Top

Product details

Parameters

Number of series cells 1 Charge current (Max) (A) 0.75 Operating Vin (Max) (V) 6 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (Min) (V) 4.2 Battery charge voltage (Max) (V) 4.2 Absolute Vin (safety rating) (Max) ((V)) 6.5 Control interface I2C Features BAT temp thermistor monitoring (hot/cold profile) Operating Vin (Min) (V) 4.3 Rating Catalog open-in-new Find other Battery charger ICs

Package | Pins | Size

WSON (NHL) 14 16 mm² 4 x 4 open-in-new Find other Battery charger ICs

Features

  • Supports USB Charging Scheme
  • Integrated Pass Transistor
  • Near-Depleted Battery Preconditioning
  • Monitors Battery Temperature
  • Built-In 5.6 Hour Timer
  • Under Voltage and Over Voltage Lockout
  • Charge Status Indicators
  • Charge Current Monitor Analog Output
  • LDO Mode Operation can source 1 Amp
  • Continuous Over Current/Temperature Protection

Key Specifications

  • 1% Charger Voltage Accuracy Over
    0°C ≤ TJ ≤ 85°C
  • 4.3V to 6V Input Voltage Range
  • 100 mA to 750 mA Charge Current Range, in Charger Mode
  • 100 mA to 500 mA Charge Current Range, in USB Mode
  • WSON Package Power Dissipation:
    2.7W at TA = 25°C

All trademarks are the property of their respective owners.

open-in-new Find other Battery charger ICs

Description

The LP3947 is a complete charge management system that safely charges and maintains a Li-Ion battery from either USB power source or AC adaptor. In USB mode, the LP3947 supports charging in low power or high power mode. Alternatively, the LP3947 can take charge from AC adaptor. In both USB and AC adaptor modes, charge current, battery regulation voltage, and End of Charge (EOC) point can be selected via I2C interface. The LP3947 can also operate on default values that are pre-programmed in the factory. The battery temperature is monitored continuously at the Ts pin to safeguard against hazardous charging conditions. The charger also has under-voltage and over-voltage protection as well as an internal 5.6 hr timer to protect the battery. The pass transistor and charge current sensing resistor are all integrated inside the LP3947.

The LP3947 operates in four modes: pre-qualification, constant current, constant voltage and maintenance modes. There are two open drain outputs for status indication. An internal amplifier readily converts the charge current into a voltage. Also, the charger can operate in an LDO mode providing a maximum of 1.2 Amp to the load.

open-in-new Find other Battery charger ICs
Download

Technical documentation

star = Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 5
Type Title Date
* Data sheet LP3947 USB/AC Adaptor, Single Cell Li-Ion Battery Charger IC datasheet (Rev. B) Apr. 02, 2013
Technical article When to use rechargeable batteries in small battery applications Oct. 01, 2019
Technical article Should I use a linear charger or a switching charger? Oct. 31, 2015
Technical article Summertime and the livin' is easy Jun. 20, 2014
User guide AN-1341 LP3947 Evaluation Board (Rev. A) Apr. 30, 2013

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

CAD/CAE symbols

Package Pins Download
WSON (NHL) 14 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos