SLUSCS3J October   2017  – December 2022 BQ2980 , BQ2982

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Device Configurability
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Overvoltage (OV) Status
      2. 8.3.2 Undervoltage (UV) Status
      3. 8.3.3 Overcurrent in Charge (OCC) Status
      4. 8.3.4 Overcurrent in Discharge (OCD) and Short Circuit in Discharge (SCD) Status
      5. 8.3.5 Overtemperature (OT) Status
      6. 8.3.6 Charge and Discharge Driver
      7. 8.3.7 CTR for FET Override and Device Shutdown
      8. 8.3.8 CTR for PTC Connection
      9. 8.3.9 ZVCHG (0-V Charging)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power Modes
        1. 8.4.1.1 Power-On-Reset (POR)
        2. 8.4.1.2 NORMAL Mode
        3. 8.4.1.3 FAULT Mode
        4. 8.4.1.4 SHUTDOWN Mode
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Test Circuits for Device Evaluation
      2. 9.1.2 Test Circuit Diagrams
      3. 9.1.3 Using CTR as FET Driver On/Off Control
    2. 9.2 Typical Applications
      1. 9.2.1 BQ298x Configuration 1: System-Controlled Reset/Shutdown Function
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Selection of Power FET
        4. 9.2.1.4 Application Curves
      2. 9.2.2 BQ298x Configuration 2: CTR Function Disabled
      3. 9.2.3 BQ298x Configuration 3: PTC Thermistor Protection
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Third-Party Products Disclaimer
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

8.4.1.4 SHUTDOWN Mode

This mode is the lowest power-consumption state of the device, with both CHG and DSG turned off.

The two conditions to enter SHUTDOWN mode are as follows:

  • Undervoltage (UV): If the device is configured with UV_SHUT enabled, when UV protection is triggered, the device enters SHUTDOWN mode. See Section 8.3.2 for details.
  • CTR control: When CTR is HIGH for > 5.4 s, the device enters SHUTDOWN mode. See Section 8.3.7 for details.

Note:

If the internal CTR pull-up is enabled, a HIGH at CTR does not activate the shutdown process. This is because when the internal pull-up is enabled, the CTR pin is configured for use with an external PTC for overtemperature protection, and the CTR functionality is disabled.