TS3A226AE

ACTIVE

Audio jack switch with reduced GND switch Ron & FM capability

Top

Product details

Parameters

Protocols Analog Audio Configuration audio jack Number of channels (#) 1 VCC (Min) (V) 2.6 VCC (Max) (V) 4.7 Ron (Typ) (Ohms) 0.06 Input/ouput voltage (Min) (V) -2 Input/ouput voltage (Max) (V) 4.5 ICC (Max) (uA) 14 Bandwidth (MHz) 200 ESD HBM (Typ) (kV) 2 Operating temperature range (C) -40 to 85 ESD CDM (kV) 0.5 ICC (Typ) (uA) 6.5 Off isolation (Typ) (dB) -80 OFF-state leakage current (Max) (µA) 1 Ron (Max) (Ohms) 0.085 VIH (Min) (V) 1.48 VIL (Max) (V) 0.5 open-in-new Find other Protocol-specific switches/muxes

Package | Pins | Size

DSBGA (YFF) 9 2 mm² 1.396 x 1.296 open-in-new Find other Protocol-specific switches/muxes

Features

  • Ground FET Switches (60mΩ typical)
  • Autonomous Detection of Headset Types:
    3-Poles or 4-Poles (with MIC on SLEEVE or RING2)
  • Microphone Line Switches
  • Supports FM Signal Transmission Through the Ground FETs
  • Reduction of Click/Pop Noise
  • VDD Range: 2.6 V – 4.7 V
  • THD (Mic): 0.002% Typical
  • Low Current Consumption: 6.5-µA Typical
  • ±8kV Contract Discharge (IEC 61000-4-2) ESD Performance on SLEEVE and RING2 Pins
open-in-new Find other Protocol-specific switches/muxes

Description

The TS3A226AE is an audio headset switch that detects 3- or 4-pole 3.5mm accessories. For a 4-pole accessory with a microphone, the TS3A226AE also detects the MIC location and routes the microphone and ground signals automatically. The ground signal is routed through a pair of low-impedance ground FETs (60mΩ typical), resulting minimal impact on audio cross-talk performance. The autonomous detection feature allows end users to plug in accessories with different audio pole configurations into the mobile device and have them operate properly with no added software control and complexity. The ground FETs of the device are designed to allow FM signal pass-through, making it possible to use the ground line of the headset as an FM antenna in mobile audio application.

The TS3A226AE is packaged within a 1.2mm × 1.2mm WCSP package, making it suitable for use in mobile application.

open-in-new Find other Protocol-specific switches/muxes
Download

Technical documentation

= Featured
No results found. Please clear your search and try again. View all 10
Type Title Date
* Datasheet AUTONOMOUS AUDIO HEADSET SWITCH, TS3A226AE datasheet (Rev. A) Jul. 24, 2013
Technical articles Roll with the design punches and overcome power-sequencing challenges Jul. 29, 2019
Technical articles Is charge injection causing output voltage errors in your industrial control system? Oct. 18, 2018
Technical articles USB Type-C™ power: Should your next device have USB Type-C? Feb. 14, 2017
Technical articles USB Type-C audio: Do I need to buy a new pair of headphones? Jul. 07, 2016
Application notes Support Selfie Sticks Using a TS3A227E Audio Jack Switch Mar. 04, 2016
Selection guides Analog Switches Quick Select Guide Dec. 04, 2014
User guides TS3A226AE EVM Board User’s Guide (Rev. B) Aug. 13, 2013
Application notes Preventing Excess Power Consumption on Analog Switches Jul. 03, 2008
Application notes Semiconductor Packing Material Electrostatic Discharge (ESD) Protection Jul. 08, 2004

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

EVALUATION BOARDS Download
document-generic User guide
$99.00
Description

The TS3A226AEEVM is an evaluation module (EVM) for the Texas Instruments (TI) autonomous audio-headset switch. The EVM provides the basic functionality evaluation for theTS3A226AE device and provides peripheral connector for codec signal connection to MICP, TIP and RING1.

The TS3A226AE is an (...)

Features
  • Ground FET switches (60 mΩ typical)
  • Autonomous detection of headset types:
      3-Poles or 4-Poles (with MIC on SLEEVE or RING2)
  • Microphone line switches
  • Supports FM signal transmission through the ground FETs
  • Reduction of click and pop noise
  • VDD range: 2.6 V to 4.7 V
  • THD (MIC): 0.002% typical
  • Low current (...)

Design tools & simulation

SIMULATION MODELS Download
SCDM156.ZIP (476 KB) - HSpice Model

Reference designs

REFERENCE DESIGNS Download
USB Type-C™ Power-Path Protection With Audio Accessory Support Reference Design
TIDA-03030 — The TIDA-03030 reference design provides a robust protection solution for the power path in USB Type-C™ applications. The design protects the power path from overvoltage, overcurrent, hot-plug, and reverse-current events by leveraging the TPS25923 (eFuse) and CSD17571Q2 (reverse-blocking FET (...)
document-generic Schematic document-generic User guide
REFERENCE DESIGNS Download
Headset Detection Switch to Detect 3-Pole or 4-Pole 3.5mm Accessories
TIDA-00006 This reference design is for autonomous audio headset switch applications. Some audio headsets have integrated analog microphones. The GND and MIC connections on the audio jack connector may be swapped depending on the manufacturer. This design has the ability to detect the presence of an analog (...)
document-generic Schematic document-generic User guide

CAD/CAE symbols

Package Pins Download
DSBGA (YFF) 9 View options

Ordering & quality

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos

USB Redriver and Type-C Solutions

Learn about various USB Type-C design considerations.

Posted: 29-Jan-2019
Duration: 23:33

Related videos