SNAS786C July   2020  – July 2025 CDCE6214-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  EEPROM Characteristics
    6. 5.6  Reference Input, Single-Ended Characteristics
    7. 5.7  Reference Input, Differential Characteristics
    8. 5.8  Reference Input, Crystal Mode Characteristics
    9. 5.9  General-Purpose Input Characteristics
    10. 5.10 Triple Level Input Characteristics
    11. 5.11 Logic Output Characteristics
    12. 5.12 Phase Locked Loop Characteristics
    13. 5.13 Closed-Loop Output Jitter Characteristics
    14. 5.14 Input and Output Isolation
    15. 5.15 Buffer Mode Characteristics
    16. 5.16 PCIe Spread Spectrum Generator
    17. 5.17 LVCMOS Output Characteristics
    18. 5.18 LP-HCSL Output Characteristics
    19. 5.19 LVDS Output Characteristics
    20. 5.20 Output Synchronization Characteristics
    21. 5.21 Power-On Reset Characteristics
    22. 5.22 I2C-Compatible Serial Interface Characteristics
    23. 5.23 Timing Requirements, I2C-Compatible Serial Interface
    24. 5.24 Power Supply Characteristics
    25. 5.25 Typical Characteristics
  7. 6 Parameter Measurement Information
    1. 6.1 Reference Inputs
    2. 6.2 Outputs
    3. 6.3 Serial Interface
    4. 6.4 PSNR Test
    5. 6.5 Clock Interfacing and Termination
      1. 6.5.1 Reference Input
      2. 6.5.2 Outputs
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Reference Block
        1. 7.3.1.1 Zero Delay Mode, Internal and External Path
      2. 7.3.2 Phase-Locked Loop (PLL)
        1. 7.3.2.1 PLL Configuration and Divider Settings
        2. 7.3.2.2 Spread Spectrum Clocking
        3. 7.3.2.3 Digitally-Controlled Oscillator and Frequency Increment or Decrement - Serial Interface Mode and GPIO Mode
      3. 7.3.3 Clock Distribution
        1. 7.3.3.1 Glitchless Operation
        2. 7.3.3.2 Divider Synchronization
        3. 7.3.3.3 Global and Individual Output Enable
      4. 7.3.4 Power Supplies and Power Management
      5. 7.3.5 Control Pins
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation Modes
        1. 7.4.1.1 Fall-Back Mode
        2. 7.4.1.2 Pin Mode
        3. 7.4.1.3 Serial Interface Mode
    5. 7.5 Programming
      1. 7.5.1 I2C Serial Interface
      2. 7.5.2 EEPROM
        1. 7.5.2.1 EEPROM - Cyclic Redundancy Check
        2. 7.5.2.2 Recommended Programming Procedure
        3. 7.5.2.3 EEPROM Access
          1. 7.5.2.3.1 Register Commit Flow
          2. 7.5.2.3.2 Direct Access Flow
        4. 7.5.2.4 Register Bits to EEPROM Mapping
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power-Up Sequence
      2. 8.3.2 Decoupling
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Examples
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
      2. 9.1.2 Device Nomenclature
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Package Option Addendum
    2. 11.2 Tape and Reel Information

7.4.1 Operation Modes

The operating modes listed in Table 7-18 can be set, and the GPIOs configured. An operating mode change only becomes effective when the change is loaded from the EEPROM after a power cycle.

Table 7-18 Modes of Operations
DESCRIPTIONMODEREFSELHW_SW_CTRLGPIO1GPIO2GPIO3GPIO4
I2C + GPIOFall-backMMI/OSDASCLI/O
M L/H I/O SDA SCL I/O
L/H M I/O SDA SCL I/O
OEPin ModeL/HL/HOE1OE2OE3OE4
I2C + GPIOSerial Interface ModeL/HL/HI/OSDASCLI/O