首頁 邏輯元件和電壓轉換 電壓轉換器及電平移位器 電壓轉換器
首頁
邏輯元件和電壓轉換
電壓轉換器及電平移位器
電壓轉換器

SN74LVCH8T245

現行

具可配置電壓轉換和 3 態輸出的 8 位元雙電源匯流排收發器

立即訂購
產品規格表

SN74LVCH8T245

現行
產品規格表 立即訂購

產品詳細資料

Bits (#) 8 Data rate (max) (Mbps) 200 Topology Push-Pull Vout (min) (V) 1.65 Vout (max) (V) 5.5 Features Bus-hold, Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Prop delay (ns) 6.5 Technology family LVC Supply current (max) (mA) 0.025 Rating Catalog Operating temperature range (°C) -40 to 85
Bits (#) 8 Data rate (max) (Mbps) 200 Topology Push-Pull Vout (min) (V) 1.65 Vout (max) (V) 5.5 Features Bus-hold, Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Prop delay (ns) 6.5 Technology family LVC Supply current (max) (mA) 0.025 Rating Catalog Operating temperature range (°C) -40 to 85
SSOP (DB) 24 63.96 mm² 8.2 x 7.8 TSSOP (PW) 24 49.92 mm² 7.8 x 6.4 TVSOP (DGV) 24 32 mm² 5 x 6.4 VQFN (RHL) 24 19.25 mm² 5.5 x 3.5
  • Control inputs (DIR and OE) VIH and VIL levels are referenced to VCCA
  • Bus hold on data inputs eliminates the need for external pullup and pulldown resistors
  • VCC isolation
  • Fully configurable dual-rail design
  • Ioff supports Partial-Power-Down node operation
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD protection exceeds JESD 22
  • Control inputs (DIR and OE) VIH and VIL levels are referenced to VCCA
  • Bus hold on data inputs eliminates the need for external pullup and pulldown resistors
  • VCC isolation
  • Fully configurable dual-rail design
  • Ioff supports Partial-Power-Down node operation
  • Latch-up performance exceeds 100 mA per JESD 78, class II
  • ESD protection exceeds JESD 22

The SN74LVCH8T245 is an 8-bit noninverting bus transceiver that uses two separate configurable power-supply rails. The A port is designed to track VCCA, which accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB, which also accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5.5-V voltage nodes.

The SN74LVCH8T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs, the A-port outputs, or place both output ports into a high-impedance state. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports are always active.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device. The VCC isolation feature ensures that if either VCCA or VCCB is at GND, then the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCCA through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The SN74LVCH8T245 is designed so that the control pins (DIR and OE) are referenced to VCCA.

The SN74LVCH8T245 is an 8-bit noninverting bus transceiver that uses two separate configurable power-supply rails. The A port is designed to track VCCA, which accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB, which also accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5.5-V voltage nodes.

