SLVSCM3B january   2015  – august 2023 TPS62065-Q1 , TPS62067-Q1

PRODUCTION DATA  

  1.   1
  2. Features
  3. Applications
  4. Description
  5. Revision History
  6. Device Comparison Table
  7. Pin Configuration and Functions
  8. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6.     Typical Characteristics
  9. Parameter Measurement Information
  10. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Mode Selection (TPS62065-Q1) and Forced PWM Mode (TPS62067A-Q1)
      2. 9.3.2 Power Good (PG, TPS62067x-Q1)
      3. 9.3.3 Enable
      4. 9.3.4 Shutdown and Output Discharge
      5. 9.3.5 Soft Start
      6. 9.3.6 Undervoltage Lockout (UVLO)
      7. 9.3.7 Internal Current Limit and Foldback Current Limit For Short-Circuit Protection
      8. 9.3.8 Clock Dithering
      9. 9.3.9 Thermal Shutdown
    4. 9.4 Device Functional Modes
      1. 9.4.1 Power Save Mode
        1. 9.4.1.1 Dynamic Voltage Positioning
        2. 9.4.1.2 100% Duty-Cycle Low-Dropout Operation
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Output Voltage Setting
        2. 10.2.2.2 Output Filter Design (Inductor And Output Capacitor)
          1. 10.2.2.2.1 Inductor Selection
          2. 10.2.2.2.2 Output Capacitor Selection
          3. 10.2.2.2.3 Input Capacitor Selection
        3. 10.2.2.3 Checking Loop Stability
      3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Power Good (PG, TPS62067x-Q1)

The Power Good (PG) pin indicates whether the output voltage has reached its regulation voltage. The PG pin can be used for sequencing of other system rails. The PG pin is an open-drain output that requires a pullup resistor to any voltage up to any voltage rail lower or equal the voltage applied to AVIN pin of the device. A 100-kΩ pullup resistor is recommended, and this value can be adjusted as described in the Choosing an Appropriate Pulllup/Pulldown Resistor for Open Drain Outputs Application Report.

If the power-good output is not used, it is recommended to tie to GND or leave open. The PG pin can sink a maximum of 1 mA. Table 9-1 shows the typical logic states of the PG pin.

Table 9-1 PG Pin Functional Table
DEVICE CONDITIONSPG STATUS
HIGH IMPEDANCELOW
EnableEN = High, VFB ≥ 0.57 V
EN = High, VFB ≤ 0.54 V
ShutdownEN = Low
Thermal ShutdownTJ > TJSD
UVLOVIN < VUVLOundefined