JAJSNB3 September   2023 LP5813

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Device Comparison
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
  9. 8 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Synchronous Boost Converter
        1. 9.3.1.1 Undervoltage Lockout
        2. 9.3.1.2 Enable and Soft Start
        3. 9.3.1.3 Switching Frequency
        4. 9.3.1.4 Current Limit Operation
        5. 9.3.1.5 Boost PWM Mode
        6. 9.3.1.6 Boost PFM Mode
        7. 9.3.1.7 Pass-Through Mode
      2. 9.3.2 Time-cross-multiplexing (TCM) scheme
        1. 9.3.2.1 Direct drive mode
        2. 9.3.2.2 TCM drive mode
        3. 9.3.2.3 Mix drive mode
        4. 9.3.2.4 Ghosting elimination
      3. 9.3.3 Analog Dimming
      4. 9.3.4 PWM Dimming
      5. 9.3.5 Autonomous Animation Engine Control
        1. 9.3.5.1 Animation Engine Pattern
        2. 9.3.5.2 Sloper
        3. 9.3.5.3 Animation Engine Unit (AEU)
        4. 9.3.5.4 Animation Pause Unit (APU)
      6. 9.3.6 Protections and Diagnostics
        1. 9.3.6.1 Overvoltage Protection
        2. 9.3.6.2 Output Short-to-Ground Protection
        3. 9.3.6.3 LED Open Detections
        4. 9.3.6.4 LED Short Detections
        5. 9.3.6.5 Thermal Shutdown
    4. 9.4 Device Functional Modes
    5. 9.5 Programming
    6. 9.6 Register Map Table
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Application
      2. 10.2.2 Design Parameters
      3. 10.2.3 Detailed Design Procedure
        1. 10.2.3.1 Inductor Selection
        2. 10.2.3.2 Output Capacitor Selection
        3. 10.2.3.3 Input Capacitor Selection
        4. 10.2.3.4 Program Procedure
        5. 10.2.3.5 Programming Example
      4. 10.2.4 Application Performance Plots
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
    2. 11.2 ドキュメントの更新通知を受け取る方法
    3. 11.3 サポート・リソース
    4. 11.4 Trademarks
    5. 11.5 静電気放電に関する注意事項
    6. 11.6 用語集
  13. 12Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

10.2.3.4 Program Procedure

After VIN powering up, the boost converter can be enabled by pulling EN to High. After around 1 ms for boost output and internal oscillator stable, the device can be initialized by configuring chip_en = 1. Then the CONFIG registers can be set to the excepted configuration. After updating the CONFIG registers, one update command must to be sent to make the configuration effective. Either manual mode or autonomous mode can be seleted for each LED. A new configuration is only effective once update command is received.

The detailed progeam procedure is illustrated as:

GUID-20230419-SS0I-SSP1-LX1J-KKNVPPTXFWPJ-low.svg Figure 10-4 Program Procedure