SPRUJD3A July   2025  – October 2025 F28E120SB , F28E120SC

 

  1.   1
  2.   Read This First
    1.     About This Manual
    2.     Notational Conventions
    3.     Glossary
    4.     Related Documentation From Texas Instruments
    5.     Support Resources
    6.     Trademarks
  3. 1 C2000™ Microcontrollers Software Support
    1. 1.1 Introduction
    2. 1.2 C2000Ware Structure
    3. 1.3 Documentation
    4. 1.4 Devices
    5. 1.5 Libraries
    6. 1.6 Code Composer Studio™ Integrated Development Environment (IDE)
    7. 1.7 SysConfig and PinMUX Tool
  4. 2 C28x Processor
    1. 2.1 Introduction
    2. 2.2 C28X Related Collateral
    3. 2.3 Features
    4. 2.4 Floating-Point Unit (FPU)
  5. 3 System Control and Interrupts
    1. 3.1  Introduction
      1. 3.1.1 SYSCTL Related Collateral
      2. 3.1.2 LOCK Protection on System Configuration Registers
      3. 3.1.3 EALLOW Protection
    2. 3.2  Power Management
    3. 3.3  Device Identification and Configuration Registers
    4. 3.4  Resets
      1. 3.4.1  Reset Sources
      2. 3.4.2  External Reset (XRS)
      3. 3.4.3  Power-On Reset (POR)
      4. 3.4.4  Brown-Out-Reset (BOR)
      5. 3.4.5  Watchdog Reset (WDRS)
      6. 3.4.6  NMI Watchdog Reset (NMIWDRS)
      7. 3.4.7  Debugger Reset (SYSRS)
      8. 3.4.8  DCSM Safe Code Copy Reset (SCCRESET)
      9. 3.4.9  Simulate External Reset (SIMRESET.XRS)
      10. 3.4.10 Simulate CPU Reset (SIMRESET_CPU1RS)
    5. 3.5  Peripheral Interrupts
      1. 3.5.1 Interrupt Concepts
      2. 3.5.2 Interrupt Architecture
        1. 3.5.2.1 Peripheral Stage
        2. 3.5.2.2 PIE Stage
        3. 3.5.2.3 CPU Stage
      3. 3.5.3 Interrupt Entry Sequence
      4. 3.5.4 Configuring and Using Interrupts
        1. 3.5.4.1 Enabling Interrupts
        2. 3.5.4.2 Handling Interrupts
        3. 3.5.4.3 Disabling Interrupts
        4. 3.5.4.4 Nesting Interrupts
        5. 3.5.4.5 Vector Address Validity Check
      5. 3.5.5 PIE Channel Mapping
      6. 3.5.6 PIE Interrupt Priority
        1. 3.5.6.1 Channel Priority
        2. 3.5.6.2 Group Priority
      7. 3.5.7 System Error
      8. 3.5.8 Vector Tables
    6. 3.6  Exceptions and Non-Maskable Interrupts
      1. 3.6.1 Configuring and Using NMIs
      2. 3.6.2 Emulation Considerations
      3. 3.6.3 NMI Sources
        1. 3.6.3.1 Missing Clock Detection Logic
        2. 3.6.3.2 Flash Uncorrectable ECC Error
        3. 3.6.3.3 Software-Forced Error
      4. 3.6.4 Illegal Instruction Trap (ITRAP)
      5. 3.6.5 ERRORSTS Pin
    7. 3.7  Clocking
      1. 3.7.1  Clock Sources
        1. 3.7.1.1 Primary Internal Oscillator (SYSOSC)
        2. 3.7.1.2 Backup Wide-Range Oscillator (WROSC)
        3. 3.7.1.3 External Oscillator (XTAL)
      2. 3.7.2  Derived Clocks
        1. 3.7.2.1 Oscillator Clock (OSCCLK)
        2. 3.7.2.2 System PLL Output Clock (PLLRAWCLK)
      3. 3.7.3  Device Clock Domains
        1. 3.7.3.1 System Clock (PLLSYSCLK)
        2. 3.7.3.2 CPU Clock (CPUCLK)
        3. 3.7.3.3 CPU Subsystem Clock (SYSCLK)
        4. 3.7.3.4 Low-Speed Peripheral Clock (LSPCLK and PERx.LSPCLK)
        5. 3.7.3.5 CPU Timer2 Clock (TIMER2CLK)
      4. 3.7.4  XCLKOUT
      5. 3.7.5  Clock Connectivity
      6. 3.7.6  Clock Source and PLL Setup
      7. 3.7.7  Using an External Crystal or Resonator
      8. 3.7.8  Using an External Oscillator
      9. 3.7.9  Choosing PLL Settings
      10. 3.7.10 System Clock Setup
      11. 3.7.11 SYS PLL Bypass
      12. 3.7.12 Clock (OSCCLK) Failure Detection
        1. 3.7.12.1 Missing Clock Detection
    8. 3.8  32-Bit CPU Timers 0/1/2
    9. 3.9  Watchdog Timer
      1. 3.9.1 Servicing the Watchdog Timer
      2. 3.9.2 Minimum Window Check
      3. 3.9.3 Watchdog Reset or Watchdog Interrupt Mode
      4. 3.9.4 Watchdog Operation in Low Power-Modes
      5. 3.9.5 Emulation Considerations
    10. 3.10 Low-Power Modes
      1. 3.10.1 Clock-Gating Low-Power Modes
      2. 3.10.2 IDLE
      3. 3.10.3 STANDBY
      4. 3.10.4 HALT
    11. 3.11 Memory Controller Module
      1. 3.11.1 Dedicated RAM (Mx RAM)
      2. 3.11.2 Global Shared RAM (GSx RAM)
      3. 3.11.3 Access Arbitration
      4. 3.11.4 Memory Error Detection, Correction, and Error Handling
        1. 3.11.4.1 Error Detection and Correction
        2. 3.11.4.2 Error Handling
      5. 3.11.5 Application Test Hooks for Error Detection and Correction
      6. 3.11.6 RAM Initialization
    12. 3.12 JTAG
      1. 3.12.1 JTAG Noise and TAP_STATUS
    13. 3.13 System Control Register Configuration Restrictions
    14. 3.14 Software
      1. 3.14.1 SYSCTL Examples
        1. 3.14.1.1 Missing clock detection (MCD)
        2. 3.14.1.2 XCLKOUT (External Clock Output) Configuration
    15. 3.15 SYSCTRL Registers
      1. 3.15.1  SYSCTRL Base Address Table
      2. 3.15.2  CPUTIMER_REGS Registers
      3. 3.15.3  PIE_CTRL_REGS Registers
      4. 3.15.4  WD_REGS Registers
      5. 3.15.5  NMI_INTRUPT_REGS Registers
      6. 3.15.6  XINT_REGS Registers
      7. 3.15.7  SYNC_SOC_REGS Registers
      8. 3.15.8  DMA_CLA_SRC_SEL_REGS Registers
      9. 3.15.9  DEV_CFG_REGS Registers
      10. 3.15.10 CLK_CFG_REGS Registers
      11. 3.15.11 CPU_SYS_REGS Registers
      12. 3.15.12 SYS_STATUS_REGS Registers
      13. 3.15.13 MEM_CFG_REGS Registers
      14. 3.15.14 MEMORY_ERROR_REGS Registers
      15. 3.15.15 ROM_WAIT_STATE_REGS Registers
      16. 3.15.16 TEST_ERROR_REGS Registers
      17. 3.15.17 UID_REGS Registers
  6. 4 ROM Code and Peripheral Booting
    1. 4.1 Introduction
      1. 4.1.1 ROM Related Collateral
    2. 4.2 Device Boot Sequence
    3. 4.3 Device Boot Modes
      1. 4.3.1 Default Boot Modes
      2. 4.3.2 Custom Boot Modes
    4. 4.4 Device Boot Configurations
      1. 4.4.1 Configuring Boot Mode Pins
      2. 4.4.2 Configuring Boot Mode Table Options
      3. 4.4.3 Boot Mode Example Use Cases
        1. 4.4.3.1 Zero Boot Mode Select Pins
        2. 4.4.3.2 One Boot Mode Select Pin
        3. 4.4.3.3 Three Boot Mode Select Pins
    5. 4.5 Device Boot Flow Diagrams
      1. 4.5.1 Boot Flow
      2. 4.5.2 Emulation Boot Flow
      3. 4.5.3 Standalone Boot Flow
    6. 4.6 Device Reset and Exception Handling
      1. 4.6.1 Reset Causes and Handling
      2. 4.6.2 Exceptions and Interrupts Handling
    7. 4.7 Boot ROM Description
      1. 4.7.1  Boot ROM Configuration Registers
        1. 4.7.1.1 GPREG2 Usage and Configuration
