For additional terms or required resources, click any title below to view the detail page where available.
EVALUATION BOARD Download 149
DAUGHTER CARD Download
The SmartRF Transceiver Evaluation Board (TrxEB) is intended to be used together with Texas Instruments’ low-power RF transceivers for evaluation, performance testing and software development.
The following transceiver evaluation modules are supported:
- MSP430F5438A microcontroller
- 64x128 pixels serial LCD
- 4 general purpose LEDs
- 5 push-buttons
- 256 kB serial flash
- Three-axis digital accelerometer
- Ambient Light Sensor
- Jumpers for current measurements
- Break-out pins
- Full-speed USB 2.0 interface
- SmartRF Studio Support
DEVELOPMENT KIT Download 299
The CC1121 Evaluation Module Kit for 868-915 MHz can be used in conjunction with the CC1120 Development Kit to evaluate the operation of the Perfomance Line RF-IC at these particular frequency bands. The CC1120DK is required for operation and needs to be ordered separately.
- 2 x CC1121 Evaluation Modules for 868-915 MHz
- Whip antennas
Complete RF reference designs for the evaluation modules are available online.
CODE EXAMPLE OR DEMO Download
The CC1120 development kit provides a complete hardware performance testing and software development platform for TI's Sub-1 GHz Performance Line devices. The development kit comes with a pre-programmed packet error rate test. RF range and robustness can be tested with different RF settings, and (...)
- 2 x SmartRF Transceiver EB (TrxEB)
- 2 x CC1120EM 868/915 MHz
- 2 x Pulse Antennas
- 1 x MSP430 Debug Probe (FET)
- 2 x Micro USB Cables
- 1 x Standard USB Cable
- 1 x 14-pin Flat Cable
- 4 x 1.5 Volt AA Batteries
SWRC253E.ZIP (561 KB) SOFTWARE PROGRAMMING TOOL Download
SMARTRFTM-STUDIO — SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)
SUPPORT SOFTWARE Download
- Link tests. Send and Receive packets between nodes.
- Antenna and radiation tests. Set the radio in continuous wave TX and RX states.
- A set of recommended/typical register settings for all devices.
- Read and write individual RF registers.
- Execute individual commands to control the radio.
- Detailed (...)
SWRC219C.ZIP (571 KB) DESIGN TOOL Download
Hardware design reviews for SimpleLink™ CC1xxx devices SIMPLELINK-SUB1GHZ-DESIGN-REVIEWS — To get started with the SimpleLink™ Sub-1GHz hardware design review process:
- Step 1: Before requesting a review, it is important that to review the technical documentation and design & development resources available on the corresponding product page (see CC1xxx product page links below).
- Step 2 (...)
CAD/CAE SYMBOL Download
SWRR145A.ZIP (4039 KB) REFERENCE DESIGNS Download
CC1120-CC1190EM 868MHz Reference Design
CC1120-CC1190EM868RD — This RF Layout Reference Design demonstrates good decoupling and layout techniques for a low power RF device operating in the 868 MHz frequency band. The design should be used in applications targeting compliance with EN 300 220 in the in the European 869.4-869.65 MHz frequency sub-band (g3). The (...)
REFERENCE DESIGNS Download
CC1120-CC1190EM 915MHz Reference Design
CC1120-CC1190EM915RD — This RF Layout Reference Design demonstrates good decoupling and layout techniques for a low power RF device operating in the 915 MHz frequency band. The design should be used in applications targeting compliance with FCC Section 15.247 in the in the 902-928 MHz frequency band. The maximum (...)
REFERENCE DESIGNS Download
CC112x SKY65367 EM 30 dBm 169 MHz Reference Design
CC112XSKY65367EM-RD — The CC112x SKY63367 169 MHz EM Reference Design contains schematics and layout files for the CC112x SKY63367 Evaluation Module. CC112x denotes that CC1120, CC1121 and CC1125 can be used in this reference design. This design demonstrates good techniques for CC112x decoupling and RF layout. For (...)