SNVSBT6C July   2021  – December 2022 TPS38700-Q1

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Device State Diagram
      2. 8.3.2 Built-In Self Test and Configuration Load
      3. 8.3.3 CLK32K
      4. 8.3.4 BACKUP State
      5. 8.3.5 FAILSAFE State
      6. 8.3.6 Transitioning Sequences
        1. 8.3.6.1 Sequence 1: Power Up
        2. 8.3.6.2 Sequence 2: Emergency Power Down
        3. 8.3.6.3 Sequence 3: Sleep Entry
        4. 8.3.6.4 Sequence 4: Sleep Exit
        5. 8.3.6.5 Sequence 5 & 6: Power Down from Active and Sleep States
        6. 8.3.6.6 Sequence 7: Sleep Exit Due to NRST_IN
        7. 8.3.6.7 Sequence 8: RESET Due to NRST_IN
        8. 8.3.6.8 Sequence 9: Failsafe Power Down
        9. 8.3.6.9 Output Sequencing
      7. 8.3.7 I2C
    4. 8.4 Register Map Table
      1. 8.4.1 Register Descriptions
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Automotive Multichannel Sequencer and Monitor
      2. 9.2.2 Design Requirements
      3. 9.2.3 Detailed Design Procedure
      4. 9.2.4 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Power Supply Guidelines
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Nomenclature
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
      1.      Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.3.4 BACKUP State

In the BACKUP state only the battery is supplying power to the device, however the device must have gone through a VDD supplied state (and loaded configuration data) in order to enter this state. If no VDD supplied state has occurred, then the TPS38700-Q1 stays in the "OFF or Battery Installed" state, from which it will exit only with a valid VDD supply.

When in BACKUP state, the TPS38700-Q1 pins are in the following state:

  • ENx = Low (de-asserted)
  • CLK32K = Low (output disabled)
  • NRST = Low (asserted)
  • ACT and SLEEP inputs are ignored.

Crystal oscillator and RTC remain active with Acc_CLK32K accuracy, but the crystal oscillator fault monitor is not active. RTC_T[31:0], interrupt, and status registers are maintained and updated. Registers configuration is maintained as set before entering the BACKUP state. PROT1 and PROT2 registers are cleared. All remaining blocks are inactive.

Upon exiting from the BACKUP state, the last configuration is active and the device enters the SHDN1 state.