JAJSL70A February   2021  – January 2024 BQ25730

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 概要 (続き)
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics(BQ25730)
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Power-Up Sequence
      2. 8.3.2  Two-Level Battery Discharge Current Limit
      3. 8.3.3  Fast Role Swap Feature
      4. 8.3.4  CHRG_OK Indicator
      5. 8.3.5  Input and Charge Current Sensing
      6. 8.3.6  Input Voltage and Current Limit Setup
      7. 8.3.7  Battery Cell Configuration
      8. 8.3.8  Device HIZ State
      9. 8.3.9  USB On-The-Go (OTG)
      10. 8.3.10 Converter Operation
      11. 8.3.11 Inductance Detection Through IADPT Pin
      12. 8.3.12 Converter Compensation
      13. 8.3.13 Continuous Conduction Mode (CCM)
      14. 8.3.14 Pulse Frequency Modulation (PFM)
      15. 8.3.15 Switching Frequency and Dithering Feature
      16. 8.3.16 Current and Power Monitor
        1. 8.3.16.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 8.3.16.2 High-Accuracy Power Sense Amplifier (PSYS)
      17. 8.3.17 Input Source Dynamic Power Management
      18. 8.3.18 Input Current Optimizer (ICO)
      19. 8.3.19 Two-Level Adapter Current Limit (Peak Power Mode)
      20. 8.3.20 Processor Hot Indication
        1. 8.3.20.1 PROCHOT During Low Power Mode
        2. 8.3.20.2 PROCHOT Status
      21. 8.3.21 Device Protection
        1. 8.3.21.1 Watchdog Timer
        2. 8.3.21.2 Input Overvoltage Protection (ACOV)
        3. 8.3.21.3 Input Overcurrent Protection (ACOC)
        4. 8.3.21.4 System Overvoltage Protection (SYSOVP)
        5. 8.3.21.5 Battery Overvoltage Protection (BATOVP)
        6. 8.3.21.6 Battery Discharge Overcurrent Protection (BATOC)
        7. 8.3.21.7 Battery Short Protection (BATSP)
        8. 8.3.21.8 System Undervoltage Lockout (VSYS_UVP) and Hiccup Mode
        9. 8.3.21.9 Thermal Shutdown (TSHUT)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Forward Mode
        1. 8.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 8.4.1.2 Battery Charging
      2. 8.4.2 USB On-The-Go
      3. 8.4.3 Pass Through Mode (PTM)-Patented Technology
    5. 8.5 Programming
      1. 8.5.1 I2C Serial Interface
        1. 8.5.1.1 Timing Diagrams
        2. 8.5.1.2 Data Validity
        3. 8.5.1.3 START and STOP Conditions
        4. 8.5.1.4 Byte Format
        5. 8.5.1.5 Acknowledge (ACK) and Not Acknowledge (NACK)
        6. 8.5.1.6 Target Address and Data Direction Bit
        7. 8.5.1.7 Single Read and Write
        8. 8.5.1.8 Multi-Read and Multi-Write
        9. 8.5.1.9 Write 2-Byte I2C Commands
    6. 8.6 Register Map
      1. 8.6.1  ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
      2. 8.6.2  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 8.6.2.1 Battery Pre-Charge Current Clamp
      3. 8.6.3  ChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      4. 8.6.4  ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
      5. 8.6.5  ProchotStatus Register (I2C address = 23/22h) [reset = B800h]
      6. 8.6.6  IIN_DPM Register (I2C address = 25/24h) [reset = 4100h]
      7. 8.6.7  ADCVBUS/PSYS Register (I2C address = 27/26h)
      8. 8.6.8  ADCIBAT Register (I2C address = 29/28h)
      9. 8.6.9  ADCIIN/CMPIN Register (I2C address = 2B/2Ah)
      10. 8.6.10 ADCVSYS/VBAT Register (I2C address = 2D/2Ch)
      11. 8.6.11 ChargeOption1 Register (I2C address = 31/30h) [reset = 3F00h]
      12. 8.6.12 ChargeOption2 Register (I2C address = 33/32h) [reset = 00B7]
      13. 8.6.13 ChargeOption3 Register (I2C address = 35/34h) [reset = 0434h]
      14. 8.6.14 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A81h(2S~5s) 4A09(1S)]
      15. 8.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
      16. 8.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      17. 8.6.17 ChargeOption4 Register (I2C address = 3D/3Ch) [reset = 0048h]
      18. 8.6.18 Vmin Active Protection Register (I2C address = 3F/3Eh) [reset = 006Ch(2s~5s)/0004h(1S)]
      19. 8.6.19 OTGVoltage Register (I2C address = 07/06h) [reset = 09C4h]
      20. 8.6.20 OTGCurrent Register (I2C address = 09/08h) [reset = 3C00h]
      21. 8.6.21 InputVoltage(VINDPM) Register (I2C address = 0B/0Ah) [reset =VBUS-1.28V]
      22. 8.6.22 VSYS_MIN Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
      23. 8.6.23 IIN_HOST Register (I2C address = 0F/0Eh) [reset = 2000h]
      24. 8.6.24 ID Registers
        1. 8.6.24.1 ManufactureID Register (I2C address = 2Eh) [reset = 40h]
        2. 8.6.24.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = D5h]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Input Snubber and Filter for Voltage Spike Damping
        2. 9.2.2.2 ACP-ACN Input Filter
        3. 9.2.2.3 Inductor Selection
        4. 9.2.2.4 Input Capacitor
        5. 9.2.2.5 Output Capacitor
        6. 9.2.2.6 Power MOSFETs Selection
      3. 9.2.3 Application Curves
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
      1. 11.2.1 Layout Example Reference Top View
      2. 11.2.2 Inner Layer Layout and Routing Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 サード・パーティ製品に関する免責事項
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 ドキュメントの更新通知を受け取る方法
    4. 12.4 サポート・リソース
    5. 12.5 Trademarks
    6. 12.6 静電気放電に関する注意事項
    7. 12.7 用語集
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]