      2. 4.7.2  Entry Points
      3. 4.7.3  Wait Points
      4. 4.7.4  Secure Flash Boot
        1. 4.7.4.1 Secure Flash CPU1 Linker File Example
      5. 4.7.5  Memory Maps
        1. 4.7.5.1 Boot ROM Memory Maps
        2. 4.7.5.2 Reserved RAM Memory Maps
      6. 4.7.6  ROM Tables
      7. 4.7.7  Boot Modes and Loaders
        1. 4.7.7.1 Boot Modes
          1. 4.7.7.1.1 Flash Boot
          2. 4.7.7.1.2 RAM Boot
          3. 4.7.7.1.3 Wait Boot
        2. 4.7.7.2 Bootloaders
          1. 4.7.7.2.1 SCI Boot Mode
          2. 4.7.7.2.2 SPI Boot Mode
          3. 4.7.7.2.3 I2C Boot Mode
          4. 4.7.7.2.4 Parallel Boot Mode
      8. 4.7.8  GPIO Assignments
      9. 4.7.9  Secure ROM Function APIs
      10. 4.7.10 Clock Initializations
      11. 4.7.11 Boot Status Information
        1. 4.7.11.1 Booting Status
      12. 4.7.12 ROM Version
    8. 4.8 Application Notes for Using the Bootloaders
      1. 4.8.1 Bootloader Data Stream Structure
        1. 4.8.1.1 Data Stream Structure 8-bit
      2. 4.8.2 The C2000 Hex Utility
        1. 4.8.2.1 HEX2000.exe Command Syntax
    9. 4.9 Software
      1. 4.9.1 BOOT Examples
  7. 5 Dual Code Security Module (DCSM)
    1. 5.1 Introduction
      1. 5.1.1 DCSM Related Collateral
    2. 5.2 Functional Description
      1. 5.2.1 CSM Passwords
      2. 5.2.2 Emulation Code Security Logic (ECSL)
      3. 5.2.3 CPU Secure Logic
      4. 5.2.4 Execute-Only Protection
      5. 5.2.5 Password Lock
      6. 5.2.6 JTAGLOCK
      7. 5.2.7 Link Pointer and Zone Select
      8. 5.2.8 C Code Example to Get Zone Select Block Addr for Zone1
    3. 5.3 Flash and OTP Erase/Program
    4. 5.4 Secure Copy Code
    5. 5.5 SecureCRC
    6. 5.6 CSM Impact on Other On-Chip Resources
      1. 5.6.1 RAMOPEN
    7. 5.7 Incorporating Code Security in User Applications
      1. 5.7.1 Environments That Require Security Unlocking
      2. 5.7.2 CSM Password Match Flow
      3. 5.7.3 C Code Example to Unsecure C28x Zone1
      4. 5.7.4 C Code Example to Resecure C28x Zone1
      5. 5.7.5 Environments That Require ECSL Unlocking
      6. 5.7.6 ECSL Password Match Flow
      7. 5.7.7 ECSL Disable Considerations for any Zone
        1. 5.7.7.1 C Code Example to Disable ECSL for C28x Zone1
      8. 5.7.8 Device Unique ID
    8. 5.8 Software
      1. 5.8.1 DCSM Examples
        1. 5.8.1.1 Empty DCSM Tool Example
    9. 5.9 DCSM Registers
      1. 5.9.1 DCSM Base Address Table
      2. 5.9.2 DCSM_Z1_REGS Registers
      3. 5.9.3 DCSM_Z2_REGS Registers
      4. 5.9.4 DCSM_COMMON_REGS Registers
      5. 5.9.5 DCSM_Z1_OTP Registers
      6. 5.9.6 DCSM_Z2_OTP Registers
  8. 6 Flash Module
    1. 6.1  Introduction to Flash and OTP Memory
      1. 6.1.1 FLASH Related Collateral
      2. 6.1.2 Features
      3. 6.1.3 Flash Tools
      4. 6.1.4 Default Flash Configuration
    2. 6.2  Flash Bank, OTP, and Pump
    3. 6.3  Flash Wrapper
    4. 6.4  Flash and OTP Memory Performance
    5. 6.5  Flash Read Interface
      1. 6.5.1 C28x-Flash Read Interface
        1. 6.5.1.1 Standard Read Mode
        2. 6.5.1.2 Prefetch Mode
        3. 6.5.1.3 Data Cache
        4. 6.5.1.4 Flash Read Operation
    6. 6.6  Flash Erase and Program
      1. 6.6.1 Erase
      2. 6.6.2 Program
      3. 6.6.3 Verify
    7. 6.7  Error Correction Code (ECC) Protection
      1. 6.7.1 Single-Bit Data Error
      2. 6.7.2 Uncorrectable Error
      3. 6.7.3 ECC Logic Self Test
    8. 6.8  Reserved Locations Within Flash and OTP
    9. 6.9  Migrating an Application from RAM to Flash
    10. 6.10 Procedure to Change the Flash Control Registers
    11. 6.11 Software
      1. 6.11.1 FLASH Examples
        1. 6.11.1.1 Flash Programming with AutoECC, DataAndECC, DataOnly and EccOnly
    12. 6.12 FLASH Registers
      1. 6.12.1 FLASH Base Address Table
      2. 6.12.2 FLASH_CTRL_REGS Registers
      3. 6.12.3 FLASH_ECC_REGS Registers
  9. 7 Dual-Clock Comparator (DCC)
    1. 7.1 Introduction
      1. 7.1.1 Features
      2. 7.1.2 Block Diagram
    2. 7.2 Module Operation
      1. 7.2.1 Configuring DCC Counters
      2. 7.2.2 Single-Shot Measurement Mode
      3. 7.2.3 Continuous Monitoring Mode
      4. 7.2.4 Error Conditions
    3. 7.3 Interrupts
    4. 7.4 Software
      1. 7.4.1 DCC Examples
        1. 7.4.1.1 DCC Single shot Clock verification
        2. 7.4.1.2 DCC Single shot Clock measurement
        3. 7.4.1.3 DCC Continuous clock monitoring
        4. 7.4.1.4 DCC Continuous clock monitoring
        5. 7.4.1.5 DCC Detection of clock failure
    5. 7.5 DCC Registers
      1. 7.5.1 DCC Base Address Table
      2. 7.5.2 DCC_REGS Registers
  10. 8 General-Purpose Input/Output (GPIO)
    1. 8.1  Introduction
      1. 8.1.1 GPIO Related Collateral
    2. 8.2  Configuration Overview
    3. 8.3  Digital Inputs on ADC Pins (AIOs)
    4. 8.4  Digital Inputs and Outputs on ADC Pins (AGPIOs)
    5. 8.5  Digital General-Purpose I/O Control
    6. 8.6  Input Qualification
      1. 8.6.1 No Synchronization (Asynchronous Input)
      2. 8.6.2 Synchronization to SYSCLKOUT Only
      3. 8.6.3 Qualification Using a Sampling Window
    7. 8.7  GPIO and Peripheral Muxing
      1. 8.7.1 GPIO Muxing
      2. 8.7.2 Peripheral Muxing
    8. 8.8  Internal Pullup Configuration Requirements
    9. 8.9  Open-Drain Configuration Requirements
    10. 8.10 Software
      1. 8.10.1 GPIO Examples
        1. 8.10.1.1 Device GPIO Setup
        2. 8.10.1.2 Device GPIO Toggle
        3. 8.10.1.3 Device GPIO Interrupt
        4. 8.10.1.4 External Interrupt (XINT)
      2. 8.10.2 LED Examples
    11. 8.11 GPIO Registers
      1. 8.11.1 GPIO Base Address Table
      2. 8.11.2 GPIO_CTRL_REGS Registers
      3. 8.11.3 GPIO_DATA_REGS Registers
      4. 8.11.4 GPIO_DATA_READ_REGS Registers
  11. 9 Crossbar (X-BAR)
    1. 9.1 Input X-BAR
    2. 9.2 MCPWM and GPIO Output X-BAR
      1. 9.2.1 MCPWM X-BAR
        1. 9.2.1.1 MCPWM X-BAR Architecture
      2. 9.2.2 GPIO Output X-BAR
        1. 9.2.2.1 GPIO Output X-BAR Architecture
      3. 9.2.3 X-BAR Flags
    3. 9.3 XBAR Registers
      1. 9.3.1 XBAR Base Address Table
      2. 9.3.2 INPUT_XBAR_REGS Registers
      3. 9.3.3 XBAR_REGS Registers
      4. 9.3.4 PWM_XBAR_REGS Registers
      5. 9.3.5 OUTPUT_XBAR_REGS Registers
  12. 10Direct Memory Access (DMA)
    1. 10.1 Introduction
      1. 10.1.1 Features
      2. 10.1.2 Block Diagram
    2. 10.2 Architecture
