 Getting Started
    2. 8.2 Device and Development Support Tool Nomenclature
    3. 8.3 Tools and Software
    4. 8.4 Documentation Support
    5. 8.5 Related Links
    6. 8.6 Community Resources
    7. 8.7 Trademarks
    8. 8.8 Electrostatic Discharge Caution
    9. 8.9 Glossary
  9. 9Mechanical, Packaging, and Orderable Information
    1. 9.1 Packaging Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • ZHH|179
  • ZJZ|176
  • ZAY|179
  • PGF|176
  • PTP|176
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Serial Peripheral Interface (SPI) Module (SPI-A)

The device includes the four-pin serial peripheral interface (SPI) module. One SPI module (SPI-A) is available. The SPI is a high-speed, synchronous serial I/O port that allows a serial bit stream of programmed length (1 to 16 bits) to be shifted into and out of the device at a programmable bit-transfer rate. Normally, the SPI is used for communications between the DSC controller and external peripherals or another processor. Typical applications include external I/O or peripheral expansion through devices such as shift registers, display drivers, and ADCs. Multidevice communications are supported by the master/slave operation of the SPI.

The SPI module features include:

  • Four external pins:
    • SPISOMI: SPI slave-output/master-input pin
    • SPISIMO: SPI slave-input/master-output pin
    • SPISTE: SPI slave transmit-enable pin
    • SPICLK: SPI serial-clock pin

NOTE

All four pins can be used as GPIO if the SPI module is not used.

  • Two operational modes: master and slave
  • Baud rate: 125 different programmable rates.

    TMS320F28335 TMS320F28334 TMS320F28333 TMS320F28332 TMS320F28235 TMS320F28234 TMS320F28232 q_spibrr_prs439.gif

    NOTE

    See Section 5 for maximum I/O pin toggling speed.

  • Data word length: 1 to 16 data bits
  • Four clocking schemes (controlled by clock polarity and clock phase bits) include:
    • Falling edge without phase delay: SPICLK active-high. SPI transmits data on the falling edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.
    • Falling edge with phase delay: SPICLK active-high. SPI transmits data one half-cycle ahead of the falling edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.
    • Rising edge without phase delay: SPICLK inactive-low. SPI transmits data on the rising edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.
    • Rising edge with phase delay: SPICLK inactive-low. SPI transmits data one half-cycle ahead of the rising edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.
  • Simultaneous receive and transmit operation (transmit function can be disabled in software)
  • Transmitter and receiver operations are accomplished through either interrupt-driven or polled algorithms.
  • Nine SPI module control registers: Located in control register frame beginning at address 7040h.
  • NOTE

    All registers in this module are 16-bit registers that are connected to Peripheral Frame 2. When a register is accessed, the register data is in the lower byte (7–0), and the upper byte (15–8) is read as zeros. Writing to the upper byte has no effect.

Enhanced features:

  • 16-level transmit/receive FIFO
  • Delayed transmit control

The SPI port operation is configured and controlled by the registers listed in Table 6-15.

Table 6-15 SPI-A Registers

NAME ADDRESS SIZE (x16) DESCRIPTION(1)
SPICCR 0x7040 1 SPI-A Configuration Control Register
SPICTL 0x7041 1 SPI-A Operation Control Register
SPISTS 0x7042 1 SPI-A Status Register
SPIBRR 0x7044 1 SPI-A Baud Rate Register
SPIRXEMU 0x7046 1 SPI-A Receive Emulation Buffer Register
SPIRXBUF 0x7047 1 SPI-A Serial Input Buffer Register
SPITXBUF 0x7048 1 SPI-A Serial Output Buffer Register
SPIDAT 0x7049 1 SPI-A Serial Data Register
SPIFFTX 0x704A 1 SPI-A FIFO Transmit Register
SPIFFRX 0x704B 1 SPI-A FIFO Receive Register
SPIFFCT 0x704C 1 SPI-A FIFO Control Register
SPIPRI 0x704F 1 SPI-A Priority Control Register
Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined results.

Figure 6-16 is a block diagram of the SPI in slave mode.

TMS320F28335 TMS320F28334 TMS320F28333 TMS320F28332 TMS320F28235 TMS320F28234 TMS320F28232 fbd_spi_prs439.gif
SPISTE is driven low by the master for a slave device.
Figure 6-16 SPI Module Block Diagram (Slave Mode)