Figure 8-31 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
7 6 5 4 3 2 1 0
ADC_CONVADC_STARTADC_FULLSCALEReserved
R/WR/WR/WR/W R/W R/W R/W R/W
76543210
EN_ADC_CMPINEN_ADC_VBUSEN_ADC_PSYSEN_ADC_IINEN_ADC_IDCHGEN_ADC_ICHGEN_ADC_VSYSEN_ADC_VBAT
R/WR/WR/WR/WR/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

The ADC registers are read in the following order: VBAT, VSYS, ICHG, IDCHG, IIN, PSYS, VBUS, CMPIN. ADC is disabled in low power mode. Before enabling ADC, low power mode should be disabled first.

Table 8-38 ADCOption Register (I2C address = 3Bh) Field Descriptions
BITFIELDTYPERESETDESCRIPTION
7ADC_CONVR/W0bTypical each ADC channel conversion time is 25 ms maximum. Total ADC conversion time is the product of 25 ms and enabled channel counts.

0b: One-shot update. Do one set of conversion updates to registers REG0x29/28(), REG0x27/26(), REG0x2B/2A(), and REG0x2D/2C() after ADC_START = 1.

1b: Continuous update. Do a set of conversion updates to registers REG0x29/28(), REG0x27/26(), REG0x2B/2A(), and REG0x2D/2C()every 1 sec.

6ADC_STARTR/W0b

0b: No ADC conversion

1b: Start ADC conversion. After the one-shot update is complete, this bit automatically resets to zero

5ADC_FULLSCALER/W1b

ADC input voltage range adjustment for PSYS and CMPIN ADC Channels. 2.04-V full scale holds 8 mV/LSB resolution and 3.06-V full scale holds 12 mV/LSB resolution

0b: 2.04 V

1b: 3.06 V <default at POR>(Not accurate for REGN<6-V application (VBUS & VSYS< 6V))

4-0ReservedR/W00000bReserved
Table 8-39 ADCOption Register (I2C address = 3Ah) Field Descriptions
BITFIELDTYPERESETDESCRIPTION
7EN_ADC_CMPINR/W0b

0b: Disable <default at POR>

1b: Enable

6EN_ADC_VBUSR/W0b

0b: Disable <default at POR>

1b: Enable

5EN_ADC_PSYSR/W0b

0b: Disable <default at POR>

1b: Enable

4EN_ADC_IINR/W0b

0b: Disable <default at POR>

1b: Enable

3EN_ADC_IDCHGR/W0b

0b: Disable <default at POR>

1b: Enable

2EN_ADC_ICHGR/W0b

0b: Disable <default at POR>

1b: Enable

1EN_ADC_VSYSR/W0b

0b: Disable <default at POR>

1b: Enable

0EN_ADC_VBATR/W0b

0b: Disable <default at POR>

1b: Enable