      1. 10.2.1 Peripheral Interrupt Event Trigger Sources
      2. 10.2.2 DMA Bus
    3. 10.3 Address Pointer and Transfer Control
    4. 10.4 Pipeline Timing and Throughput
    5. 10.5 Channel Priority
      1. 10.5.1 Round-Robin Mode
      2. 10.5.2 Channel 1 High-Priority Mode
    6. 10.6 Overrun Detection Feature
    7. 10.7 Software
      1. 10.7.1 DMA Examples
        1. 10.7.1.1 DMA GSRAM Transfer (dma_ex1_gsram_transfer)
        2. 10.7.1.2 DMA GSRAM Transfer (dma_ex2_gsram_transfer)
    8. 10.8 DMA Registers
      1. 10.8.1 DMA Base Address Table
      2. 10.8.2 DMA_REGS Registers
      3. 10.8.3 DMA_CH_REGS Registers
  13. 11Analog Subsystem
    1. 11.1 Introduction
      1. 11.1.1 Features
      2. 11.1.2 Block Diagram
    2. 11.2 Digital Inputs on ADC Pins (AIOs)
    3. 11.3 Digital Inputs and Outputs on ADC Pins (AGPIOs)
    4. 11.4 Analog Pins and Internal Connections
    5. 11.5 ASBSYS Registers
      1. 11.5.1 ASBSYS Base Address Table
      2. 11.5.2 ANALOG_SUBSYS_REGS Registers
  14. 12Analog-to-Digital Converter (ADC)
    1. 12.1  Introduction
      1. 12.1.1 Features
      2. 12.1.2 ADC Related Collateral
      3. 12.1.3 Block Diagram
    2. 12.2  ADC Configurability
      1. 12.2.1 ADC Clock Configuration
      2. 12.2.2 Resolution
      3. 12.2.3 Voltage Reference
        1. 12.2.3.1 External Reference Mode
        2. 12.2.3.2 Internal Reference Mode
        3. 12.2.3.3 Selecting Reference Mode
      4. 12.2.4 Signal Mode
        1. 12.2.4.1 Expected Conversion Results
        2. 12.2.4.2 Interpreting Conversion Results
    3. 12.3  SOC Principle of Operation
      1. 12.3.1 SOC Configuration
      2. 12.3.2 Trigger Operation
        1. 12.3.2.1 Trigger Repeaters
          1. 12.3.2.1.1 Oversampling Mode
          2. 12.3.2.1.2 Re-trigger Spread
          3. 12.3.2.1.3 Trigger Repeater Configuration
            1. 12.3.2.1.3.1 Register Shadow Updates
          4. 12.3.2.1.4 Re-Trigger Logic
          5. 12.3.2.1.5 Multi-Path Triggering Behavior
      3. 12.3.3 ADC Acquisition (Sample and Hold) Window
      4. 12.3.4 Sample Capacitor Reset
      5. 12.3.5 ADC Input Models
      6. 12.3.6 Channel Selection
    4. 12.4  SOC Configuration Examples
      1. 12.4.1 Single Conversion from MCPWM Trigger
      2. 12.4.2 Multiple Conversions from CPU Timer Trigger
      3. 12.4.3 Software Triggering of SOCs
    5. 12.5  ADC Conversion Priority
    6. 12.6  EOC and Interrupt Operation
      1. 12.6.1 Interrupt Overflow
      2. 12.6.2 Continue to Interrupt Mode
      3. 12.6.3 Early Interrupt Configuration Mode
    7. 12.7  Post-Processing Blocks
      1. 12.7.1 PPB Offset Correction
      2. 12.7.2 PPB Error Calculation
      3. 12.7.3 PPB Limit Detection and Zero-Crossing Detection
    8. 12.8  Opens/Shorts Detection Circuit (OSDETECT)
      1. 12.8.1 Open Short Detection Implementation
      2. 12.8.2 Detecting an Open Input Pin
      3. 12.8.3 Detecting a Shorted Input Pin
    9. 12.9  Power-Up Sequence
    10. 12.10 ADC Calibration
      1. 12.10.1 ADC Zero Offset Calibration
    11. 12.11 ADC Timings
      1. 12.11.1 ADC Timing Diagrams
      2. 12.11.2 Post-Processing Block Timings
    12. 12.12 Additional Information
      1. 12.12.1 Choosing an Acquisition Window Duration
      2. 12.12.2 Result Register Mapping
      3. 12.12.3 Internal Temperature Sensor
      4. 12.12.4 Designing an External Reference Circuit
      5. 12.12.5 ADC-DAC Loopback Testing
      6. 12.12.6 Internal Test Mode
    13. 12.13 Software
      1. 12.13.1 ADC Examples
        1. 12.13.1.1 ADC Software Triggering
        2. 12.13.1.2 ADC MCPWM Triggering
        3. 12.13.1.3 ADC Temperature Sensor Conversion
        4. 12.13.1.4 ADC Continuous Conversions Read by DMA (adc_soc_continuous_dma)
        5. 12.13.1.5 ADC PPB Offset (adc_ppb_offset)
        6. 12.13.1.6 ADC PPB Limits (adc_ppb_limits)
        7. 12.13.1.7 ADC SOC Oversampling
        8. 12.13.1.8 ADC Trigger Repeater Oversampling
    14. 12.14 ADC Registers
      1. 12.14.1 ADC Base Address Table
      2. 12.14.2 ADC_LITE_RESULT_REGS Registers
      3. 12.14.3 ADC_LITE_REGS Registers
  15. 13Comparator Subsystem (CMPSS)
    1. 13.1 Introduction
      1. 13.1.1 Features
      2. 13.1.2 CMPSS Related Collateral
      3. 13.1.3 Block Diagram
    2. 13.2 Comparator
    3. 13.3 Reference DAC
    4. 13.4 Digital Filter
      1. 13.4.1 Filter Initialization Sequence
    5. 13.5 Using the CMPSS
      1. 13.5.1 LATCHCLR, and MCPWMSYNCPER Signals
      2. 13.5.2 Synchronizer, Digital Filter, and Latch Delays
      3. 13.5.3 Calibrating the CMPSS
      4. 13.5.4 Enabling and Disabling the CMPSS Clock
    6. 13.6 CMPSS DAC Output
    7. 13.7 Software
      1. 13.7.1 CMPSS Examples
      2. 13.7.2 CMPSS_LITE Examples
        1. 13.7.2.1 CMPSSLITE Asynchronous Trip
    8. 13.8 CMPSS Registers
      1. 13.8.1 CMPSS Base Address Table
      2. 13.8.2 CMPSS_LITE_REGS Registers
  16. 14Programmable Gain Amplifier (PGA)
    1. 14.1  Programmable Gain Amplifier (PGA) Overview
      1. 14.1.1 Features
      2. 14.1.2 Block Diagram
    2. 14.2  Linear Output Range
    3. 14.3  Gain Values
    4. 14.4  Modes of Operation
      1. 14.4.1 Buffer Mode
      2. 14.4.2 Standalone Mode
      3. 14.4.3 Non-inverting Mode
      4. 14.4.4 Subtractor Mode
    5. 14.5  External Filtering
      1. 14.5.1 Low-Pass Filter Using Internal Filter Resistor and External Capacitor
      2. 14.5.2 Single Pole Low-Pass Filter Using Internal Gain Resistor and External Capacitor
    6. 14.6  Error Calibration
      1. 14.6.1 Offset Error
      2. 14.6.2 Gain Error
    7. 14.7  Chopping Feature
    8. 14.8  Enabling and Disabling the PGA Clock
    9. 14.9  Lock Register
    10. 14.10 Analog Front-End Integration
      1. 14.10.1 Analog-to-Digital Converter (ADC)
        1. 14.10.1.1 Unfiltered Acquisition Window
        2. 14.10.1.2 Filtered Acquisition Window
      2. 14.10.2 Comparator Subsystem (CMPSS)
      3. 14.10.3 Alternate Functions
    11. 14.11 Examples
      1. 14.11.1 Non-Inverting Amplifier Using Non-Inverting Mode
      2. 14.11.2 Buffer Mode
      3. 14.11.3 Low-Side Current Sensing
      4. 14.11.4 Bidirectional Current Sensing
    12. 14.12 Software
      1. 14.12.1 PGA Examples
        1. 14.12.1.1 PGA CMPSSDAC-ADC External Loopback Example
    13. 14.13 PGA Registers
      1. 14.13.1 PGA Base Address Table
      2. 14.13.2 PGA_REGS Registers
