SPRAD67A december   2022  – july 2023 AM6411 , AM6412 , AM6421 , AM6422 , AM6441 , AM6442

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1 Introduction
    1. 1.1 Before Getting Started With the Board Design
    2. 1.2 Processor (Device) Selection
      1. 1.2.1 Availability of Tightly Coupled Memory (TCM)
    3. 1.3 Technical Documentation
    4. 1.4 Design Documentation
  5. 2 Block Diagram
    1. 2.1 Creating the Block Diagram
    2. 2.2 Selecting the Boot Mode
    3. 2.3 Confirming Pinmux (Multiplexing Compatibility)
  6. 3 Power Supply
    1. 3.1 Power Supply Architecture
      1. 3.1.1 Integrated Power Architecture
      2. 3.1.2 Discrete Power Architecture
    2. 3.2 Power (Supply) Rails
      1. 3.2.1 Core Supply
      2. 3.2.2 Peripheral Power Supply
      3. 3.2.3 Internal LDO for IO Groups (Processor IO Groups)
      4. 3.2.4 Dual-Voltage IOs (LVCMOS IOs / Processor IOs)
      5. 3.2.5 Dual-Voltage Dynamic Switching IOs for SDIO
      6. 3.2.6 VPP (eFuse ROM Programming Supply)
    3. 3.3 Determining Board Power Requirements
    4. 3.4 Power Supply Filters
    5. 3.5 Power Supply Decoupling and Bulk Capacitors
      1. 3.5.1 Note on PDN Target Impedance
    6. 3.6 Power Supply Sequencing
    7. 3.7 Supply Diagnostics
    8. 3.8 Power Supply Monitoring
  7. 4 Clocking
    1. 4.1 System Clock Input
    2. 4.2 Unused Clock Input
    3. 4.3 Clock Output
    4. 4.4 Single-ended Clock Source
    5. 4.5 Crystal Selection
  8. 5 JTAG (Joint Test Action Group)
    1. 5.1 JTAG / Emulation
      1. 5.1.1 Configuration of JTAG / Emulation
        1. 5.1.1.1 AM64x
        2. 5.1.1.2 AM243x
      2. 5.1.2 Implementation of JTAG / Emulation
      3. 5.1.3 JTAG Termination
  9. 6 Configuration (Processor) and Initialization (Processor and Device)
    1. 6.1 Processor Reset
    2. 6.2 Latching of the Boot Mode Configuration
    3. 6.3 Attach Device Reset
    4. 6.4 Watchdog Timer
  10. 7 Peripherals
    1. 7.1 Selecting Peripherals Across Domains
    2. 7.2 Memory
      1. 7.2.1 Processor DDR Subsystem and Device Register Configuration
    3. 7.3 Media and Data Storage Interfaces
    4. 7.4 Ethernet Interface
      1. 7.4.1 Common Platform Ethernet Switch 3-port Gigabit Ethernet (CPSW3G)
      2. 7.4.2 Programmable Real-Time Unit and Industrial Communication Subsystem - Gigabit (PRU_ICSSG)
    5. 7.5 Universal Serial Bus (USB) Subsystem
    6. 7.6 Peripheral Component Interconnect Express (PCIe) Subsystem
    7. 7.7 General Connectivity Peripherals
    8. 7.8 Analog-to-Digital Converter (ADC)
      1. 7.8.1 Change Summary of AM64x / AM243x SR2.0 ADC Errata
    9. 7.9 Termination of Power Pins, Unused Peripherals and IOs
      1. 7.9.1 External Interrupt (EXTINTn)
  11. 8 Interfacing of IO Buffers and Simulations
    1. 8.1 AM64x
    2. 8.2 AM243x
  12. 9 Power Consumption and Thermal Analysis
    1. 9.1 Power Consumption
    2. 9.2 Maximum Current for Different Supply Rails
    3. 9.3 Power Modes
    4. 9.4 Guidance on Thermal Design
      1. 9.4.1 AM64x
      2. 9.4.2 AM243x
  13. 10Schematic Capture and Review
    1. 10.1 Selection of Components and Components Value
    2. 10.2 Schematic Capture
    3. 10.3 Reviewing the Schematics
  14. 11Floor Planning, Layout and Routing Guidelines
    1. 11.1 Escape Routing Guidelines
    2. 11.2 DDR Layout Guidelines
    3. 11.3 High-Speed Differential Signal Routing Guidance
    4. 11.4 Additional References for Simulation
  15. 12Device Handling and Assembly
  16. 13References
    1. 13.1 AM64x
    2. 13.2 AM243x
    3. 13.3 Common
  17. 14Terminology
  18. 15Revision History

3.2.6 VPP (eFuse ROM Programming Supply)

This supply (1.8 V) is only sourced while programming the eFuse. VPP pin can be left floating (HiZ) or terminated to ground during power-up/power-down sequences and during normal processor operation. The following hardware requirements must be met when programming keys in the OTP eFuses:

  • The VPP power supply must be ramped up after completion of proper processor power-up sequence.
  • The VPP supply has high current transients and local bulk capacitors are likely needed near the VPP pin to assist the LDO transient response.
  • Select the power supply with quick discharge capability or use a discharge resistor. A Maximum current of 400 mA is required for programming. It is recommended to use a fixed LDO with input supply (3.3 V) and enable input.
  • If an external power supply is used, the supply is applied after the processor power supplies are stable.
  • The VPP power supply must be disabled (left floating (HiZ) or grounded) when not programming the OTP registers.

For more information, see [FAQ] AM625 / AM623 Custom board hardware design – Queries regarding VPP eFuse programming power supply selection and application.

For more information, see the VPP Specifications for One-Time Programmable (OTP) eFuses section in the Specifications chapter of the device-specific data sheet.