SWRS289 october   2021 IWR2243

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Functional Block Diagram
  6. 5 Revision History
  7. 6 Device Comparison
    1. 6.1 Related Products
  8. 7 Terminal Configuration and Functions
    1. 7.1 Pin Diagram
    2. 7.2 Signal Descriptions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Power-On Hours (POH)
    4. 8.4 Recommended Operating Conditions
    5. 8.5 Power Supply Specifications
    6. 8.6 Power Consumption Summary
    7. 8.7 RF Specification
    8. 8.8 Thermal Resistance Characteristics for FCBGA Package [ABL0161]
    9. 8.9 Timing and Switching Characteristics
      1. 8.9.1 Power Supply Sequencing and Reset Timing
      2. 8.9.2 Synchronized Frame Triggering
      3. 8.9.3 Input Clocks and Oscillators
        1. 8.9.3.1 Clock Specifications
      4. 8.9.4 Multibuffered / Standard Serial Peripheral Interface (MibSPI)
        1. 8.9.4.1 Peripheral Description
          1. 8.9.4.1.1 SPI Timing Conditions
          2. 8.9.4.1.2 SPI Peripheral Mode Switching Parameters (SPICLK = input, SPISIMO = input, and SPISOMI = output)
          3. 8.9.4.1.3 SPI Peripheral Mode Timing Requirements (SPICLK = input, SPISIMO = input, and SPISOMI = output)
        2. 8.9.4.2 Typical Interface Protocol Diagram (Peripheral Mode)
      5. 8.9.5 Inter-Integrated Circuit Interface (I2C)
        1. 8.9.5.1 I2C Timing Requirements
      6. 8.9.6 Quad Serial Peripheral Interface (QSPI)
        1. 8.9.6.1 QSPI Timing Conditions
        2. 8.9.6.2 Timing Requirements for QSPI Input (Read) Timings
        3. 8.9.6.3 QSPI Switching Characteristics
      7. 8.9.7 LVDS Interface Configuration
        1. 8.9.7.1 LVDS Interface Timings
      8. 8.9.8 General-Purpose Input/Output
        1. 8.9.8.1 Switching Characteristics for Output Timing versus Load Capacitance (CL)
      9. 8.9.9 Camera Serial Interface (CSI)
        1. 8.9.9.1 CSI Switching Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Subsystems
      1. 9.3.1 RF and Analog Subsystem
        1. 9.3.1.1 Clock Subsystem
        2. 9.3.1.2 Transmit Subsystem
        3. 9.3.1.3 Receive Subsystem
      2. 9.3.2 Host Interface
    4. 9.4 Other Subsystems
      1. 9.4.1 ADC Data Format Over CSI2 Interface
      2. 9.4.2 ADC Channels (Service) for User Application
        1. 9.4.2.1 GPADC Parameters
  11. 10Monitoring and Diagnostic Mechanisms
  12. 11Applications, Implementation, and Layout
    1. 11.1 Application Information
    2. 11.2 Imaging Radar using Cascade Configuration
    3. 11.3 Reference Schematic
    4. 11.4 Layout
      1. 11.4.1 Layout Guidelines
      2. 11.4.2 Stackup Details
  13. 12Device and Documentation Support
    1. 12.1 Device Nomenclature
    2. 12.2 Tools and Software
    3. 12.3 Documentation Support
    4. 12.4 Support Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Export Control Notice
    8. 12.8 Glossary
  14. 13Mechanical, Packaging, and Orderable Information
    1. 13.1 Packaging Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.4.1 ADC Data Format Over CSI2 Interface

The IWR2243 device uses MIPI D-PHY / CSI2-based format to transfer the raw ADC samples to the external MCU. This is shown in Figure 9-4.

  • Supports four data lanes
  • CSI-2 data rate scalable from 150 Mbps to 600 Mbps per lane
  • Virtual channel based
  • CRC generation
GUID-3109FBD5-5B9A-4A55-8874-52DB70362B60-low.gif
Frame Start – CSi2 VSYNC Start Short Packet
Line Start – CSI2 HSYNC Start Short Packet
Line End – CSI2 HSYNC End Short Packet
Frame End – CSi2 VSYNC End Short Packet
Figure 9-4 CSI-2 Transmission Format

The data payload is constructed with the following three types of information:

  • Chirp profile information
  • The actual chirp number
  • ADC data corresponding to chirps of all four channels
    • Interleaved fashion
  • Chirp quality data (configurable)

The payload is then split across the four physical data lanes and transmitted to the receiving D-PHY. The data packet packing format is shown in Figure 9-5

GUID-3B89FBD5-0F78-4D23-8862-0CE2B3289F42-low.gifFigure 9-5 Data Packet Packing Format for 12-Bit Complex Configuration