  17. 15Multi-Channel Pulse Width Modulator (MCPWM)
    1. 15.1  Introduction
      1. 15.1.1 PWM Related Collateral
      2. 15.1.2 Submodule Overview
    2. 15.2  Configuring Device Pins
    3. 15.3  MCPWM Modules Overview
    4. 15.4  Time-Base (TB) Submodule
      1. 15.4.1 Purpose of the Time-Base Submodule
      2. 15.4.2 Controlling and Monitoring the Time-Base Submodule
      3. 15.4.3 Calculating PWM Period and Frequency
        1. 15.4.3.1 Time-Base Period Shadow Register
        2. 15.4.3.2 Time-Base Clock Synchronization
        3. 15.4.3.3 Time-Base Counter Synchronization
        4. 15.4.3.4 MCPWM SYNC Selection
      4. 15.4.4 Phase Locking the Time-Base Clocks of Multiple MCPWM Modules
      5. 15.4.5 Time-Base Counter Modes and Timing Waveforms
      6. 15.4.6 Global Load
        1. 15.4.6.1 One-Shot Load Mode
    5. 15.5  Counter-Compare (CC) Submodule
      1. 15.5.1 Purpose of the Counter-Compare Submodule
      2. 15.5.2 Controlling and Monitoring the Counter-Compare Submodule
      3. 15.5.3 Operational Highlights for the Counter-Compare Submodule
      4. 15.5.4 Count Mode Timing Waveforms
    6. 15.6  Action-Qualifier (AQ) Submodule
      1. 15.6.1 Purpose of the Action-Qualifier Submodule
      2. 15.6.2 Action-Qualifier Submodule Control and Status Register Definitions
      3. 15.6.3 Action-Qualifier Event Priority
      4. 15.6.4 AQCTLA and AQCTLB Shadow Mode Operations
      5. 15.6.5 Configuration Requirements for Common Waveforms
    7. 15.7  Dead-Band Generator (DB) Submodule
      1. 15.7.1 Purpose of the Dead-Band Submodule
      2. 15.7.2 Dead-Band Submodule Additional Operating Modes
      3. 15.7.3 Operational Highlights for the Dead-Band Submodule
    8. 15.8  Trip-Zone (TZ) Submodule
      1. 15.8.1 Purpose of the Trip-Zone Submodule
      2. 15.8.2 Operational Highlights for the Trip-Zone Submodule
        1. 15.8.2.1 Trip-Zone Configurations
      3. 15.8.3 Generating Trip Event Interrupts
    9. 15.9  Event-Trigger (ET) Submodule
      1. 15.9.1 Operational Overview of the MCPWM Event-Trigger Submodule
    10. 15.10 PWM Crossbar (X-BAR)
    11. 15.11 Software
      1. 15.11.1 MCPWM Examples
        1. 15.11.1.1 MCPWM Basic PWM Generation and Updates
        2. 15.11.1.2 MCPWM Basic PWM Generation and Updates
        3. 15.11.1.3 MCPWM Basic PWM generation With DeadBand
        4. 15.11.1.4 MCPWM Basic PWM Generation and Updates without Sysconfig
        5. 15.11.1.5 MCPWM PWM Tripzone Feature Showcase
        6. 15.11.1.6 MCPWM Global Load Feature Showcase
        7. 15.11.1.7 MCPWM DMA Configuration for Dynamic PWM Control
    12. 15.12 MCPWM Registers
      1. 15.12.1 MCPWM Base Address Table
      2. 15.12.2 MCPWM_6CH_REGS Registers
      3. 15.12.3 MCPWM_2CH_REGS Registers
  18. 16Enhanced Capture (eCAP)
    1. 16.1 Introduction
      1. 16.1.1 Features
      2. 16.1.2 ECAP Related Collateral
    2. 16.2 Description
    3. 16.3 Configuring Device Pins for the eCAP
    4. 16.4 Capture and APWM Operating Mode
    5. 16.5 Capture Mode Description
      1. 16.5.1 Event Prescaler
      2. 16.5.2 Edge Polarity Select and Qualifier
      3. 16.5.3 Continuous/One-Shot Control
      4. 16.5.4 32-Bit Counter and Phase Control
      5. 16.5.5 CAP1-CAP4 Registers
      6. 16.5.6 eCAP Synchronization
        1. 16.5.6.1 Example 1 - Using SWSYNC with ECAP Module
      7. 16.5.7 Interrupt Control
      8. 16.5.8 Shadow Load and Lockout Control
      9. 16.5.9 APWM Mode Operation
    6. 16.6 Application of the eCAP Module
      1. 16.6.1 Example 1 - Absolute Time-Stamp Operation Rising-Edge Trigger
      2. 16.6.2 Example 2 - Absolute Time-Stamp Operation Rising- and Falling-Edge Trigger
      3. 16.6.3 Example 3 - Time Difference (Delta) Operation Rising-Edge Trigger
      4. 16.6.4 Example 4 - Time Difference (Delta) Operation Rising- and Falling-Edge Trigger
    7. 16.7 Application of the APWM Mode
      1. 16.7.1 Example 1 - Simple PWM Generation (Independent Channels)
    8. 16.8 Software
      1. 16.8.1 ECAP Examples
        1. 16.8.1.1 eCAP APWM Example
        2. 16.8.1.2 eCAP Capture PWM Example
    9. 16.9 ECAP Registers
      1. 16.9.1 ECAP Base Address Table
      2. 16.9.2 ECAP_REGS Registers
  19. 17Enhanced Quadrature Encoder Pulse (eQEP)
    1. 17.1  Introduction
      1. 17.1.1 EQEP Related Collateral
    2. 17.2  Configuring Device Pins
    3. 17.3  Description
      1. 17.3.1 EQEP Inputs
      2. 17.3.2 Functional Description
      3. 17.3.3 eQEP Memory Map
    4. 17.4  Quadrature Decoder Unit (QDU)
      1. 17.4.1 Position Counter Input Modes
        1. 17.4.1.1 Quadrature Count Mode
        2. 17.4.1.2 Direction-Count Mode
        3. 17.4.1.3 Up-Count Mode
        4. 17.4.1.4 Down-Count Mode
      2. 17.4.2 eQEP Input Polarity Selection
      3. 17.4.3 Position-Compare Sync Output
    5. 17.5  Position Counter and Control Unit (PCCU)
      1. 17.5.1 Position Counter Operating Modes
        1. 17.5.1.1 Position Counter Reset on Index Event (QEPCTL[PCRM] = 00)
        2. 17.5.1.2 Position Counter Reset on Maximum Position (QEPCTL[PCRM] = 01)
        3. 17.5.1.3 Position Counter Reset on the First Index Event (QEPCTL[PCRM] = 10)
        4. 17.5.1.4 Position Counter Reset on Unit Time-out Event (QEPCTL[PCRM] = 11)
      2. 17.5.2 Position Counter Latch
        1. 17.5.2.1 Index Event Latch
        2. 17.5.2.2 Strobe Event Latch
      3. 17.5.3 Position Counter Initialization
      4. 17.5.4 eQEP Position-compare Unit
    6. 17.6  eQEP Edge Capture Unit
    7. 17.7  eQEP Watchdog
    8. 17.8  eQEP Unit Timer Base
    9. 17.9  QMA Module
      1. 17.9.1 Modes of Operation
        1. 17.9.1.1 QMA Mode-1 (QMACTRL[MODE] = 1)
        2. 17.9.1.2 QMA Mode-2 (QMACTRL[MODE] = 2)
      2. 17.9.2 Interrupt and Error Generation
    10. 17.10 eQEP Interrupt Structure
    11. 17.11 Software
      1. 17.11.1 EQEP Examples
        1. 17.11.1.1 Frequency Measurement Using eQEP
        2. 17.11.1.2 Position and Speed Measurement Using eQEP
        3. 17.11.1.3 Frequency Measurement Using eQEP via unit timeout interrupt
        4. 17.11.1.4 Motor speed and direction measurement using eQEP via unit timeout interrupt
    12. 17.12 EQEP Registers
      1. 17.12.1 EQEP Base Address Table
      2. 17.12.2 EQEP_REGS Registers
  20. 18Universal Asynchronous Receiver/Transmitter (UART)
    1. 18.1 Introduction
      1. 18.1.1 Features
