Product details


Output options Adjustable Output, Fixed Output Iout (Max) (A) 0.25 Vin (Max) (V) 10 Vin (Min) (V) 2.7 Vout (Max) (V) 5.5 Vout (Min) (V) 1.5 Fixed output options (V) 1.5, 1.6, 1.8, 2.8, 3.3, 5 Noise (uVrms) 55 Iq (Typ) (mA) 0.09 Thermal resistance θJA (°C/W) 243 Load capacitance (Min) (µF) 1 Rating Catalog Regulated outputs (#) 1 Features Enable, Power Good Accuracy (%) 2 PSRR @ 100 KHz (dB) 25 Dropout voltage (Vdo) (Typ) (mV) 200 Operating temperature range (C) -40 to 125 open-in-new Find other Linear regulators (LDO)

Package | Pins | Size

VSSOP (DGK) 8 15 mm² 3 x 4.9 open-in-new Find other Linear regulators (LDO)


  • Open Drain Power-On Reset With 220-ms Delay (TPS773xx)
  • Open Drain Power-Good (PG) Status Output (TPS774xx)
  • 250-mA Low-Dropout Voltage Regulator
  • Available in 1.5-V, 1.6-V (TPS77316 Only), 1.8-V, 2.7-V, 2.8-V, 3.3-V, 5.0-V Fixed Output and Adjustable Versions
  • Dropout Voltage Typically 200 mV at 250 mA (TPS77333, TPS77433)
  • Ultralow 92-uA Quiescent Current (Typ)
  • 8-Pin MSOP (DGK) Package
  • Low Noise (55 uVrms) Without an External Filter (Bypass) Capacitor (TPS77318, TPS77418)
  • 2% Tolerance Over Specified Conditions For Fixed-Output Versions
  • Fast Transient Response
  • Thermal Shutdown Protection
  • See the TPS779xx Family of Devices for Active High Enable

open-in-new Find other Linear regulators (LDO)


The TPS773xx and TPS774xx are low-dropout regulators with integrated power-on reset and power good (PG) function respectively. These devices are capable of supplying 250 mA of output current with a dropout of 200 mV (TPS77333, TPS77433). Quiescent current is 92 uA at full load dropping down to 1 uA when device is disabled. These devices are optimized to be stable with a wide range of output capacitors including low ESR ceramic (10 uF) or low capacitance (1 uF) tantalum capacitors. These devices have extremely low noise output performance (55 uVrms) without using any added filter capacitors. TPS773xx and TPS774xx are designed to have fast transient response for larger load current changes.

The TPS773xx or TPS774xx is offered in 1.5-V, 1.6 V (TPS77316 only), 1.8-V, 2.7-V, 2.8-V, 3.3-V, and 5.0-V fixed-voltage versions and in an adjustable version (programmable over the range of 1.5 V to 5.5 V). Output voltage tolerance is 2% over line, load, and temperature ranges. The TPS773xx and TPS774xx families are available in 8-pin MSOP (DGK) packages.

Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 200 mV at an output current of 250 mA for 3.3-volt option) and is directly proportional to the output current. Additionally, since the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (typically 92 uA over the full range of output current, 0 mA to 250 mA). These two key specifications yield a significant improvement in operating life for battery-powered systems.

The device is enabled when the EN\ pin is connected to a low-level input voltage. This LDO family also features a sleep mode; applying a TTL high signal to EN\ (enable) shuts down the regulator, reducing the quiescent current to less than 1 uA at T J = 25°C.

The TPS773xx features an integrated power-on reset, commonly used as a supply voltage supervisor (SVS), or reset output voltage. The RESET\ output of the TPS773xx initiates a reset in DSP, microcomputer or microprocessor systems at power up and in the event of an undervoltage condition. An internal comparator in the TPS773xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated output voltage. When OUT reaches 95% of its regulated voltage, RESET\ will go to a high-impedance state after a 220-ms delay. RESET\ will go to low-impedance state when OUT is pulled below 95% (i.e. over load condition) of its regulated voltage.

For the TPS774xx, the power good terminal (PG) is an active high output, which can be used to implement a power-on reset or a low-battery indicator. An internal comparator in the TPS774xx monitors the output voltage of the regulator to detect an undervoltage condition on the regulated output voltage. When OUT falls below 82% of its regulated voltage, PG will go to a low-impedance state. PG will go to a high-impedance state when OUT is above 82% of its regulated voltage.

open-in-new Find other Linear regulators (LDO)
Similar products you might be interested in
open-in-new Compare products
Similar but not functionally equivalent to the compared device:
TPS7A25 ACTIVE 300-mA, 18-V, ultra-low-IQ, high-accuracy, adjustable low-dropout voltage regulator with power good An 18-V, 300-mA LDO regulator with power-good and ultra-low IQ (2.5 μA)

Technical documentation

= Top documentation for this product selected by TI
No results found. Please clear your search and try again. View all 7
Type Title Date
* Datasheet 250-mA LDO Regulators With 8-pin MSOP Packaging datasheet (Rev. E) Mar. 22, 2002
Application notes LDO Noise Demystified (Rev. B) Aug. 18, 2020
Technical articles LDO basics: capacitor vs. capacitance Aug. 01, 2018
Technical articles LDO Basics: Preventing reverse current Jul. 25, 2018
Technical articles LDO basics: introduction to quiescent current Jun. 20, 2018
Application notes LDO PSRR Measurement Simplified (Rev. A) Aug. 09, 2017
Technical articles LDO basics: noise – part 1 Jun. 14, 2017

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Reference designs

RF430FRL152H NFC Temperature and Light Sensor Reference Design
TIDM-RF430FRLSENSE This reference design provides a platform to evaluate the RF430FRL152H NFC Sensor Interface Transponder.  Directly out of the box, thermistor and photo transistor measurements can be communicated to an NFC enabled smart phone or other NFC/RFID Reader device.  This reference design can be (...)
document-generic Schematic document-generic User guide
Software Controller Red/Green/Blue LED on Ultra Low Power Microcontroller
TIDM-G2XXSWRGBLED This reference design describes the implementation of a software controlled RGB LED on an MSP430, using a single timer module and Capture Compare Register.  This design also includes a serial communication interface for externally
document-generic Schematic document-generic User guide
Low-Power Sub-1 GHz Wireless Transceiver
TIDM-LPBP-WIRELESSNODE The Low-Power Sub-1 GHz Wireless Transceiver reference design enables a low cost bi-directional RF link (when using two transceivers). The on-board Anaren Integrated Radio (AIR) A110LR09A radio module with integrated antenna operates in the European 868-870MHz and US 902-928MHz ISM bands. The (...)
document-generic Schematic document-generic User guide
Camera Sensor Power (5V@ 0.150A)
PMP5308 This primary-side regulated, isolated flyback converter provides two independent 5V@150mA outputs. One output can be referenced to ground to make a negative output, allowing for a +/-5V split rail design.
Low Power Capacitive Touch Solution Human Machine Interface (HMI) Apps Reference Design
TIDM-LPBP-CAPTOUCH This TI Design demonstrates an ultra-low power implementation of capacitive touch inputs for various human machine interface (HMI) requirements in consumer, industrial & other applications. This solution leverages unique features available in the MSP430 Value Line microcontroller that enables (...)
document-generic Schematic document-generic User guide
SMBus Design Using Low Power Microcontroller
TIDM-SMBUS This design utilizes existing Launchpad evaluation kits and BoosterPack plug-in modules to demonstrate the implementation of a SMBus-based system using Texas Instrument’s MSP430 SMBus Library.
document-generic Schematic document-generic User guide
Near Field Communication (NFC) MIFARE DESFire EV1 Tag Authentication Reference Design
TIDM-NFC-DESFIRE-AES MIFARE DESFire EV1 is an ISO14443A RFID transponder and an NFC Type 4A Tag Platform that is used in many NFC and RFID security applications due to the ability it has to operate in the clear or operate as a secure transponder using AES Encryption. This design uses the TI AES library along with a (...)
document-generic Schematic
Low Power Orientation Tracker Reference Design
TIDM-ORIENTATIONTRACKER This reference application demonstrates how to combine an ultra-low-power MSP microcontroller, fixed-point software math libraries and an accelerometer for a low cost, ultra-low-power, simple orientation tracking solution. The MSP MCU samples the accelerometer and performs calculations in real time (...)
document-generic Schematic document-generic User guide

CAD/CAE symbols

Package Pins Download
VSSOP (DGK) 8 View options

Ordering & quality

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​


Related videos