SLLS897F march   2008  – august 2023 ISO1176

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Ratings
    6. 6.6  Insulation Specifications
    7. 6.7  Safety-Related Certifications
    8. 6.8  Safety Limiting Values
    9. 6.9  Electrical Characteristics: Driver
    10. 6.10 Electrical Characteristics: Receiver
    11. 6.11 Supply Current
    12. 6.12 Electrical Characteristics: ISODE-Pin
    13. 6.13 Switching Characteristics: Driver
    14. 6.14 Switching Characteristics: Receiver
    15. 6.15 Insulation Characteristics Curves
    16. 6.16 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Device Functional Modes
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Transient Voltages
        2. 9.2.2.2 ISO1176 “Sticky Bit” Issue (Under Certain Conditions)
      3. 9.2.3 Application Curve
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  13. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Support Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.9 Electrical Characteristics: Driver

All typical specs are at VCC1=3.3V, VCC2=5V, TA=27°C, (Min/Max specs are over recommended operating conditions unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
|VOD| Open-circuit differential output voltage
|VA-VB|, Figure 8
 		 1.8 VCC2 V
|VOD(SS)| Steady state differential output voltage magnitude  See Figure 9 and Figure 13
 		 2.1 V
Steady state differential output voltage magnitude  Common mode loading with Vtest from -7V to 12V, See figure 10
 		 2.1 V
Δ|VODSS| Change in differential output voltage between two states
RL = 54 ohms, See Figure 11 and Figure 12
 		 –200 200 mV
VOC(SS) Steady state common-mode output voltage
RL = 54 ohms, See Figure 11 and Figure 12
 		 2 3 V
ΔVOC(SS) change in steady-state common-mode output voltage between two states
RL = 54 ohms, See Figure 11 and Figure 12
 		 –200 200 mV
VOC(PP) Peak-to-peak common-mode output voltage
RL = 54 ohms, See Figure 11 and Figure 12
 		 0.5 V
VOD(RING) Differential output voltage over and undershoot See Figure 13 and Figure 17 10 %VOD(PP)
VI(HYS) Input voltage hysteresis See Figure 14 150 mV
II Input current
D, DE at 0 V or VCC1
 		 –10 10 µA

PV(1) at 0 V or VCC1
 		 120 µA
IO(OFF) Output current with power off Vcc ≤ 2.5V See receiver input
current in Electrical Characteristics:
Receiver
IOZ High-impedance state output current DE at 0 V
IOS(P) Peak short circuit output current DE at VCC, See Figure 15 and Figure 16: VOS = -7 to 12 V –250 250 mA
IOS(SS) Steady state short-circuit output current DE at VCC, See Figure 15 and Figure 16: VOS = 12 V, D at GND1 150 mA
DE at VCC, See Figure 15 and Figure 16: VOS = -7 V, D at VCC1 –150 mA
COD
Differential output capacitance

 7 10 pF
CMTI Common-mode transient immunity
See Figure 27
 		 25 kV/µs
(1) The PV pin has a 50-kΩ pullup resistor and leakage current depends on supply voltage.