      2. 18.1.2 Block Diagram
    2. 18.2 Functional Description
      1. 18.2.1 Transmit and Receive Logic
      2. 18.2.2 Baud-Rate Generation
      3. 18.2.3 Data Transmission
      4. 18.2.4 Serial IR (SIR)
      5. 18.2.5 9-Bit UART Mode
      6. 18.2.6 FIFO Operation
      7. 18.2.7 Interrupts
      8. 18.2.8 Loopback Operation
      9. 18.2.9 DMA Operation
        1. 18.2.9.1 Receiving Data Using UART with DMA
        2. 18.2.9.2 Transmitting Data Using UART with DMA
    3. 18.3 Initialization and Configuration
    4. 18.4 Software
      1. 18.4.1 UART Examples
        1. 18.4.1.1 UART Echoback
        2. 18.4.1.2 UART Loopback
        3. 18.4.1.3 UART Loopback with interrupt
        4. 18.4.1.4 UART Digital Loopback with DMA
    5. 18.5 UART Registers
      1. 18.5.1 UART Base Address Table
      2. 18.5.2 UART_REGS Registers
      3. 18.5.3 UART_REGS_WRITE Registers
  21. 19Serial Peripheral Interface (SPI)
    1. 19.1 Introduction
      1. 19.1.1 Features
      2. 19.1.2 Block Diagram
    2. 19.2 System-Level Integration
      1. 19.2.1 SPI Module Signals
      2. 19.2.2 Configuring Device Pins
        1. 19.2.2.1 GPIOs Required for High-Speed Mode
      3. 19.2.3 SPI Interrupts
      4. 19.2.4 DMA Support
    3. 19.3 SPI Operation
      1. 19.3.1  Introduction to Operation
      2. 19.3.2  Controller Mode
      3. 19.3.3  Peripheral Mode
      4. 19.3.4  Data Format
        1. 19.3.4.1 Transmission of Bit from SPIRXBUF
      5. 19.3.5  Baud Rate Selection
        1. 19.3.5.1 Baud Rate Determination
        2. 19.3.5.2 Baud Rate Calculation in Non-High Speed Mode (HS_MODE = 0)
      6. 19.3.6  SPI Clocking Schemes
      7. 19.3.7  SPI FIFO Description
      8. 19.3.8  SPI DMA Transfers
        1. 19.3.8.1 Transmitting Data Using SPI with DMA
        2. 19.3.8.2 Receiving Data Using SPI with DMA
      9. 19.3.9  SPI High-Speed Mode
      10. 19.3.10 SPI 3-Wire Mode Description
    4. 19.4 Programming Procedure
      1. 19.4.1 Initialization Upon Reset
      2. 19.4.2 Configuring the SPI
      3. 19.4.3 Configuring the SPI for High-Speed Mode
      4. 19.4.4 Data Transfer Example
      5. 19.4.5 SPI 3-Wire Mode Code Examples
        1. 19.4.5.1 3-Wire Controller Mode Transmit
        2.       679
          1. 19.4.5.2.1 3-Wire Controller Mode Receive
        3.       681
          1. 19.4.5.2.1 3-Wire Peripheral Mode Transmit
        4.       683
          1. 19.4.5.2.1 3-Wire Peripheral Mode Receive
      6. 19.4.6 SPI STEINV Bit in Digital Audio Transfers
    5. 19.5 Software
      1. 19.5.1 SPI Examples
        1. 19.5.1.1 SPI Digital Loopback
        2. 19.5.1.2 SPI Digital Loopback with FIFO Interrupts
        3. 19.5.1.3 SPI Digital Loopback with DMA
        4. 19.5.1.4 SPI EEPROM
        5. 19.5.1.5 SPI DMA EEPROM
    6. 19.6 SPI Registers
      1. 19.6.1 SPI Base Address Table
      2. 19.6.2 SPI_REGS Registers
  22. 20Inter-Integrated Circuit Module (I2C)
    1. 20.1 Introduction
      1. 20.1.1 I2C Related Collateral
      2. 20.1.2 Features
      3. 20.1.3 Features Not Supported
      4. 20.1.4 Functional Overview
      5. 20.1.5 Clock Generation
      6. 20.1.6 I2C Clock Divider Registers (I2CCLKL and I2CCLKH)
        1. 20.1.6.1 Formula for the Controller Clock Period
    2. 20.2 Configuring Device Pins
    3. 20.3 I2C Module Operational Details
      1. 20.3.1  Input and Output Voltage Levels
      2. 20.3.2  Selecting Pullup Resistors
      3. 20.3.3  Data Validity
      4. 20.3.4  Operating Modes
      5. 20.3.5  I2C Module START and STOP Conditions
      6. 20.3.6  Non-repeat Mode versus Repeat Mode
      7. 20.3.7  Serial Data Formats
        1. 20.3.7.1 7-Bit Addressing Format
        2. 20.3.7.2 10-Bit Addressing Format
        3. 20.3.7.3 Free Data Format
        4. 20.3.7.4 Using a Repeated START Condition
      8. 20.3.8  Clock Synchronization
      9. 20.3.9  Clock Stretching
      10. 20.3.10 Arbitration
      11. 20.3.11 Digital Loopback Mode
      12. 20.3.12 NACK Bit Generation
    4. 20.4 Interrupt Requests Generated by the I2C Module
      1. 20.4.1 Basic I2C Interrupt Requests
      2. 20.4.2 I2C FIFO Interrupts
    5. 20.5 Resetting or Disabling the I2C Module
    6. 20.6 Software
      1. 20.6.1 I2C Registers to Driverlib Functions
      2. 20.6.2 I2C Examples
        1. 20.6.2.1 C28x-I2C Library source file for FIFO interrupts
        2. 20.6.2.2 C28x-I2C Library source file for FIFO using polling
        3. 20.6.2.3 I2C Digital Loopback with FIFO Interrupts
        4. 20.6.2.4 I2C EEPROM
        5. 20.6.2.5 I2C EEPROM
        6. 20.6.2.6 I2C EEPROM
    7. 20.7 I2C Registers
      1. 20.7.1 I2C Base Address Table
      2. 20.7.2 I2C_REGS Registers
  23. 21Serial Communications Interface (SCI)
    1. 21.1  Introduction
      1. 21.1.1 Features
      2. 21.1.2 SCI Related Collateral
      3. 21.1.3 Block Diagram
    2. 21.2  Architecture
    3. 21.3  SCI Module Signal Summary
    4. 21.4  Configuring Device Pins
    5. 21.5  Multiprocessor and Asynchronous Communication Modes
    6. 21.6  SCI Programmable Data Format
    7. 21.7  SCI Multiprocessor Communication
      1. 21.7.1 Recognizing the Address Byte
      2. 21.7.2 Controlling the SCI TX and RX Features
      3. 21.7.3 Receipt Sequence
    8. 21.8  Idle-Line Multiprocessor Mode
      1. 21.8.1 Idle-Line Mode Steps
      2. 21.8.2 Block Start Signal
      3. 21.8.3 Wake-Up Temporary (WUT) Flag
        1. 21.8.3.1 Sending a Block Start Signal
      4. 21.8.4 Receiver Operation
    9. 21.9  Address-Bit Multiprocessor Mode
      1. 21.9.1 Sending an Address
    10. 21.10 SCI Communication Format
      1. 21.10.1 Receiver Signals in Communication Modes
      2. 21.10.2 Transmitter Signals in Communication Modes
    11. 21.11 SCI Port Interrupts
      1. 21.11.1 Break Detect
    12. 21.12 SCI Baud Rate Calculations
    13. 21.13 SCI Enhanced Features
      1. 21.13.1 SCI FIFO Description
      2. 21.13.2 SCI Auto-Baud
      3. 21.13.3 Autobaud-Detect Sequence
    14. 21.14 Software
      1. 21.14.1 SCI Examples
        1. 21.14.1.1 Tune Baud Rate via UART Example
        2. 21.14.1.2 SCI FIFO Digital Loop Back
        3. 21.14.1.3 SCI Digital Loop Back with Interrupts
        4. 21.14.1.4 SCI Echoback
        5. 21.14.1.5 stdout redirect example
    15. 21.15 SCI Registers
      1. 21.15.1 SCI Base Address Table
      2. 21.15.2 SCI_REGS Registers
  24. 22Revision History

