SLASFB2 November   2023 AFE432A3W , AFE532A3W

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Voltage Output
    6. 5.6  Electrical Characteristics: Current Output
    7. 5.7  Electrical Characteristics: Comparator Mode
    8. 5.8  Electrical Characteristics: ADC Input
    9. 5.9  Electrical Characteristics: General
    10. 5.10 Timing Requirements: I2C Standard Mode
    11. 5.11 Timing Requirements: I2C Fast Mode
    12. 5.12 Timing Requirements: I2C Fast-Mode Plus
    13. 5.13 Timing Requirements: SPI Write Operation
    14. 5.14 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 0)
    15. 5.15 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 1)
    16. 5.16 Timing Requirements: GPIO
    17. 5.17 Timing Diagrams
    18. 5.18 Typical Characteristics: Voltage Output
    19. 5.19 Typical Characteristics: Current Output
    20. 5.20 Typical Characteristics: Comparator
    21. 5.21 Typical Characteristics: ADC
    22. 5.22 Typical Characteristics: General
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Smart Analog Front End (AFE) Architecture
      2. 6.3.2 Digital Input/Output
      3. 6.3.3 Nonvolatile Memory (NVM)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Voltage-Output Mode
        1. 6.4.1.1 Voltage Reference and DAC Transfer Function
          1. 6.4.1.1.1 Internal Reference
          2. 6.4.1.1.2 Power-Supply as Reference
      2. 6.4.2 Current-Output Mode
      3. 6.4.3 Comparator Mode
        1. 6.4.3.1 Programmable Hysteresis Comparator
        2. 6.4.3.2 Programmable Window Comparator
      4. 6.4.4 Analog-to-Digital Converter (ADC) Mode
      5. 6.4.5 Fault-Dump Mode
      6. 6.4.6 Application-Specific Modes
        1. 6.4.6.1 Voltage Margining and Scaling
          1. 6.4.6.1.1 High-Impedance Output and PROTECT Input
          2. 6.4.6.1.2 Programmable Slew-Rate Control
        2. 6.4.6.2 Function Generation
          1. 6.4.6.2.1 Triangular Waveform Generation
          2. 6.4.6.2.2 Sawtooth Waveform Generation
          3. 6.4.6.2.3 Sine Waveform Generation
      7. 6.4.7 Device Reset and Fault Management
        1. 6.4.7.1 Power-On Reset (POR)
        2. 6.4.7.2 External Reset
        3. 6.4.7.3 Register-Map Lock
        4. 6.4.7.4 NVM Cyclic Redundancy Check (CRC)
          1. 6.4.7.4.1 NVM-CRC-FAIL-USER Bit
          2. 6.4.7.4.2 NVM-CRC-FAIL-INT Bit
      8. 6.4.8 General-Purpose Input/Output (GPIO) Modes
    5. 6.5 Programming
      1. 6.5.1 SPI Programming Mode
      2. 6.5.2 I2C Programming Mode
        1. 6.5.2.1 F/S Mode Protocol
        2. 6.5.2.2 I2C Update Sequence
          1. 6.5.2.2.1 Address Byte
          2. 6.5.2.2.2 Command Byte
        3. 6.5.2.3 I2C Read Sequence
  8. 7 Register Map
    1. 7.1  NOP Register (address = 00h) [reset = 0000h]
    2. 7.2  DAC-0-MARGIN-HIGH Register (address = 0Dh) [reset = 0000h]
    3. 7.3  DAC-1-MARGIN-HIGH Register (address = 13h) [reset = 0000h]
    4. 7.4  DAC-2-MARGIN-HIGH Register (address = 01h) [reset = 0000h]
    5. 7.5  DAC-0-MARGIN-LOW Register (address = 0Eh) [reset = 0000h]
    6. 7.6  DAC-1-MARGIN-LOW Register (address = 14h) [reset = 0000h]
    7. 7.7  DAC-2-MARGIN-LOW Register (address = 02h) [reset = 0000h]
    8. 7.8  DAC-0-GAIN-CONFIG Register (address = 0Fh) [reset = 0000h]
    9. 7.9  DAC-1-GAIN-CMP-CONFIG Register (address = 15h) [reset = 0000h]
    10. 7.10 DAC-2-GAIN-CONFIG Register (address = 03h) [reset = 0000h]
    11. 7.11 DAC-1-CMP-MODE-CONFIG Register (address = 17h) [reset = 0000h]
    12. 7.12 DAC-0-FUNC-CONFIG Register (address = 12h) [reset = 0000h]
    13. 7.13 DAC-1-FUNC-CONFIG Register (address = 18h) [reset = 0000h]
    14. 7.14 DAC-2-FUNC-CONFIG Register (address = 06h) [reset = 0000h]
    15. 7.15 DAC-0-DATA Register (address = 1Bh) [reset = 0000h]
    16. 7.16 DAC-1-DATA Register (address = 1Ch) [reset = 0000h]
    17. 7.17 DAC-2-DATA Register (address = 19h) [reset = 0000h]
    18. 7.18 ADC-CONFIG-TRIG Register (address = 1Dh) [reset = 0000h]
    19. 7.19 ADC-DATA Register (address = 1Eh) [reset = 0001h]
    20. 7.20 COMMON-CONFIG Register (address = 1Fh) [reset = 0FFFh]
    21. 7.21 COMMON-TRIGGER Register (address = 20h) [reset = 0000h]
    22. 7.22 COMMON-DAC-TRIG Register (address = 21h) [reset = 0000h]
    23. 7.23 GENERAL-STATUS Register (address = 22h) [reset = 20h, DEVICE-ID, VERSION-ID]
    24. 7.24 CMP-STATUS Register (address = 23h) [reset = 000Ch]
    25. 7.25 GPIO-CONFIG Register (address = 24h) [reset = 0000h]
    26. 7.26 DEVICE-MODE-CONFIG Register (address = 25h) [reset = 0000h]
    27. 7.27 INTERFACE-CONFIG Register (address = 26h) [reset = 0000h]
    28. 7.28 SRAM-CONFIG Register (address = 2Bh) [reset = 0000h]
    29. 7.29 SRAM-DATA Register (address = 2Ch) [reset = 0000h]
    30. 7.30 BRDCAST-DATA Register (address = 50h) [reset = 0000h]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • YBH|16
Thermal pad, mechanical data (Package|Pins)
Orderable Information
6.4.6.1.2 Programmable Slew-Rate Control

