SLLSEL7A October   2014  – November 2015 DRV8848

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 PWM Motor Drivers
      2. 7.3.2 Bridge Control
      3. 7.3.3 Parallel Operation
      4. 7.3.4 Current Regulation
      5. 7.3.5 Current Recirculation and Decay Modes
      6. 7.3.6 Protection Circuits
        1. 7.3.6.1 OCP
        2. 7.3.6.2 TSD
        3. 7.3.6.3 UVLO
    4. 7.4 Device Functional Modes
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Current Regulation
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
    1. 9.1 Bulk Capacitance Sizing
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Community Resources
    2. 11.2 Trademarks
    3. 11.3 Electrostatic Discharge Caution
    4. 11.4 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

5 Pin Configuration and Functions

PWP Package
16-Pin HTSSOP
Top View
DRV8848 po_LLSEL7.gif

Pin Functions

PIN TYPE DESCRIPTION
NAME NO.
AIN1 16 I Bridge A input 1 Controls AOUT1; tri-level input
AIN2 15 I Bridge A input 2 Controls AOUT2; tri-level input
AISEN 3 O Winding A sense Connect to current sense resistor for bridge A, or GND if current regulation is not required
AOUT1 2 O Winding A output
AOUT2 4
BIN1 9 I Bridge B input 1 Controls BOUT1; internal pulldown
BIN2 10 I Bridge B input 2 Controls BOUT2; internal pulldown
BISEN 6 O Winding B sense Connect to current sense resistor for bridge A, or GND if current regulation is not required
BOUT1 7 O Winding B output
BOUT2 5
GND 13 PWR Device ground Both the GND pin and device PowerPAD must be connected to ground
PPAD
nFAULT 8 OD Fault indication pin Pulled logic low with fault condition; open-drain output requires external pullup
nSLEEP 1 I Sleep mode input Logic high to enable device; logic low to enter low-power sleep mode; internal pulldown
VINT 14 — Internal regulator Internal supply voltage; bypass to GND with 2.2-μF, 6.3-V capacitor
VM 12 PWR Power supply Connect to motor power supply; bypass to GND with a 0.1- and 10-μF (minimum) ceramic capacitor rated for VM
VREF 11 I Full-scale current reference input Voltage on this pin sets the full scale chopping current; short to VINT if not supplying an external reference voltage

External Components

COMPONENT PIN 1 PIN 2 RECOMMENDED
CVM VM GND 10-µF (minimum) ceramic capacitor rated for VM
CVM VM GND 0.1-µF ceramic capacitor rated for VM
CVINT VINT GND 6.3-V, 2.2-µF ceramic capacitor
RnFAULT VCC(1) nFAULT >1 kΩ
RAISEN AISEN GND Sense resistor, see Typical Application for sizing
RBISEN BISEN GND Sense resistor, see Typical Application for sizing
(1) VCC is not a pin on the DRV8848, but a VCC supply voltage pullup is required for open-drain output nFAULT; nFAULT may be pulled up to VINT