SBOS531E August   2010  – June 2019 AFE031

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1.     Device Images
  4. 4 Revision History
  5. 5 Description, continued
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
    1.     Pin Functions
  8. 8 Specifications
    1. 8.1  Absolute Maximum Ratings
    2. 8.2  ESD Ratings
    3. 8.3  Thermal Information
    4. 8.4  Electrical Characteristics: Transmitter (Tx)
    5. 8.5  Electrical Characteristics: Power Amplifier (PA)
    6. 8.6  Electrical Characteristics: Receiver (Rx)
    7. 8.7  Electrical Characteristics: Digital
    8. 8.8  Electrical Characteristics: Two-Wire Interface
    9. 8.9  Electrical Characteristics: Internal Bias Generator
    10. 8.10 Electrical Characteristics: Power Supply
    11. 8.11 Timing Requirements
    12. 8.12 Timing Diagrams
    13. 8.13 Typical Characteristics
  9. 9 Detailed Description
    1. 9.1 Functional Block Diagram
    2. 9.2 Feature Description
      1. 9.2.1 PA Block
      2. 9.2.2 Tx Block
      3. 9.2.3 Rx Block
      4. 9.2.4 DAC Block
      5. 9.2.5 REF1 and REF2 Blocks
      6. 9.2.6 Zero Crossing Detector Block
      7. 9.2.7 ETx and ERx Blocks
    3. 9.3 Power Supplies
    4. 9.4 Pin Descriptions
      1. 9.4.1 Current Overload
      2. 9.4.2 Thermal Overload
    5. 9.5 Calibration Modes
      1. 9.5.1 Tx Calibration Mode
      2. 9.5.2 Rx Calibration Mode
    6. 9.6 Serial Interface
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Detailed Design Procedure
        1. 10.2.1.1 Line-Coupling Circuit
        2. 10.2.1.2 Circuit Protection
        3. 10.2.1.3 Thermal Considerations
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 Development Support
        1. 11.1.2.1 Powerline Communications Developer’s Kit
        2. 11.1.2.2 TINA-TI™ (Free Software Download)
        3. 11.1.2.3 TI Precision Designs
        4. 11.1.2.4 WEBENCH Filter Designer
    2. 11.2 Documentation Support
      1. 11.2.1 Related Documentation
    3. 11.3 Receiving Notification of Documentation Updates
    4. 11.4 Community Resources
    5. 11.5 Trademarks
    6. 11.6 Electrostatic Discharge Caution
    7. 11.7 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.8 Electrical Characteristics: Two-Wire Interface

At TJ = 25°C, PA_VS = 16 V, VAVDD = VDVDD = 3.3 V, and 10 kΩ connected to PA_ISET (pin 46), unless otherwise noted.
PARAMETER CONDITIONS MIN TYP MAX UNIT
TWO-WIRE TRANSMITTER
Frequency range(1) 50 kHz
Leakage input current
(E_Tx_In, E_Tx_Clk)		 0 ≤ VIN ≤ DVDD –1 0.01 1 μA
Input logic levels (E_Tx_In, E_Tx_Clk)
VIH High-level input voltage 0.7 • DVDD V
VIL Low-level input voltage 0.3 • DVDD V
Output logic levels (E_Tx_Out)
VOH High-level output voltage IOH = 3 mA AVDD – 0.4 AVDD V
VOL Low-level output voltage IOL = –3 mA GND GND + 0.4 V
TWO-WIRE RECEIVER
Gain –4.5 dB
Frequency range 300 kHz
Max sink current 25 mA
Max source current 25 mA
Input terminal offset Referenced to VAVDD/2 –100 10 100 mV
Input impedance 78 kΩ
ZERO CROSSING DETECTOR
Input voltage range AVDD – 0.4 AVDD + 0.4 V
Input current range –10 10 mA
Input capacitance 3 pF
Rising threshold 0.45 0.9 1.35 V
Falling threshold 0.25 0.5 0.75 V
Hysteresis 0.20 0.4 0.60 V
Jitter 50 Hz, 240 VRMS 10 ns
(1) The two-wire transmitter circuit is tested at Tx_CLK = 10 MHz.