4 改訂履歴
Changes from F Revision (May 2015) to G Revision
- Changed Figure 19 の DMD マーキング画像オブジェクトGo
Changes from E Revision (September 2013) to F Revision
- Added 「ESD 定格」、「機能説明」セクション、「デバイスの機能モード」セクション、「アプリケーションと実装」セクション、「電源に関する推奨事項」セクション、「レイアウト」セクション、「デバイスおよびドキュメントのサポート」セクション、「メカニカル、パッケージ、および注文情報」セクションGo
- Changed Incorrect VCC2 value from 9V to 8VGo
- Changed LVDS ƒclock to200 MHz - previously incorrectly listed as 150 MHzGo
- Added Max Recommended DMD Temperature – Derating CurveGo
- Added LVCMOS Output Measurement Condition FigureGo
- Changed Incorrect tC value from 4 ns to 5 ns (200 MHz clock)Go
- Changed Incorrect tW value from 1.25 ns to 2.5 ns (200 MHz clock)Go
- Changed SCP Bus DiagramsGo
- Added LVDS Voltage Definition FigureGo
- Changed LVDS Waveform Requirements FigureGo
- Added LVDS Equivalent Input Circuit FigureGo
- Added LVDS & SCP Rise and Fall Time FiguresGo
- Moved the Mechanical section from Recommended Operating Conditions table to the System Mounting Interface Loads section Go
- Added Micromirror Array Physical Characteristics section Go
- Changed Micromirror Array Physical Characteristics Figure to generic image (M x N)Go
- Added Micromirror Array Optical Characteristics section Go
- Changed specular reflectivity wavelength range to 420 - 700 nm (from 400 - 700 nm) to match Recommended Operating ConditionsGo
- Changed Micromirror Landed Orientation and Tilt Figure to generic image (M x N)Go
- Added Window Characteristics section Go
- Added Chipset Component Usage Specification section Go
- Changed Micromirror Array, Pitch, Hinge Axis Orientation Figure to generic image (M x N)Go
- Changed Micromirror States: On, Off, Flat Figure to generic DMD imageGo
- Changed Test Point locations from TC1 & TC2 to TP1 - TP5Go
- Changed Test Point location Diagram to show TP1 - TP5Go
- Added Micromirror Landed-on/Landed-Off Duty Cycle sectionGo
- Changed Typical Application diagramGo
- Replaced "DAD" with "DLPA200"Go
Changes from D Revision (October 2012) to E Revision
Changes from C Revision (June 2012) to D Revision
- 製品型番の表記規則を「DLP5500FYA」から「DLP5500AFYA」に変更Go
- メカニカル ICD を V2 に更新し、ウィンドウの高さを多少変更Go
Changes from B Revision (Spetember 2011) to C Revision
- 「特長」一覧にパッケージのフットプリントとソケットの情報を追加Go
- Deleted 「概要」から冗長な情報をGo
- Changed the Illumination power density Max value of <420 mm From: 20 To: 2 mW/cm2Go
- Changed Storage temperature range and humidity values in Absolute Maximum Ratings Go
- Added Operating Case Temperature, Operating Humidity, Operating Device Temperature Gradient and Operating Landed Duty-Cycle to RECOMMENDED OPERATING CONDITIONS.Go
- Added Mirror metal specular reflectivity and Illumination overfill values to "Micromirror Array Optical Characteristics" tableGo
- Corrected the CL2W, Qarray and Tarray values in Micromirror Array Temperature Calculation for Uniform Illumination.Go
- 「関連資料」セクションのドキュメントの参照を訂正Go
Changes from A Revision (June 2010) to B Revision
- Changed the window refractive index NOM spec From: 1.5090 To: 1.5119Go
- Added table note "At a wavelength of 632.8 nm"Go
Changes from * Revision (April 2010) to A Revision
- Changed VREF to VCC1Go
- Added |VID| to the absolute max tableGo
- Added VMBRST to the absolute max tableGo
- Clarified Note6 measurement point Go
- Changed the Illumination power density Max value of <420 mm From: 2 To: 20 mW/cm2Go
- Added 関連資料Go