SN74LVCR162245

現行

具有 3 態輸出的 16 位元匯流排收發器

立即訂購

產品規格表

document-pdfAcrobat SN74LVCR162245 datasheet (Rev. E) (英文)

SN74LVCR162245

現行

產品規格表

立即訂購

產品詳細資料

Number of channels

16

IOL (max) (mA)

12

IOH (max) (mA)

-12

Input type

TTL/CMOS

Output type

LVTTL

Features

Balanced outputs

Technology family

LVC

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Number of channels

16

IOL (max) (mA)

12

IOH (max) (mA)

-12

Input type

TTL/CMOS

Output type

LVTTL

Features

Balanced outputs

Technology family

LVC

Rating

Catalog

Operating temperature range (°C)

-40 to 85

SSOP (DL)

48

164.358 mm² (15.88 mm × 10.35 mm)

TSSOP (DGG)

48

101.25 mm² (12.5 mm × 8.1 mm)

Member of the Texas Instruments Widebus™ Family
Operates From 2.7 V to 3.6 V
Inputs Accept Voltages to 5.5 V
Max t_pd of 8.5 ns at 3.3 V
Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
Typical V_OHV (Output V_OH Undershoot)
>2 V at V_CC = 3.3 V, T_A = 25°C
Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
All Outputs Have Equivalent 26- Series Resistors, So No External Resistors Are Required
Latch-Up Performance Exceeds 250 mA Per JEDEC Standard JESD-17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

Widebus is a trademark of Texas Instruments.

Member of the Texas Instruments Widebus™ Family
Operates From 2.7 V to 3.6 V
Inputs Accept Voltages to 5.5 V
Max t_pd of 8.5 ns at 3.3 V
Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
Typical V_OHV (Output V_OH Undershoot)
>2 V at V_CC = 3.3 V, T_A = 25°C
Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
All Outputs Have Equivalent 26- Series Resistors, So No External Resistors Are Required
Latch-Up Performance Exceeds 250 mA Per JEDEC Standard JESD-17
ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)

Widebus is a trademark of Texas Instruments.

This 16-bit (dual-octal) noninverting bus transceiver is designed for 2.7-V to 3.6-V V_CC operation.

The SN74LVCR162245 is designed forasynchronous communication between data buses. The control-function implementation minimizes external timing requirements.

This device can be used as two 8-bit transceivers or one 16-bit transceiver. It allows data transmission from the A bus to the B bus or from the B bus to the A bus, depending upon the logic level at the direction-control (DIR) input. The output-enable (OE)\ input can be used to disable the device so that the buses are effectively isolated.

All outputs, which are designed to sink up to 12 mA, include 26- resistors to reduce overshoot and undershoot.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. The bus-hold circuitry is part of the input circuit and is not disabled by OE\ or DIR.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This 16-bit (dual-octal) noninverting bus transceiver is designed for 2.7-V to 3.6-V V_CC operation.

The SN74LVCR162245 is designed forasynchronous communication between data buses. The control-function implementation minimizes external timing requirements.

This device can be used as two 8-bit transceivers or one 16-bit transceiver. It allows data transmission from the A bus to the B bus or from the B bus to the A bus, depending upon the logic level at the direction-control (DIR) input. The output-enable (OE)\ input can be used to disable the device so that the buses are effectively isolated.

All outputs, which are designed to sink up to 12 mA, include 26- resistors to reduce overshoot and undershoot.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. The bus-hold circuitry is part of the input circuit and is not disabled by OE\ or DIR.

To ensure the high-impedance state during power up or power down, OE\ should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

filter

尋找其它通用收發器

下載觀看有字幕稿的影片影片