首頁 音訊 音訊放大器 喇叭放大器
首頁
音訊
音訊放大器
喇叭放大器
最新

TAS6754-Q1

現行

具 1L 調變的車用、19V、數位輸入四通道 D 類音訊放大器

立即訂購
產品規格表

TAS6754-Q1

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Digital Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 19 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 50 SNR (dB) 109 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 19 Sampling rate (max) (kHz) 192 Operating temperature range (°C) -40 to 125
Audio input type Digital Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 19 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 50 SNR (dB) 109 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 19 Sampling rate (max) (kHz) 192 Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² 18.42 x 10.35
  • AEC-Q100 qualified for Automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5V to 19V supply voltage, 40V load dump
    • Low latency path reducing group delay by >70% at 48kHz
    • Support for 1.8V and 3.3V I/O’s
    • I2C control with 8 address options
  • 1L Modulation
    • Requires only one inductor per channel saving four inductors vs a traditional design
    • Lower system component cost for inductors
    • Smaller PCB footprint
  • Audio Performance
    • THD+N 0.03% (4Ω, 1W, 1kHz)
    • Output noise: 35µVRMS at 14.4V, A-weighting
    • Efficiency > 87% @ 4×25W, 4Ω, 14.4V
  • Output current sensing by channel via I2S or TDM
    • No external circuitry needed
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open load and shorted load detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel via I2S or 4-16 channel via TDM
    • Input sample rates: 44.1, 48, 96, 192kHz
  • Audio outputs
    • 4 channel bridge-tied load (BTL)
    • 2MHz output switching frequency
    • 4×30W (4Ω, 14.4V, 1kHz, 10% THD+N)
    • 4×50W (2Ω, 14.4V, 1kHz, 10% THD+N)
  • Advanced spread-spectrum and selectable phase offset
  • Protection and Monitoring
    • Cycle-by-cycle current limiting
    • Output short protection
    • Clip detection with configurable thresholds
    • Thermal foldback and PVDD foldback
    • I2C temperature and supply voltage readout
    • Configurable overtemperature warning and individual channel shutdown
    • DC offset, undervoltage and overvoltage
  • AEC-Q100 qualified for Automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5V to 19V supply voltage, 40V load dump
    • Low latency path reducing group delay by >70% at 48kHz
    • Support for 1.8V and 3.3V I/O’s
    • I2C control with 8 address options
  • 1L Modulation
    • Requires only one inductor per channel saving four inductors vs a traditional design
    • Lower system component cost for inductors
    • Smaller PCB footprint
  • Audio Performance
    • THD+N 0.03% (4Ω, 1W, 1kHz)
    • Output noise: 35µVRMS at 14.4V, A-weighting
    • Efficiency > 87% @ 4×25W, 4Ω, 14.4V
  • Output current sensing by channel via I2S or TDM
    • No external circuitry needed
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open load and shorted load detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel via I2S or 4-16 channel via TDM
    • Input sample rates: 44.1, 48, 96, 192kHz
  • Audio outputs
    • 4 channel bridge-tied load (BTL)
    • 2MHz output switching frequency
    • 4×30W (4Ω, 14.4V, 1kHz, 10% THD+N)
    • 4×50W (2Ω, 14.4V, 1kHz, 10% THD+N)
  • Advanced spread-spectrum and selectable phase offset
  • Protection and Monitoring
    • Cycle-by-cycle current limiting
    • Output short protection
    • Clip detection with configurable thresholds
    • Thermal foldback and PVDD foldback
    • I2C temperature and supply voltage readout
    • Configurable overtemperature warning and individual channel shutdown
    • DC offset, undervoltage and overvoltage

The TAS6754-Q1 is a four-channel digital-input Class-D audio amplifier that implements 1L modulation only requiring one inductor per BTL channel reducing system size and cost by removing four inductors compared to a traditional design. Additionally, 1L modulation lowers switching losses compared to traditional Class-D modulation schemes.

The TAS6754-Q1 integrates DC and AC Load Diagnostics to determine the status of the connected loads. During audio playback this status can be monitored through output current sense which is available for each channel and reports the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio through real-time load diagnostics independent of the host and audio input.