When the DAC data registers are written, the voltage (VOUTX) or current (IOUT) on DAC output immediately transitions to the new code following the slew rate and settling time specified in the Electrical Characteristics.

The slew rate control feature allows the user to control the rate at which the output voltage (VOUT) changes. When this feature is enabled (using the SLEW-RATE-x[3:0] bits), the DAC output changes from the current code to the code in the DAC-x-MARGIN-HIGH or DAC-x-MARGIN-LOW registers (when margin high or low commands are issued to the DAC) using the step size and time-period per step set in CODE-STEP-x and SLEW-RATE-x bits in the DAC-x-FUNC-CONFIG register:

  • SLEW-RATE-x defines the time-period per step at which the digital slew updates.
  • CODE-STEP-x defines the number of LSBs by which the output value changes at each update, for the corresponding channels.

Table 6-6 and Table 6-7 show different settings available for CODE-STEP-x and SLEW-RATE-x. With the default slew rate control setting of no-slew, the output changes immediately at a rate limited by the output drive circuitry and the attached load.

When the slew rate control feature is used, the output changes happen at the programmed slew rate. Figure 6-10 shows that this configuration results in a staircase formation at the output. Do not write to CODE-STEP-x, SLEW-RATE-x, or DAC-x-DATA during the output slew operation. Equation 5 provides the equation for the calculating the slew time (tSLEW).

GUID-902C2252-5E64-4109-A2C2-B55E2FC9D79E-low.svgFigure 6-10 Programmable Slew-Rate Control
Equation 5. tSLEW=SLEW_RATE×CEILINGMARGIN_HIGH-MARGIN_LOWCODE_STEP+1

where:

  • SLEW_RATE is the SLEW-RATE-x setting specified in Table 6-7.
  • CODE_STEP is the CODE-STEP-x setting specified in Table 6-6.
  • MARGIN_HIGH is the decimal value of the DAC-x-MARGIN-HIGH bits in the DAC-x-MARGIN-HIGH register.
  • MARGIN_LOW is the decimal value of the DAC-x-MARGIN-LOW bits in the DAC-x-MARGIN-LOW register.
Table 6-6 Code Step
REGISTER CODE-STEP-x[2]CODE-STEP-x[1]CODE-STEP-x[0]CODE STEP SIZE
DAC-x-FUNC-CONFIG0001 LSB (default)
0012 LSB
0103 LSB
0114 LSB
1006 LSB
1018 LSB
11016 LSB
11132 LSB
Table 6-7 Slew Rate
REGISTERSLEW-RATE-x[3]SLEW-RATE-x[2]SLEW-RATE-x[1]SLEW-RATE-x[0]TIME PERIOD
(PER STEP)
DAC-x-FUNC-CONFIG0000No slew (default)
00014 µs
00108 µs
001112 µs
010018 µs
010127 µs
011040.5 µs
011160.75 µs
100091.13 µs
1001136.69 µs
1010239.2 µs
1011418.61 µs
1100732.56 µs
11011281.98 µs
11102563.96 µs
11115127.92 µs