The SN74LVCH8T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs, the A-port outputs, or place both output ports into a high-impedance state. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports are always active.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device. The VCC isolation feature ensures that if either VCCA or VCCB is at GND, then the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCCA through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The SN74LVCH8T245 is designed so that the control pins (DIR and OE) are referenced to VCCA.
filter 尋找其它 電壓轉換器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 33
類型 標題 日期
* Data sheet SN74LVCH8T245 8-BIT Dual-Supply Bus Transceiver With Configurable Level-Shifting, Voltage Translation, and 3-State Outputs datasheet (Rev. C) PDF | HTML 2022年 12月 15日
Application note Schematic Checklist - A Guide to Designing With Fixed or Direction Control Translators PDF | HTML 2024年 10月 2日
Application note Schematic Checklist - A Guide to Designing with Auto-Bidirectional Translators PDF | HTML 2024年 7月 12日
Application note Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024年 7月 3日
Application note Implications of Slow or Floating CMOS Inputs (Rev. E) 2021年 7月 26日
Selection guide Voltage Translation Buying Guide (Rev. A) 2021年 4月 15日
Selection guide Little Logic Guide 2018 (Rev. G) 2018年 7月 6日
Selection guide Logic Guide (Rev. AB) 2017年 6月 12日
Application note How to Select Little Logic (Rev. A) 2016年 7月 26日
Application note Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) 2015年 12月 2日
Application note Designing with SN74LVCXT245 and SN74LVCHXT245 Family of Direction Controlled 2015年 10月 27日
User guide LOGIC Pocket Data Book (Rev. B) 2007年 1月 16日
Product overview Design Summary for WCSP Little Logic (Rev. B) 2004年 11月 4日
Application note Semiconductor Packing Material Electrostatic Discharge (ESD) Protection 2004年 7月 8日
Application note Selecting the Right Level Translation Solution (Rev. A) 2004年 6月 22日
User guide Signal Switch Data Book (Rev. A) 2003年 11月 14日
Application note Use of the CMOS Unbuffered Inverter in Oscillator Circuits 2003年 11月 6日
User guide LVC and LV Low-Voltage CMOS Logic Data Book (Rev. B) 2002年 12月 18日
Application note Texas Instruments Little Logic Application Report 2002年 11月 1日
Application note TI IBIS File Creation, Validation, and Distribution Processes 2002年 8月 29日
More literature Standard Linear & Logic for PCs, Servers & Motherboards 2002年 6月 13日
Application note 16-Bit Widebus Logic Families in 56-Ball, 0.65-mm Pitch Very Thin Fine-Pitch BGA (Rev. B) 2002年 5月 22日
Application note Power-Up 3-State (PU3S) Circuits in TI Standard Logic Devices 2002年 5月 10日
More literature STANDARD LINEAR AND LOGIC FOR DVD/VCD PLAYERS 2002年 3月 27日
Application note Migration From 3.3-V To 2.5-V Power Supplies For Logic Devices 1997年 12月 1日
Application note Bus-Interface Devices With Output-Damping Resistors Or Reduced-Drive Outputs (Rev. A) 1997年 8月 1日
Application note CMOS Power Consumption and CPD Calculation (Rev. B) 1997年 6月 1日
Application note LVC Characterization Information 1996年 12月 1日
Application note Input and Output Characteristics of Digital Integrated Circuits 1996年 10月 1日
Application note Live Insertion 1996年 10月 1日
Design guide Low-Voltage Logic (LVC) Designer's Guide 1996年 9月 1日
Application note Understanding Advanced Bus-Interface Products Design Guide 1996年 5月 1日
Selection guide Logic Guide (Rev. AC) PDF | HTML 1994年 6月 1日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

14-24-LOGIC-EVM — 適用於 14 針腳至 24 針腳 D、DB、DGV、DW、DYY、NS 和 PW 封裝的邏輯產品通用評估模組

14-24-LOGIC-EVM 評估模組 (EVM) 設計用於支援任何 14 針腳至 24 針腳 D、DW、DB、NS、PW、DYY 或 DGV 封裝的任何邏輯裝置。

使用指南: PDF | HTML
TI.com 無法提供
開發板

14-24-NL-LOGIC-EVM — 適用於 14 針腳至 24 針腳無引線封裝的邏輯產品通用評估模組

14-24-NL-LOGIC-EVM 是一款靈活的評估模組 (EVM)，設計用於支援任何具有 14 針腳至 24 針腳 BQA、BQB、RGY、RSV、RJW 或 RHL 封裝的邏輯或轉換裝置。

使用指南: PDF | HTML
TI.com 無法提供
開發板

AVCLVCDIRCNTRL-EVM — 適用於方向控制雙向轉換裝置、支援 AVC 和 LVC 的通用 EVM

通用 EVM 的設計可支援一、二、四、八通道 LVC 及 AVC 方向控制的轉換裝置。此外也支援相同通道數量的匯流排保留與汽車 -Q1 裝置。AVC 是低電壓轉換裝置，具較低驅動強度 12mA。LVC 是較高的電壓轉換裝置，範圍從 1.65 到 5.5V 且具較高驅動強度 32mA。

使用指南: PDF
TI.com 無法提供
模擬型號

SN74LVCH8T245 IBIS Model

SCEM493.ZIP (55 KB) - IBIS Model
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
SSOP (DB) 24 Ultra Librarian
TSSOP (PW) 24 Ultra Librarian
TVSOP (DGV) 24 Ultra Librarian
VQFN (RHL) 24 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片