The TAS6754-Q1 device features an additional low latency signal path for each channel, providing up to 70% faster signal processing at 48kHz which enables time-sensitive Active Noise Cancellation (ANC), Road Noise Cancellation (RNC) applications.

The device supports global temperature, channel temperature and PVDD values via I2C readout for easy system level thermal management.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.

The TAS6754-Q1 is a four-channel digital-input Class-D audio amplifier that implements 1L modulation only requiring one inductor per BTL channel reducing system size and cost by removing four inductors compared to a traditional design. Additionally, 1L modulation lowers switching losses compared to traditional Class-D modulation schemes.

The TAS6754-Q1 integrates DC and AC Load Diagnostics to determine the status of the connected loads. During audio playback this status can be monitored through output current sense which is available for each channel and reports the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio through real-time load diagnostics independent of the host and audio input.

The TAS6754-Q1 device features an additional low latency signal path for each channel, providing up to 70% faster signal processing at 48kHz which enables time-sensitive Active Noise Cancellation (ANC), Road Noise Cancellation (RNC) applications.

The device supports global temperature, channel temperature and PVDD values via I2C readout for easy system level thermal management.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.
filter 尋找其它 喇叭放大器
下載 觀看有字幕稿的影片 影片
索取更多資訊

提供其他設計資源。立即索取

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet TAS6754-Q1 ​​​1L Modulation, 2MHz Digital Input 4-Channel Automotive Class-D Audio Amplifier with Current Sense and Real-time Load Diagnostics datasheet (Rev. A) PDF | HTML 2025年 3月 17日
Technical article 利用 D 類放大器 1L 調變技術，縮減汽車音訊系統設計尺寸 PDF | HTML 2024年 12月 31日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TAS6754Q1EVM — TAS6754-Q1 評估模組

TAS6754-Q1 評估模組 (EVM) 展示了 TAS6754-Q1，這是一款具有 1L 調變功能的車用四通道數位輸入閉合迴路 D 類音訊放大器，可在每通道減少 1 個電感器，並可為四通道減少 50% 的電感器成本。TAS6754-Q1 具備整合式 DSP，可支援許多功能，例如即時負載診斷、電流感測、適用 ANC/RNC 的選用低延遲音訊路徑，以及 PVDD 和熱增益折返等進階保護功能。EVM 在編程和 I2C 配置中使用 PurePathTM Console (PPC3) 圖形使用者介面 (GUI)，以評估 TAS6754-Q1 裝置的特性、功能和性能。
要求
應用軟體及架構

PUREPATHCONSOLE — 適用於音訊系統設計和開發的 PurePath™ Console 圖形開發套件

PurePath™ Console 是一款高度整合且容易使用的音訊開發套件，專爲簡化音訊產品開發相關評估、配置和偵錯程序所設計。瞭解使用 PurePath™ Console 3 軟體有多簡單。
PurePath Console 的直覺式圖形介面無需進階音訊工程專業，因此讓音訊設計更加簡明直觀。在簡單易用的圖形介面中，實作 PurePath Console 的眾多進階控制功能，並以縮短產品開發時間為目標，為您實現高度最佳化的音訊性能、最低功耗和順暢系統整合。

支援的裝置：

PurePath™ Console 1：PCM5142、TAS5721、TAS5729MD、TAS5731 和 (...)
View Options
支援軟體

TAS6754-Q1-DESIGN — TAS6754-Q1 Technical Documentation

TAS6754-Q1 Technical Documentation
支援產品和硬體

支援產品和硬體

產品
喇叭放大器
TAS6754-Q1 — 具 1L 調變的車用、19V、數位輸入四通道 D 類音訊放大器
硬體開發
開發板
TAS6754Q1EVM — TAS6754-Q1 評估模組
要求
支援軟體

TAS6754-Q1-SW — TAS6754-Q1 PPC3 GUI

TAS6754-Q1 PPC3 GUI
支援產品和硬體

支援產品和硬體

產品
喇叭放大器
TAS6754-Q1 — 具 1L 調變的車用、19V、數位輸入四通道 D 類音訊放大器
硬體開發
開發板
TAS6754Q1EVM — TAS6754-Q1 評估模組
要求
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HSSOP (DKQ) 56 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片