9.3.4 PWM_XBAR_REGS Registers

Table 9-36 lists the memory-mapped registers for the PWM_XBAR_REGS registers. All register offset addresses not listed in Table 9-36 should be considered as reserved locations and the register contents should not be modified.

Table 9-36 PWM_XBAR_REGS Registers
OffsetAcronymRegister NameWrite Protection
0hTRIP1MUX0TO15CFGPWM XBAR Mux Configuration for Output1EALLOW
2hTRIP1MUX16TO31CFGPWM XBAR Mux Configuration for Output1EALLOW
4hTRIP2MUX0TO15CFGPWM XBAR Mux Configuration for Output2EALLOW
6hTRIP2MUX16TO31CFGPWM XBAR Mux Configuration for Output2EALLOW
8hTRIP3MUX0TO15CFGPWM XBAR Mux Configuration for Output3EALLOW
AhTRIP3MUX16TO31CFGPWM XBAR Mux Configuration for Output3EALLOW
ChTRIP4MUX0TO15CFGPWM XBAR Mux Configuration for Output4EALLOW
EhTRIP4MUX16TO31CFGPWM XBAR Mux Configuration for Output4EALLOW
10hTRIP5MUX0TO15CFGPWM XBAR Mux Configuration for Output5EALLOW
12hTRIP5MUX16TO31CFGPWM XBAR Mux Configuration for Output5EALLOW
14hTRIP6MUX0TO15CFGPWM XBAR Mux Configuration for Output6EALLOW
16hTRIP6MUX16TO31CFGPWM XBAR Mux Configuration for Output6EALLOW
18hTRIP7MUX0TO15CFGPWM XBAR Mux Configuration for Output7EALLOW
1AhTRIP7MUX16TO31CFGPWM XBAR Mux Configuration for Output7EALLOW
1ChTRIP8MUX0TO15CFGPWM XBAR Mux Configuration for Output8EALLOW
1EhTRIP8MUX16TO31CFGPWM XBAR Mux Configuration for Output8EALLOW
20hTRIP1MUXENABLEPWM XBAR Mux Enable for Output1EALLOW
22hTRIP2MUXENABLEPWM XBAR Mux Enable for Output2EALLOW
24hTRIP3MUXENABLEPWM XBAR Mux Enable for Output3EALLOW
26hTRIP4MUXENABLEPWM XBAR Mux Enable for Output4EALLOW
28hTRIP5MUXENABLEPWM XBAR Mux Enable for Output5EALLOW
2AhTRIP6MUXENABLEPWM XBAR Mux Enable for Output6EALLOW
2ChTRIP7MUXENABLEPWM XBAR Mux Enable for Output7EALLOW
2EhTRIP8MUXENABLEPWM XBAR Mux Enable for Output8EALLOW
38hTRIPOUTINVPWM XBAR Output Inversion RegisterEALLOW
3EhTRIPLOCKPWM XBAR Configuration Lock registerEALLOW

Complex bit access types are encoded to fit into small table cells. Table 9-37 shows the codes that are used for access types in this section.

Table 9-37 PWM_XBAR_REGS Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
R-0R
-0		Read
Returns 0s
Write Type
WWWrite
WSonceW
Sonce		Write
Set once
Reset or Default Value
-nValue after reset or the default value
Register Array Variables
i,j,k,l,m,nWhen these variables are used in a register name, an offset, or an address, they refer to the value of a register array where the register is part of a group of repeating registers. The register groups form a hierarchical structure and the array is represented with a formula.
yWhen this variable is used in a register name, an offset, or an address it refers to the value of a register array.

9.3.4.1 TRIP1MUX0TO15CFG Register (Offset = 0h) [Reset = 00000000h]

TRIP1MUX0TO15CFG is shown in Figure 9-32 and described in Table 9-38.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output1

Figure 9-32 TRIP1MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-38 TRIP1MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT1MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT1MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT1MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT1MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT1MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT1MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT1MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT1MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT1MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT1MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT1MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT1MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT1MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT1MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT1MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT1MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.2 TRIP1MUX16TO31CFG Register (Offset = 2h) [Reset = 00000000h]

TRIP1MUX16TO31CFG is shown in Figure 9-33 and described in Table 9-39.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output1

Figure 9-33 TRIP1MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-39 TRIP1MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT1MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT1MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.3 TRIP2MUX0TO15CFG Register (Offset = 4h) [Reset = 00000000h]

TRIP2MUX0TO15CFG is shown in Figure 9-34 and described in Table 9-40.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output2

Figure 9-34 TRIP2MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-40 TRIP2MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT2MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT2MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT2MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT2MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT2MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT2MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT2MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT2MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT2MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT2MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT2MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT2MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT2MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT2MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT2MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT2MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.4 TRIP2MUX16TO31CFG Register (Offset = 6h) [Reset = 00000000h]

TRIP2MUX16TO31CFG is shown in Figure 9-35 and described in Table 9-41.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output2

Figure 9-35 TRIP2MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-41 TRIP2MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT2MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT2MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.5 TRIP3MUX0TO15CFG Register (Offset = 8h) [Reset = 00000000h]

TRIP3MUX0TO15CFG is shown in Figure 9-36 and described in Table 9-42.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output3

Figure 9-36 TRIP3MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-42 TRIP3MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT3MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT3MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT3MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT3MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT3MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT3MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT3MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT3MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT3MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT3MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT3MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT3MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT3MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT3MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT3MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT3MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.6 TRIP3MUX16TO31CFG Register (Offset = Ah) [Reset = 00000000h]

TRIP3MUX16TO31CFG is shown in Figure 9-37 and described in Table 9-43.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output3

Figure 9-37 TRIP3MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-43 TRIP3MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT3MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT3MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.7 TRIP4MUX0TO15CFG Register (Offset = Ch) [Reset = 00000000h]

TRIP4MUX0TO15CFG is shown in Figure 9-38 and described in Table 9-44.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output4

Figure 9-38 TRIP4MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-44 TRIP4MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT4MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT4MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT4MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT4MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT4MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT4MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT4MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT4MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT4MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT4MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT4MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT4MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT4MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT4MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT4MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT4MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.8 TRIP4MUX16TO31CFG Register (Offset = Eh) [Reset = 00000000h]

TRIP4MUX16TO31CFG is shown in Figure 9-39 and described in Table 9-45.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output4

Figure 9-39 TRIP4MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-45 TRIP4MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT4MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT4MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.9 TRIP5MUX0TO15CFG Register (Offset = 10h) [Reset = 00000000h]

TRIP5MUX0TO15CFG is shown in Figure 9-40 and described in Table 9-46.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output5

Figure 9-40 TRIP5MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-46 TRIP5MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT5MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT5MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT5MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT5MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT5MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT5MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT5MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT5MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT5MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT5MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT5MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT5MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT5MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT5MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT5MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT5MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.10 TRIP5MUX16TO31CFG Register (Offset = 12h) [Reset = 00000000h]

TRIP5MUX16TO31CFG is shown in Figure 9-41 and described in Table 9-47.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output5

Figure 9-41 TRIP5MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-47 TRIP5MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT5MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT5MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.11 TRIP6MUX0TO15CFG Register (Offset = 14h) [Reset = 00000000h]

TRIP6MUX0TO15CFG is shown in Figure 9-42 and described in Table 9-48.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output6

Figure 9-42 TRIP6MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-48 TRIP6MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT6MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT6MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT6MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT6MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT6MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT6MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT6MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT6MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT6MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT6MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT6MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT6MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT6MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT6MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT6MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT6MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.12 TRIP6MUX16TO31CFG Register (Offset = 16h) [Reset = 00000000h]

TRIP6MUX16TO31CFG is shown in Figure 9-43 and described in Table 9-49.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output6

Figure 9-43 TRIP6MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-49 TRIP6MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT6MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT6MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.13 TRIP7MUX0TO15CFG Register (Offset = 18h) [Reset = 00000000h]

TRIP7MUX0TO15CFG is shown in Figure 9-44 and described in Table 9-50.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output7

Figure 9-44 TRIP7MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-50 TRIP7MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT7MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT7MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT7MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT7MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT7MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT7MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT7MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT7MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT7MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT7MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT7MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT7MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT7MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT7MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT7MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT7MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.14 TRIP7MUX16TO31CFG Register (Offset = 1Ah) [Reset = 00000000h]

TRIP7MUX16TO31CFG is shown in Figure 9-45 and described in Table 9-51.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output7

Figure 9-45 TRIP7MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-51 TRIP7MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT7MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT7MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.15 TRIP8MUX0TO15CFG Register (Offset = 1Ch) [Reset = 00000000h]

TRIP8MUX0TO15CFG is shown in Figure 9-46 and described in Table 9-52.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output8

Figure 9-46 TRIP8MUX0TO15CFG Register
31302928272625242322212019181716
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-52 TRIP8MUX0TO15CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30MUX15R/W0hSelect Bits for PWM-XBAR OUT8MUX15:
00 : Select .0 input for MUX15
01 : Select .1 input for MUX15
10 : Select .2 input for MUX15
11 : Select .3 input for MUX15
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

29-28MUX14R/W0hSelect Bits for PWM-XBAR OUT8MUX14:
00 : Select .0 input for MUX14
01 : Select .1 input for MUX14
10 : Select .2 input for MUX14
11 : Select .3 input for MUX14
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

27-26MUX13R/W0hSelect Bits for PWM-XBAR OUT8MUX13:
00 : Select .0 input for MUX13
01 : Select .1 input for MUX13
10 : Select .2 input for MUX13
11 : Select .3 input for MUX13
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

25-24MUX12R/W0hSelect Bits for PWM-XBAR OUT8MUX12:
00 : Select .0 input for MUX12
01 : Select .1 input for MUX12
10 : Select .2 input for MUX12
11 : Select .3 input for MUX12
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

23-22MUX11R/W0hSelect Bits for PWM-XBAR OUT8MUX11:
00 : Select .0 input for MUX11
01 : Select .1 input for MUX11
10 : Select .2 input for MUX11
11 : Select .3 input for MUX11
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

21-20MUX10R/W0hSelect Bits for PWM-XBAR OUT8MUX10:
00 : Select .0 input for MUX10
01 : Select .1 input for MUX10
10 : Select .2 input for MUX10
11 : Select .3 input for MUX10
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

19-18MUX9R/W0hSelect Bits for PWM-XBAR OUT8MUX9:
00 : Select .0 input for MUX9
01 : Select .1 input for MUX9
10 : Select .2 input for MUX9
11 : Select .3 input for MUX9
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

17-16MUX8R/W0hSelect Bits for PWM-XBAR OUT8MUX8:
00 : Select .0 input for MUX8
01 : Select .1 input for MUX8
10 : Select .2 input for MUX8
11 : Select .3 input for MUX8
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15-14MUX7R/W0hSelect Bits for PWM-XBAR OUT8MUX7:
00 : Select .0 input for MUX7
01 : Select .1 input for MUX7
10 : Select .2 input for MUX7
11 : Select .3 input for MUX7
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13-12MUX6R/W0hSelect Bits for PWM-XBAR OUT8MUX6:
00 : Select .0 input for MUX6
01 : Select .1 input for MUX6
10 : Select .2 input for MUX6
11 : Select .3 input for MUX6
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11-10MUX5R/W0hSelect Bits for PWM-XBAR OUT8MUX5:
00 : Select .0 input for MUX5
01 : Select .1 input for MUX5
10 : Select .2 input for MUX5
11 : Select .3 input for MUX5
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9-8MUX4R/W0hSelect Bits for PWM-XBAR OUT8MUX4:
00 : Select .0 input for MUX4
01 : Select .1 input for MUX4
10 : Select .2 input for MUX4
11 : Select .3 input for MUX4
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7-6MUX3R/W0hSelect Bits for PWM-XBAR OUT8MUX3:
00 : Select .0 input for MUX3
01 : Select .1 input for MUX3
10 : Select .2 input for MUX3
11 : Select .3 input for MUX3
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5-4MUX2R/W0hSelect Bits for PWM-XBAR OUT8MUX2:
00 : Select .0 input for MUX2
01 : Select .1 input for MUX2
10 : Select .2 input for MUX2
11 : Select .3 input for MUX2
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3-2MUX1R/W0hSelect Bits for PWM-XBAR OUT8MUX1:
00 : Select .0 input for MUX1
01 : Select .1 input for MUX1
10 : Select .2 input for MUX1
11 : Select .3 input for MUX1
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX0R/W0hSelect Bits for PWM-XBAR OUT8MUX0:
00 : Select .0 input for MUX0
01 : Select .1 input for MUX0
10 : Select .2 input for MUX0
11 : Select .3 input for MUX0
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.16 TRIP8MUX16TO31CFG Register (Offset = 1Eh) [Reset = 00000000h]

TRIP8MUX16TO31CFG is shown in Figure 9-47 and described in Table 9-53.

Return to the Summary Table.

PWM XBAR Mux Configuration for Output8

Figure 9-47 TRIP8MUX16TO31CFG Register
31302928272625242322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
1514131211109876543210
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-53 TRIP8MUX16TO31CFG Register Field Descriptions
BitFieldTypeResetDescription
31-30RESERVEDR/W0hReserved
29-28RESERVEDR/W0hReserved
27-26RESERVEDR/W0hReserved
25-24RESERVEDR/W0hReserved
23-22RESERVEDR/W0hReserved
21-20RESERVEDR/W0hReserved
19-18RESERVEDR/W0hReserved
17-16RESERVEDR/W0hReserved
15-14RESERVEDR/W0hReserved
13-12RESERVEDR/W0hReserved
11-10RESERVEDR/W0hReserved
9-8RESERVEDR/W0hReserved
7-6RESERVEDR/W0hReserved
5-4RESERVEDR/W0hReserved
3-2MUX17R/W0hSelect Bits for PWM-XBAR OUT8MUX17:
00 : Select .0 input for MUX17
01 : Select .1 input for MUX17
10 : Select .2 input for MUX17
11 : Select .3 input for MUX17
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1-0MUX16R/W0hSelect Bits for PWM-XBAR OUT8MUX16:
00 : Select .0 input for MUX16
01 : Select .1 input for MUX16
10 : Select .2 input for MUX16
11 : Select .3 input for MUX16
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.17 TRIP1MUXENABLE Register (Offset = 20h) [Reset = 00000000h]

TRIP1MUXENABLE is shown in Figure 9-48 and described in Table 9-54.

Return to the Summary Table.

PWM XBAR Mux Enable for Output1

Figure 9-48 TRIP1MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-54 TRIP1MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT1 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT1 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT1 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT1 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT1 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT1 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT1 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT1 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT1 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT1 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT1 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT1 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT1 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT1 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT1 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT1 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT1 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT1 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT1 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT1 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.18 TRIP2MUXENABLE Register (Offset = 22h) [Reset = 00000000h]

TRIP2MUXENABLE is shown in Figure 9-49 and described in Table 9-55.

Return to the Summary Table.

PWM XBAR Mux Enable for Output2

Figure 9-49 TRIP2MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-55 TRIP2MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT2 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT2 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT2 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT2 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT2 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT2 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT2 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT2 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT2 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT2 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT2 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT2 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT2 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT2 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT2 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT2 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT2 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT2 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT2 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT2 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.19 TRIP3MUXENABLE Register (Offset = 24h) [Reset = 00000000h]

TRIP3MUXENABLE is shown in Figure 9-50 and described in Table 9-56.

Return to the Summary Table.

PWM XBAR Mux Enable for Output3

Figure 9-50 TRIP3MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-56 TRIP3MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT3 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT3 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT3 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT3 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT3 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT3 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT3 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT3 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT3 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT3 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT3 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT3 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT3 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT3 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT3 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT3 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT3 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT3 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT3 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT3 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.20 TRIP4MUXENABLE Register (Offset = 26h) [Reset = 00000000h]

TRIP4MUXENABLE is shown in Figure 9-51 and described in Table 9-57.

Return to the Summary Table.

PWM XBAR Mux Enable for Output4

Figure 9-51 TRIP4MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-57 TRIP4MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT4 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT4 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT4 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT4 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT4 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT4 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT4 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT4 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT4 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT4 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT4 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT4 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT4 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT4 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT4 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT4 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT4 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT4 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT4 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT4 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.21 TRIP5MUXENABLE Register (Offset = 28h) [Reset = 00000000h]

TRIP5MUXENABLE is shown in Figure 9-52 and described in Table 9-58.

Return to the Summary Table.

PWM XBAR Mux Enable for Output5

Figure 9-52 TRIP5MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-58 TRIP5MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT5 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT5 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT5 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT5 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT5 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT5 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT5 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT5 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT5 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT5 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT5 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT5 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT5 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT5 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT5 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT5 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT5 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT5 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT5 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT5 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.22 TRIP6MUXENABLE Register (Offset = 2Ah) [Reset = 00000000h]

TRIP6MUXENABLE is shown in Figure 9-53 and described in Table 9-59.

Return to the Summary Table.

PWM XBAR Mux Enable for Output6

Figure 9-53 TRIP6MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-59 TRIP6MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT6 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT6 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT6 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT6 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT6 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT6 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT6 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT6 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT6 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT6 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT6 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT6 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT6 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT6 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT6 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT6 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT6 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT6 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT6 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT6 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.23 TRIP7MUXENABLE Register (Offset = 2Ch) [Reset = 00000000h]

TRIP7MUXENABLE is shown in Figure 9-54 and described in Table 9-60.

Return to the Summary Table.

PWM XBAR Mux Enable for Output7

Figure 9-54 TRIP7MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-60 TRIP7MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT7 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT7 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT7 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT7 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT7 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT7 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT7 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT7 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT7 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT7 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT7 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT7 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT7 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT7 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT7 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT7 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT7 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT7 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT7 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT7 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.24 TRIP8MUXENABLE Register (Offset = 2Eh) [Reset = 00000000h]

TRIP8MUXENABLE is shown in Figure 9-55 and described in Table 9-61.

Return to the Summary Table.

PWM XBAR Mux Enable for Output8

Figure 9-55 TRIP8MUXENABLE Register
3130292827262524
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVED
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
2322212019181716
RESERVEDRESERVEDRESERVEDRESERVEDRESERVEDRESERVEDMUX17MUX16
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
15141312111098
MUX15MUX14MUX13MUX12MUX11MUX10MUX9MUX8
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
76543210
MUX7MUX6MUX5MUX4MUX3MUX2MUX1MUX0
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-61 TRIP8MUXENABLE Register Field Descriptions
BitFieldTypeResetDescription
31RESERVEDR/W0hReserved
30RESERVEDR/W0hReserved
29RESERVEDR/W0hReserved
28RESERVEDR/W0hReserved
27RESERVEDR/W0hReserved
26RESERVEDR/W0hReserved
25RESERVEDR/W0hReserved
24RESERVEDR/W0hReserved
23RESERVEDR/W0hReserved
22RESERVEDR/W0hReserved
21RESERVEDR/W0hReserved
20RESERVEDR/W0hReserved
19RESERVEDR/W0hReserved
18RESERVEDR/W0hReserved
17MUX17R/W0hSelects the output of MUX17 to drive OUT8 of PWM-XBAR
0: Respective output of MUX17 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX17 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

16MUX16R/W0hSelects the output of MUX16 to drive OUT8 of PWM-XBAR
0: Respective output of MUX16 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX16 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

15MUX15R/W0hSelects the output of MUX15 to drive OUT8 of PWM-XBAR
0: Respective output of MUX15 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX15 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

14MUX14R/W0hSelects the output of MUX14 to drive OUT8 of PWM-XBAR
0: Respective output of MUX14 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX14 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

13MUX13R/W0hSelects the output of MUX13 to drive OUT8 of PWM-XBAR
0: Respective output of MUX13 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX13 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

12MUX12R/W0hSelects the output of MUX12 to drive OUT8 of PWM-XBAR
0: Respective output of MUX12 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX12 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

11MUX11R/W0hSelects the output of MUX11 to drive OUT8 of PWM-XBAR
0: Respective output of MUX11 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX11 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

10MUX10R/W0hSelects the output of MUX10 to drive OUT8 of PWM-XBAR
0: Respective output of MUX10 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX10 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9MUX9R/W0hSelects the output of MUX9 to drive OUT8 of PWM-XBAR
0: Respective output of MUX9 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX9 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

8MUX8R/W0hSelects the output of MUX8 to drive OUT8 of PWM-XBAR
0: Respective output of MUX8 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX8 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

7MUX7R/W0hSelects the output of MUX7 to drive OUT8 of PWM-XBAR
0: Respective output of MUX7 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX7 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6MUX6R/W0hSelects the output of MUX6 to drive OUT8 of PWM-XBAR
0: Respective output of MUX6 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX6 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5MUX5R/W0hSelects the output of MUX5 to drive OUT8 of PWM-XBAR
0: Respective output of MUX5 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX5 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4MUX4R/W0hSelects the output of MUX4 to drive OUT8 of PWM-XBAR
0: Respective output of MUX4 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX4 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3MUX3R/W0hSelects the output of MUX3 to drive OUT8 of PWM-XBAR
0: Respective output of MUX3 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX3 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2MUX2R/W0hSelects the output of MUX2 to drive OUT8 of PWM-XBAR
0: Respective output of MUX2 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX2 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1MUX1R/W0hSelects the output of MUX1 to drive OUT8 of PWM-XBAR
0: Respective output of MUX1 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX1 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0MUX0R/W0hSelects the output of MUX0 to drive OUT8 of PWM-XBAR
0: Respective output of MUX0 is disabled to drive the OUT8 of PWM-XBAR
1: Respective output of MUX0 is enabled to drive the OUT8 of PWM-XBAR
Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.25 TRIPOUTINV Register (Offset = 38h) [Reset = 00000000h]

TRIPOUTINV is shown in Figure 9-56 and described in Table 9-62.

Return to the Summary Table.

PWM XBAR Output Inversion Register

Figure 9-56 TRIPOUTINV Register
3130292827262524
RESERVED
R-0-0h
2322212019181716
RESERVED
R-0-0h
15141312111098
RESERVED
R-0-0h
76543210
OUT8OUT7OUT6OUT5OUT4OUT3OUT2OUT1
R/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0hR/W-0h
Table 9-62 TRIPOUTINV Register Field Descriptions
BitFieldTypeResetDescription
31-16RESERVEDR-00hReserved
15-8RESERVEDR-00hReserved
7OUT8R/W0hSelects polarity for OUT8 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

6OUT7R/W0hSelects polarity for OUT7 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

5OUT6R/W0hSelects polarity for OUT6 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

4OUT5R/W0hSelects polarity for OUT5 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

3OUT4R/W0hSelects polarity for OUT4 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

2OUT3R/W0hSelects polarity for OUT3 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

1OUT2R/W0hSelects polarity for OUT2 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

0OUT1R/W0hSelects polarity for OUT1 of PWM-XBAR

0: drives active high output
1: drives active-low output

Refer to the PWM X-BAR section of this chapter for more details.

Reset type: CPU1.SYSRSn

9.3.4.26 TRIPLOCK Register (Offset = 3Eh) [Reset = 00000000h]

TRIPLOCK is shown in Figure 9-57 and described in Table 9-63.

Return to the Summary Table.

PWM XBAR Configuration Lock register

Figure 9-57 TRIPLOCK Register
3130292827262524
KEY
R-0/W-0h
2322212019181716
KEY
R-0/W-0h
15141312111098
RESERVED
R-0-0h
76543210
RESERVEDLOCK
R-0-0hR/WSonce-0h
Table 9-63 TRIPLOCK Register Field Descriptions
BitFieldTypeResetDescription
31-16KEYR-0/W0hBit-0 of this register can be set only if KEY= 0x5a5a

Reset type: CPU1.SYSRSn

15-1RESERVEDR-00hReserved
0LOCKR/WSonce0hLocks the configuration for PWM-XBAR. Once the configuration is locked, writes to the below registers for PWM-XBAR is blocked.

Registers Affected by the LOCK mechanism:
PWM-XBAROUTyMUX0TO15CFG
PWM-XBAROUTyMUX16TO31CFG
PWM-XBAROUTyMUXENABLE
PWM-XBAROUTLATEN
PWM-XBAROUTINV

0: Writes to the above registers are allowed
1: Writes to the above registers are blocked

Note:
[1] LOCK mechanism only apples to writes. Reads are never blocked.

Reset type: CPU1.SYSRSn