4.5V to 18V Input, 20A Synchronous Buck Controller with Power Good, 600kHz

A newer version of this product is available
open-in-new Compare products
Same functionality but is not pin-for-pin or parametrically equivalent to the compared device:
TPS40345 ACTIVE 3V to 20V Input, 25A, Synchronous Buck Controller with FSS, 600kHz This upgraded product offer a wider input range.

Product details


Vin (Min) (V) 4.5 Vin (Max) (V) 18 Vout (Min) (V) 0.591 Vout (Max) (V) 14.4 Iout (Max) (A) 20 Iq (Typ) (uA) 2500 Switching frequency (Min) (kHz) 600 Switching frequency (Max) (kHz) 600 Features Enable, Power Good, Pre-Bias Start-Up, Synchronous Rectification Operating temperature range (C) -40 to 85 Regulated outputs (#) 1 Number of Phases 1 Rating Catalog open-in-new Find other Buck controllers (external switch)

Package | Pins | Size

VSON (DRC) 10 9 mm² 3 x 3 open-in-new Find other Buck controllers (external switch)


  • Input Operating Voltage Range: 4.5 V to 18 V
  • Up to 20-A Output Currents
  • Supports Pre-Biased Outputs
  • 0.5%, 591-mV Reference
  • Switching Frequency
    • TPS40192: 600 kHz
    • TPS40193: 300 kHz
  • Three Selectable Thermally Compensated Short-Circuit Protection Levels
  • Hiccup Restart from Faults
  • Internal 5-V Regulator
  • High-Side and Low-Side MOSFET ON-resistance (RDS(on)) Current Sensing
  • 10-Pin 3 mm × 3 mm SON Package
  • Internal 4-ms Soft-Start Time
  • Thermal Shutdown Protection at 145°C

All trademarks are the property of their respective owners.

open-in-new Find other Buck controllers (external switch)


TPS40192 and TPS40193 are cost-optimized synchronous buck controllers that operate from 4.5 V to 18 V input. These controllers implement a voltage-mode control architecture with the switching frequency fixed at either 600 kHz (TPS40192) or 300 kHz (TPS40193). The higher switching frequency facilitates the use of smaller inductor and output capacitors, thereby providing a compact power-supply solution. An adaptive anti-cross conduction scheme is used to prevent shoot through current in the power FETs.

Short circuit detection is done by sensing the voltage drop across the low-side MOSFET when it is on and comparing it with a user selected threshold of 100 mV, 200 mV or 280 mV. The threshold is set with a single external resistor connected from COMP to GND. This resistor is sensed at startup and the selected threshold is latched. Pulse-by-pulse limiting (to prevent current runaway) is provided by sensing the voltage across the high-side MOSFET when it is on and terminating the cycle when the voltage drop rises above a fixed threshold of 550 mV. When the controller senses an output short circuit, both MOSFETs are turned off and a timeout period is observed before attempting to restart. This behavior provides limited power dissipation in the event of a sustained fault.

open-in-new Find other Buck controllers (external switch)

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 11
Type Title Date
* Datasheet TPS4019x 4.5-V to 18-V Input, Voltage-Mode, Synchronous Buck Controller With Power Good datasheet (Rev. H) May 23, 2019
Selection guide Power Management Guide 2018 (Rev. R) Jun. 25, 2018
Selection guide DC/DC Buck Controller Solutions Selection Guide Feb. 06, 2018
Application note Not All Jitter Is Created Equal (Rev. A) Jul. 04, 2015
Application note Enabling Multiple TPS4019x Devices Mar. 29, 2012
Application note 'C6472 12Vin Flexible Pwr Design Using DCDC Controllers and LDOs (8x C6472) Mar. 26, 2010
Application note Power Reference Design for the 'C6472, 12V DCDC Controllers, and LDOs Mar. 26, 2010
Application note TMS320C6472 5V Input Pwr Design, Integrated FET DC/DC Converters and Controllers Mar. 26, 2010
User guide Using the TPS40192EVM-525 Nov. 20, 2009
Application note 5Vin DM643x Power using DC/DC Controllers and LDO Oct. 09, 2008
User guide Using the TPS40192EVM-001 Jan. 29, 2007

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Design tools & simulation

SLIM025.ZIP (88 KB) - PSpice Model
SLVC169.ZIP (101 KB) - PSpice Model
SLVC170A.ZIP (12 KB) - TINA-TI Reference Design
SLVM012.ZIP (3 KB) - TINA-TI Spice Model
SLVM074.ZIP (95 KB) - TINA-TI Spice Model
PSpice® for TI design and simulation tool
PSPICE-FOR-TI — PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
  • Leverages Cadence PSpice Technology
  • Preinstalled library with a suite of digital models to enable worst-case timing analysis
  • Dynamic updates ensure you have access to most current device models
  • Optimized for simulation speed without loss of accuracy
  • Supports simultaneous analysis of multiple products
  • (...)
SLUC263D.ZIP (131 KB)

Reference designs

universal CURIE core supply
PMP4603 — core supply for TI DSP Curie
Design files
12V Input Sync Buck 0.9V@7A
PMP5752 — This reference design generates a 0.9V/7.5A output from a 12V input using the TPS40192 synchronous buck controller. The low Rds and fast switching of the CSD17313Q2 and CSD17308Q3 provide over 83% efficiency.
Synchronous buck converter 12V to 0.9V @7A
PMP5760 — This reference design generates a 0.9V/7.4A output from a 12V input using the TPS40192 synchronous buck controller. The low Rds and fast switching of the CSD86330Q3D provides over 86% efficiency.
Design files

CAD/CAE symbols

Package Pins Download
VSON (DRC) 10 View options

Ordering & quality

Information included:
  • RoHS
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​


Related videos