SLLSEZ6C February   2019  – October 2020 TUSB216

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Timing Requirements
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 High-speed Boost
      2. 7.3.2 RX Sensitivity
    4. 7.4 Device Functional Modes
      1. 7.4.1 Low-speed (LS) Mode
      2. 7.4.2 Full-speed (FS) Mode
      3. 7.4.3 High-speed (HS) Mode
      4. 7.4.4 High-speed Downstream Port Electrical Compliance Test Mode
      5. 7.4.5 Shutdown Mode
      6. 7.4.6 I2C Mode
      7. 7.4.7 BC 1.2 Battery Charging Controller
    5. 7.5 TUSB216 Registers
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Test Procedure to Construct USB High-speed Eye Diagram
          1. 8.2.2.1.1 For a Host Side Application
          2. 8.2.2.1.2 For a Device Side Application
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Electrical Characteristics

Over operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSMINTYP (1)MAXUNIT
POWER
IACTIVE_HSHigh Speed Active CurrentUSB channel = HS mode. 480 Mbps traffic. VCC supply stable, with Boost = Max2236mA
IIDLE_HSHigh Speed Idle CurrentUSB channel = HS mode, no traffic. VCC supply stable, Boost = Max2236mA
IHS_SUPSPENDHigh Speed Suspend CurrentUSB channel = HS Suspend mode. VCC supply stable0.751.4mA
IFSFull-Speed CurrentUSB channel = FS mode, 12 Mbps traffic, Vcc supply stable0.751.4mA
IDISCONNDisconnect PowerHost side application. No device attachment.0.801.4mA
ISHUTDNShutdown PowerRSTN driven low, VCC supply stable60115µA
CONTROL PIN LEAKAGE
ILKG_FSPin failsafe leakage current for SDA, RSTNVCC = 0 V, pin at VIH, max1015µA
ILKG_FSPin failsafe leakage current for RX_SENVCC = 0 V, pin at VIH, max615µA
ILKG_FSPin failsafe leakage current for SCLVCC = 0 V, pin at VIH, max70nA
INPUT RSTN
VIHHigh level input voltage1.53.6V
VILLow-level input voltage00.5V
IIHHigh level input currentVIH = 3.6 V, RPU enabled±15µA
IILLow level input currentVIL = 0V, RPU enabled±20µA
INPUT DIGITAL
VIHHigh level input voltage (CDP_ENZ)1.53.6V
VILLow-level input voltage (CDP_ENZ)00.5V
IILLow level input currentVIL = 0V±20µA
IIHHigh level input currentVIH = 3.6 V±15µA
INPUT RX_SEN (3-level input, for mid level leave pin floating)
VIH(Max)Maximum High level input voltage

RRXSEN1=37.5kΩ, RRXSEN2=12.5kΩ
 
VCC = 2.3V to 6.5V 5.5V
VIH(Min)Minimum High level input voltage

RRXSEN1=37.5kΩ, RRXSEN2=12.5kΩ
 
VCC = 2.3V to 6.5V
(% of VCC)
75%
VILLow level input voltage

22kΩ <= RRXSEN1 <= 40kΩ
 
0.75V
INPUT BOOST
RBOOST_LVL0External pulldown resistor for BOOST Level 0160Ω
RBOOST_LVL1External pulldown resistor for BOOST Level 11.51.82
RBOOST_LVL2External pulldown resistor for BOOST Level 23.43.63.96
RBOOST_LVL3External pulldown resistor  for BOOST Level 37.511
OUTPUTS CD, ENA_HS
VOHHigh level output voltage for CD and ENA_HSIO = –50 µA, VCC >= 3.0V2.5V
VOHHigh level output voltage  for CDIO = –25 µA, VCC = 2.3V1.7V
VOHHigh level output voltage  for ENA_HSIO = –25 µA, VCC = 2.3V1.8V
VOLLow level output voltage  for CD and ENA_HSIO = 50 µA0.3V
I2C
CI2C_BUSI2C Bus Capacitance4150pF
IOLI2C open drain output currentVOL = 0.4V1.5mA
VIL2.3V<= VCC<= 4.3V, VI2C_BUS = 1.8V +/-10%RPull-up =1.6kΩ to 2.5kΩ, % of VI2C_BUS25%
VILVI2C_BUS = 3.3V +/-10%RPull-up =2.8kΩ to 7kΩ, % of VI2C_BUS25%
VIH2.3V<= VCC<= 4.3V, VI2C_BUS = 1.8V +/-10%RPull-up =1.6kΩ to 2.5kΩ, % of VI2C_BUS80%
VIHVI2C_BUS = 3.3V +/-10%RPull-up =2.8kΩ to 7kΩ, % of VI2C_BUS75%
RPull-upVI2C_BUS = 1.8V +/-10%1.622.5kΩ
RPull-upVI2C_BUS = 3.3V +/-10%2.84.77kΩ
SCL Frequency100kHz
DxP, DxM
CIO_DXXCapacitance to GNDMeasured with VNA at 240 MHz, VCC supply stable, Redriver off2.5pF
All typical values are at VCC = 5 V, and TA = 25°C.