JAJSGI2G September   2015  – November 2018

PRODUCTION DATA.

1. 特長
2. アプリケーション
3. 概要
1.     Device Images
4. 改訂履歴
5. Pin Configuration and Functions
6. Specifications
7. Parameter Measurement Information
8. Detailed Description
1. 8.1 Overview
2. 8.2 Functional Block Diagram
3. 8.3 Feature Description
4. 8.4 Device Functional Modes
9. Application and Implementation
1. 9.1 Application Information
2. 9.2 Typical Application
1. 9.2.1 Design Requirements
2. 9.2.2 Detailed Design Procedure
3. 9.2.3 Application Curves
4. 9.2.4 System Examples
10. 10Power Supply Recommendations
11. 11Layout
12. 12デバイスおよびドキュメントのサポート
1. 12.1 デバイス・サポート
2. 12.2 ドキュメントのサポート
3. 12.3 関連リンク
4. 12.4 ドキュメントの更新通知を受け取る方法
5. 12.5 コミュニティ・リソース
6. 12.6 商標
7. 12.7 静電気放電に関する注意事項
8. 12.8 Glossary
13. 13メカニカル、パッケージ、および注文情報

• DBV|6

#### 9.2.2.5.2 Turns Ratio Estimate

Assume the rectifier diodes and linear regulator has been selected. Also, it has been determined that the transformer chosen must have a V-t product of at least 11 Vμs. However, before searching the manufacturer web sites for a suitable transformer, the user still needs to know its minimum turns ratio that allows the push-pull converter to operate flawlessly over the specified current and temperature range. This minimum transformation ratio is expressed through the ratio of minimum secondary to minimum primary voltage multiplied by a correction factor that takes the transformer’s typical efficiency of 97% into account:

Equation 5. VP-min = VIN-min - VDS-max

VS-min must be large enough to allow for a maximum voltage drop, VF-max, across the rectifier diode and still provide sufficient input voltage for the regulator to remain in regulation. From the LDO Selection section, this minimum input voltage is known and by adding VF-max gives the minimum secondary voltage with:

Equation 6. VS-min = VF-max + VDO-max + VO-max Figure 45. Establishing the Required Minimum Turns Ratio Through Nmin = 1.031 × VS-min / VP-min

Then calculating the available minimum primary voltage, VP-min, involves subtracting the maximum possible drain-source voltage of the device, VDS-max, from the minimum converter input voltage VIN-min:

Equation 7. VP-min = VIN-min – VDS-max

VDS-max however, is the product of the maximum RDS(on) and ID values for a given supply specified in the data sheet:

Equation 8. VDS-max = RDS-max × IDmax

Then inserting Equation 8 into Equation 7 yields:

Equation 9. VP-min = VIN-min - RDS-max x IDmax

and inserting Equation 9 and Equation 6 into Equation 5 provides the minimum turns ration with:

Equation 10. Example:

For a 3.3 VIN to 5 VOUT converter using the rectifier diode MBR0520L and the 5 V LDO, the data sheet values taken for a load current of 600 mA and a maximum temperature of 85°C are VF-max = 0.2 V,
VDO-max = 0.5 V, and VO-max = 5.1 V.

Then assuming that the converter input voltage is taken from a 3.3 V controller supply with a maximum ±2% accuracy makes VIN-min = 3.234 V. Finally the maximum values for drain-source resistance and drain current at 3.3 V are taken from the data sheet with RDS-max = 0.31 Ω and ID-max = 1 A.

Inserting the values above into Equation 10 yields a minimum turns ratio of:

Equation 11. Most commercially available transformers for 3-to-5 V push-pull converters offer turns ratios between 2.0 and 2.3 with a common tolerance of ±3%.