Top

Product details

Parameters

Architecture FET / CMOS Input, Voltage FB Number of channels (#) 1 Total supply voltage (Min) (+5V=5, +/-5V=10) 2.2 Total supply voltage (Max) (+5V=5, +/-5V=10) 5.5 GBW (Typ) (MHz) 50 BW @ Acl (MHz) 50 Acl, min spec gain (V/V) 6 Slew rate (Typ) (V/us) 24 Vn at flatband (Typ) (nV/rtHz) 3.8 Vn at 1 kHz (Typ) (nV/rtHz) 3.8 Iq per channel (Typ) (mA) 0.9 Vos (offset voltage @ 25 C) (Max) (mV) 0.6 Rail-to-rail In to V-, Out Features Shutdown, Decompensated Rating Catalog Operating temperature range (C) -40 to 125 CMRR (Typ) (dB) 100 Input bias current (Max) (pA) 10 Offset drift (Typ) (uV/C) 0.3 Output current (Typ) (mA) 20 2nd harmonic (dBc) -105 3rd harmonic (dBc) -95 @ MHz 0.02 open-in-new Find other High-speed op amps (GBW>=50MHz)

Package | Pins | Size

SOT-23 (DBV) 5 5 mm² 2.9 x 1.6 SOT-SC70 (DCK) 6 4 mm² 2 x 2.1 open-in-new Find other High-speed op amps (GBW>=50MHz)

Features

  • Gain Bandwidth Product: 50 MHz
  • Quiescent Current: 900 µA (Typical)
  • Broadband Noise: 3.8 nV/√Hz
  • Input Offset Drift: 1.5 µV/°C (Maximum)
  • Offset Voltage: 120 µV (Typical)
  • Input Bias Current: 10 pA (Maximum)
  • Rail-to-Rail Output (RRO)
  • Decompensated, Gain ≥ 6 V/V (Stable)
  • Shutdown Current: 1 µA (Maximum)
  • Supply Range: 2.2 V to 5.5 V

All trademarks are the property of their respective owners.

open-in-new Find other High-speed op amps (GBW>=50MHz)

Description

The OPA607 and OPA2607 devices are decompensated minimum gain of 6 V/V stable, general-purpose CMOS operational amplifier with low noise of 3.8 nV/√ Hz and a wide gain bandwidth of 50 MHz. The low noise and wide bandwidth of the OPAx607 devices make them attractive for general-purpose applications which require a good balance between cost and performance. The high-impedance CMOS inputs make the OPAx607 devices an ideal amplifier to interface with sensors with high output impedance (for example, piezoelectric transducers).

The OPAx607 devices feature a Power-down mode with a maximum quiescent current of less than 1 µA, making the device suitable for use in portable battery-powered applications. The rail-to-rail output (RRO) of the OPAx607 devices can swing up to 8 mV from the supply rails, maximizing dynamic range.

The OPAx607 is optimized for low supply voltage operation as low as 2.2 V (±1.1 V) and up to 5.5 V (±2.75 V), and is specified over the temperature range of –40°C to +125°C.

open-in-new Find other High-speed op amps (GBW>=50MHz)
Download

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 7
Type Title Date
* Datasheet OPA607 50-MHz, Low-Power, Gain of 6-V/V Stable, Rail-to-Rail Output CMOS Op-Amp datasheet (Rev. F) Sep. 11, 2020
Technical articles 3 common questions when designing with high-speed amplifiers Jul. 17, 2020
User guides DEM-OPA-SC-1A-EVM Evaluation Module Oct. 23, 2019
Technical articles How to reduce distortion in high-voltage, high-frequency signal generation for AWGs Oct. 30, 2018
Technical articles What are the advantages of using JFET-input amplifiers in high-speed applications? Jun. 18, 2018
Technical articles Unique active mux capability combines buffer and switch into one solution Oct. 10, 2017
Application notes Noise Analysis for High Speed Op Amps (Rev. A) Jan. 17, 2005

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARDS Download
document-generic User guide
20
Description
The DEM-OPA-SC-1A-EVM is a demonstration fixture that helps designers evaluate the operation and performance of TI's high speed, wide bandwidth operational amplifiers. This unpopulated PC board is compatible with products offered in the SC70 (DCK) package using either the 5 pin or 6 pin variants.
Features
  • Configured for split supply operation and modified for single supply
  • Configurable for inverting and non-inverting gain configurations
  • Includes connections for termination resistors to match to standard 50-Ω input/output impedance test equipment
  • Inputs and Outputs use standard SMA connector footprints
  • (...)

Design tools & simulation

SIMULATION MODELS Download
SBOMB17B.TSC (1282 KB) - TINA-TI Reference Design
SIMULATION MODELS Download
SBOMB65A.ZIP (71 KB) - PSpice Model
SIMULATION TOOLS Download
PSpice® for TI design and simulation tool
PSPICE-FOR-TI — PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Features
  • Leverages Cadence PSpice Technology
  • Preinstalled library with a suite of digital models to enable worst-case timing analysis
  • Dynamic updates ensure you have access to most current device models
  • Optimized for simulation speed without loss of accuracy
  • Supports simultaneous analysis of multiple products
  • (...)
SIMULATION TOOLS Download
SPICE-based analog simulation program
TINA-TI TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
document-generic User guide
CALCULATION TOOLS Download
Analog engineer's calculator
ANALOG-ENGINEER-CALC — The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
Features
  • Expedites circuit design with analog-to-digital converters (ADCs) and digital-to-analog converters (DACs)
    • Noise calculations
    • Common unit translation
  • Solves common amplifier circuit design problems
    • Gain selections using standard resistors
    • Filter configurations
    • Total noise for common amplifier configurations
  • (...)
CALCULATION TOOLS Download
Voltage Divider Determines A Set of Resistors for a Voltage Divider
VOLT-DIVIDER-CALC VOLT-DIVIDER-CALC quickly determines a set of resistors for a voltage divider. This KnowledgeBase Javascript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. This calculator can also be used to design non-inverting attentuation circuits.

(...)

CAD/CAE symbols

Package Pins Download
SC70 (DCK) 6 View options
SOT-23 (DBV) 5 View options

Ordering & quality

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

Related videos