Product details

Number of channels (#) 1 Total supply voltage (Min) (+5V=5, +/-5V=10) 8 Total supply voltage (Max) (+5V=5, +/-5V=10) 60 Output current (Typ) (mA) 3000 GBW (Typ) (MHz) 1 Slew rate (Typ) (V/us) 10 Vos (offset voltage @ 25 C) (Max) (mV) 10 Offset drift (Typ) (uV/C) 30 Iq per channel (Typ) (mA) 17 Features Adj Current Limit, Shutdown Rating Catalog Operating temperature range (C) -40 to 85 Input bias current (Max) (pA) 500000 CMRR (Typ) (dB) 95 Rail-to-rail In to V- Architecture Bipolar
Number of channels (#) 1 Total supply voltage (Min) (+5V=5, +/-5V=10) 8 Total supply voltage (Max) (+5V=5, +/-5V=10) 60 Output current (Typ) (mA) 3000 GBW (Typ) (MHz) 1 Slew rate (Typ) (V/us) 10 Vos (offset voltage @ 25 C) (Max) (mV) 10 Offset drift (Typ) (uV/C) 30 Iq per channel (Typ) (mA) 17 Features Adj Current Limit, Shutdown Rating Catalog Operating temperature range (C) -40 to 85 Input bias current (Max) (pA) 500000 CMRR (Typ) (dB) 95 Rail-to-rail In to V- Architecture Bipolar
TO-220 (KC) 7 47 mm² 10.16 x 4.58 TO-220 (KVT) 7 84 mm² 10.16 x 8.26 TO-263 (KTW) 7 154 mm² 10.1 x 15.24
  • Wide supply range
    • Single supply: 8 V to 60 V
    • Dual supply: ±4 V to ±30 V
  • High-output current:
    • 3-A continuous
    • 5-A peak
  • Wide output voltage swing
  • Fully protected:
    • Thermal shutdown
    • Adjustable current limit
  • Output disable control˜
  • Thermal shutdown indicator
  • High slew rate: 10 V
  • Low quiescent current
  • Packages:
    • 7-lead TO-220, zip and straight leads
    • 7-lead DDPAK surface-mount
  • Wide supply range
    • Single supply: 8 V to 60 V
    • Dual supply: ±4 V to ±30 V
  • High-output current:
    • 3-A continuous
    • 5-A peak
  • Wide output voltage swing
  • Fully protected:
    • Thermal shutdown
    • Adjustable current limit
  • Output disable control˜
  • Thermal shutdown indicator
  • High slew rate: 10 V
  • Low quiescent current
  • Packages:
    • 7-lead TO-220, zip and straight leads
    • 7-lead DDPAK surface-mount

The OPA548 device is a low-cost, high-voltage, and high-current operational amplifier that is designed to drive a wide variety of loads. A laser-trimmed, monolithic, integrated circuit provides excellent low-level signal accuracy and high-output voltage and current.

The OPA548 operates from either single or dual supplies for design flexibility. In single-supply operation, the input common-mode range extends below ground.

The OPA548 is internally protected against overtemperature conditions and current overloads. In addition, the OPA548 is designed to provide an accurate, user-selected current limit. Unlike other designs that use a power resistor in series with the output current path, the OPA548 senses the load indirectly. The current limit is adjustable from 0 A to 5 A with an external resistor and potentiometer, or controllable digitally with a voltage-out or current-out DAC.

The Enable/Status (E/S) pin provides two functions. An input on the pin not only disables the output stage to effectively disconnect the load, but also reduces the quiescent current to conserve power. The E/S pin output can be monitored to determine if the OPA548 is in thermal shutdown.

The OPA548 device is available in an industry-standard 7-lead staggered and straight lead TO-220 package, and a 7-lead DDPAK surface-mount plastic power package. The copper tab allows easy mounting to a heat sink or circuit board for excellent thermal performance. The device is specified for operation over the extended industrial temperature range, –40°C to 85°C. A SPICE macromodel is available for design analysis.

The OPA548 device is a low-cost, high-voltage, and high-current operational amplifier that is designed to drive a wide variety of loads. A laser-trimmed, monolithic, integrated circuit provides excellent low-level signal accuracy and high-output voltage and current.

The OPA548 operates from either single or dual supplies for design flexibility. In single-supply operation, the input common-mode range extends below ground.

The OPA548 is internally protected against overtemperature conditions and current overloads. In addition, the OPA548 is designed to provide an accurate, user-selected current limit. Unlike other designs that use a power resistor in series with the output current path, the OPA548 senses the load indirectly. The current limit is adjustable from 0 A to 5 A with an external resistor and potentiometer, or controllable digitally with a voltage-out or current-out DAC.

The Enable/Status (E/S) pin provides two functions. An input on the pin not only disables the output stage to effectively disconnect the load, but also reduces the quiescent current to conserve power. The E/S pin output can be monitored to determine if the OPA548 is in thermal shutdown.

The OPA548 device is available in an industry-standard 7-lead staggered and straight lead TO-220 package, and a 7-lead DDPAK surface-mount plastic power package. The copper tab allows easy mounting to a heat sink or circuit board for excellent thermal performance. The device is specified for operation over the extended industrial temperature range, –40°C to 85°C. A SPICE macromodel is available for design analysis.

Download

Similar products you might be interested in

open-in-new Compare products
Pin-for-pin with same functionality to the compared device.
OPA549 ACTIVE High-Voltage, High-Current Op Amp, Excellent Output Swing This device offers higher current drive (8-A)

Technical documentation

star = Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 7
Type Title Date
* Data sheet OPA548 High-Voltage, High-Current Operational Amplifier datasheet (Rev. D) 18 Dec 2019
E-book An Engineer’s Guide to Designing with Precision Amplifiers 29 Apr 2021
E-book The Signal e-book: A compendium of blog posts on op amp design topics 28 Mar 2017
User guide OPA547EVM, OPA548EVM User's Guide 10 Nov 2015
Technical article Why correct voltage matters for op-amp PowerPads™ 06 Nov 2014
Application note DC MOTOR SPEED CONTROLLER: Control a DC Motor without Tachometer Feedback 27 Sep 2000
Application note Power Amplifier Stress and Power Handling Limitations 27 Sep 2000

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

OPA548EVM — OPA548 Evaluation Module

The OPA548EVM is a platform for evaluating the OPA548 in a variety of circuit configurations. Circuit configuations include inverting/non-inverting gain, single/dual power supply, internal/external load and external reference. Access is provided to the Enable/Shutdown pin and LED's provide visual (...)

In stock
Limit: 1
Simulation model

OPA548 TINA-TI Reference Design (Rev. C)

SBOC114C.TSC (116 KB) - TINA-TI Reference Design
Simulation model

OPA548 PSpice Model (Rev. B)

SBOM088B.ZIP (39 KB) - PSpice Model
Simulation model

OPA548 TINA-TI Spice Model (Rev. B)

SBOM191B.ZIP (4 KB) - TINA-TI Spice Model
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Simulation tool

TINA-TI — SPICE-based analog simulation program

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
Calculation tool

ANALOG-ENGINEER-CALC — Analog engineer's calculator

The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
Package Pins Download
DDPAK/TO-263 (KTW) 7 View options
TO-220 (KC) 7 View options
TO-220 (KVT) 7 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos