SLVSF02E march   2019  – may 2023 TPS23881

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Detailed Pin Description
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Parameter Measurement Information
    1. 8.1 Timing Diagrams
  10. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1 Operating Modes
        1. 9.1.1.1 Auto
        2. 9.1.1.2 Semiauto
        3. 9.1.1.3 Manual and Diagnostic
        4. 9.1.1.4 Power Off
      2. 9.1.2 PoE Compliance Terminology
      3. 9.1.3 Channel versus Port Terminology
      4. 9.1.4 Requested Class versus Assigned Class
      5. 9.1.5 Power Allocation and Power Demotion
      6. 9.1.6 Programmable SRAM
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Port Remapping
      2. 9.3.2 Port Power Priority
      3. 9.3.3 Analog-to-Digital Converters (ADC)
      4. 9.3.4 I2C Watchdog
      5. 9.3.5 Current Foldback Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Detection
      2. 9.4.2 Connection Check
      3. 9.4.3 Classification
      4. 9.4.4 DC Disconnect
    5. 9.5 I2C Programming
      1. 9.5.1 I2C Serial Interface
    6. 9.6 Register Maps
      1. 9.6.1 Complete Register Set
      2. 9.6.2 Detailed Register Descriptions
        1. 9.6.2.1  INTERRUPT Register
        2. 9.6.2.2  INTERRUPT MASK Register
        3. 9.6.2.3  POWER EVENT Register
        4. 9.6.2.4  DETECTION EVENT Register
        5. 9.6.2.5  FAULT EVENT Register
        6. 9.6.2.6  START/ILIM EVENT Register
        7. 9.6.2.7  SUPPLY and FAULT EVENT Register
          1. 9.6.2.7.1 Detected SRAM Faults and "Safe Mode"
            1. 9.6.2.7.1.1 ULA (Ultra Low Alpha) Package Option: TPS23881A
        8. 9.6.2.8  CHANNEL 1 DISCOVERY Register
        9. 9.6.2.9  CHANNEL 2 DISCOVERY Register
        10. 9.6.2.10 CHANNEL 3 DISCOVERY Register
        11. 9.6.2.11 CHANNEL 4 DISCOVERY Register
        12. 9.6.2.12 POWER STATUS Register
        13. 9.6.2.13 PIN STATUS Register
        14. 9.6.2.14 OPERATING MODE Register
        15. 9.6.2.15 DISCONNECT ENABLE Register
        16. 9.6.2.16 DETECT/CLASS ENABLE Register
        17. 9.6.2.17 Power Priority / 2Pair PCUT Disable Register Name
        18. 9.6.2.18 TIMING CONFIGURATION Register
        19. 9.6.2.19 GENERAL MASK Register
        20. 9.6.2.20 DETECT/CLASS RESTART Register
        21. 9.6.2.21 POWER ENABLE Register
        22. 9.6.2.22 RESET Register
        23. 9.6.2.23 ID Register
        24. 9.6.2.24 Connection Check and Auto Class Status Register
        25. 9.6.2.25 2-Pair Police Ch-1 Configuration Register
        26. 9.6.2.26 2-Pair Police Ch-2 Configuration Register
        27. 9.6.2.27 2-Pair Police Ch-3 Configuration Register
        28. 9.6.2.28 2-Pair Police Ch-4 Configuration Register
        29. 9.6.2.29 Capacitance (Legacy PD) Detection
        30. 9.6.2.30 Power-on Fault Register
        31. 9.6.2.31 PORT RE-MAPPING Register
        32. 9.6.2.32 Channels 1 and 2 Multi Bit Priority Register
        33. 9.6.2.33 Channels 3 and 4 Multi Bit Priority Register
        34. 9.6.2.34 4-Pair Wired and Port Power Allocation Register
        35. 9.6.2.35 4-Pair Police Ch-1 and 2 Configuration Register
        36. 9.6.2.36 4-Pair Police Ch-3 and 4 Configuration Register
        37. 9.6.2.37 TEMPERATURE Register
        38. 9.6.2.38 4-Pair Fault Configuration Register
        39. 9.6.2.39 INPUT VOLTAGE Register
        40. 9.6.2.40 CHANNEL 1 CURRENT Register
        41. 9.6.2.41 CHANNEL 2 CURRENT Register
        42. 9.6.2.42 CHANNEL 3 CURRENT Register
        43. 9.6.2.43 CHANNEL 4 CURRENT Register
        44. 9.6.2.44 CHANNEL 1 VOLTAGE Register
        45. 9.6.2.45 CHANNEL 2 VOLTAGE Register
        46. 9.6.2.46 CHANNEL 3 VOLTAGE Register
        47. 9.6.2.47 CHANNEL 4 VOLTAGE Register
        48. 9.6.2.48 2x FOLDBACK SELECTION Register
        49. 9.6.2.49 FIRMWARE REVISION Register
        50. 9.6.2.50 I2C WATCHDOG Register
        51. 9.6.2.51 DEVICE ID Register
        52. 9.6.2.52 CHANNEL 1 DETECT RESISTANCE Register
        53. 9.6.2.53 CHANNEL 2 DETECT RESISTANCE Register
        54. 9.6.2.54 CHANNEL 3 DETECT RESISTANCE Register
        55. 9.6.2.55 CHANNEL 4 DETECT RESISTANCE Register
        56. 9.6.2.56 CHANNEL 1 DETECT CAPACITANCE Register
        57. 9.6.2.57 CHANNEL 2 DETECT CAPACITANCE Register
        58. 9.6.2.58 CHANNEL 3 DETECT CAPACITANCE Register
        59. 9.6.2.59 CHANNEL 4 DETECT CAPACITANCE Register
        60. 9.6.2.60 CHANNEL 1 ASSIGNED CLASS Register
        61. 9.6.2.61 CHANNEL 2 ASSIGNED CLASS Register
        62. 9.6.2.62 CHANNEL 3 ASSIGNED CLASS Register
        63. 9.6.2.63 CHANNEL 4 ASSIGNED CLASS Register
        64. 9.6.2.64 AUTO CLASS CONTROL Register
        65. 9.6.2.65 CHANNEL 1 AUTO CLASS POWER Register
        66. 9.6.2.66 CHANNEL 2 AUTO CLASS POWER Register
        67. 9.6.2.67 CHANNEL 3 AUTO CLASS POWER Register
        68. 9.6.2.68 CHANNEL 4 AUTO CLASS POWER Register
        69. 9.6.2.69 ALTERNATIVE FOLDBACK Register
        70. 9.6.2.70 SRAM CONTROL Register
          1. 9.6.2.70.1 SRAM START ADDRESS (LSB) Register
          2. 9.6.2.70.2 SRAM START ADDRESS (MSB) Register
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Introduction to PoE
        1. 10.1.1.1 2-Pair Versus 4-Pair Power and the New IEEE802.3bt Standard
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Connections on Unused Channels
        2. 10.2.2.2 Power Pin Bypass Capacitors
        3. 10.2.2.3 Per Port Components
        4. 10.2.2.4 System Level Components (not Shown in the Schematic Diagrams)
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
    1. 11.1 VDD
    2. 11.2 VPWR
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Kelvin Current Sensing Resistors
    2. 12.2 Layout Example
      1. 12.2.1 Component Placement and Routing Guidelines
        1. 12.2.1.1 Power Pin Bypass Capacitors
        2. 12.2.1.2 Per-Port Components
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.4.4 DC Disconnect

Disconnect is the automated process of turning off power to the port. When the port is unloaded or at least falls below minimum load, turn off power to the port and restart detection. In DC disconnect, the voltage across the sense resistors is measured. When enabled, the DC disconnect function monitors the sense resistor voltage of a powered port to verify the port is drawing at least the minimum current to remain active. The TDIS timer counts up whenever the port current is below the disconnect threshold (6.5 mA or 4.5 mA depending on the port configuration). If a timeout occurs, the port is shut down and the corresponding disconnect bit in the Fault Event Register is set. In the case of a PD implementing MPS (maintain Power Signature) current pulsing, the TDIS counter is reset each time the current goes continuously higher than the disconnect threshold for at least 3 ms.

The TDIS duration is set by the TMPDO Bits of the Timing Configuration register (0x16).

Note:

If a Class 4 or lower 4-Pair Single Signature PD is connected, the TPS23881 will immediately power down one channel immediately after (no TMPDO timeout) the current falls below the disconnect threshold while leaving the second channel powered. This channel will be re-powered if the current on the remaining channel exceed 75mA. Alterntively if the current on the remaining channel falls below the disconnect threshold for longer than the TMPDO timeout, the port will be shut down and the corresponding disconnect bits in the Fault Event Register are set.

Note:

If both channels of a 4-Pair Dual Signature PD are powered, the DCDTx bit in register 0x2D is automatically set after turn on to ensure the IEEE compliant 4.5mA threshold is used.

Note:

If a 4-Pair Single Signature Class 5-8 PD is powered, the DCDTx bit in register 0x2D is automatically set after turn on to ensure the IEEE compliant 4.5mA threshold is used.