JAJSOE5H April   2006  – March 2022 PCA9536

PRODUCTION DATA  

  1. 特長
  2. アプリケーション
  3. 概要
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 I/O Port
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-On Reset
      2. 8.4.2 Powered-Up
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
    6. 8.6 Register Maps
      1. 8.6.1 Device Address
      2. 8.6.2 Control Register and Command Byte
      3. 8.6.3 Register Descriptions
      4. 8.6.4 Bus Transactions
        1. 8.6.4.1 Writes
        2. 8.6.4.2 Reads
  9. Application Information Disclaimer
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Minimizing ICC When I/Os Control LEDs
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Errata
    2. 10.2 System Impact
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 サポート・リソース
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSVCCMINTYP(1)MAXUNIT
VIKInput diode clamp voltageII = –18 mA2.3 V to 5.5 V–1.2

0

V
VPORRPower-on reset voltage, VCC risingVI = VCC or GND, IO = 01.21.6V
VPORFPower-on reset voltage, VCC fallingVI = VCC or GND, IO = 00.751V
VOHP-port high-level
output voltage(2)
IOH = –8 mA2.3 V1.8V
3 V2.6
4.5 V4.1
4.75 V4.1
IOH = –10 mA2.3 V1.7
3 V2.5
4.5 V4
4.75 V4
IOLSDAVOL = 0.4 V2.3 V to 5.5 V310mA
P-port(3)VOL = 0.5 V2.3 V810
3 V814
4.5 V817
4.75 V832
VOL = 0.7 V2.3 V1013
3 V1019
4.5 V1024
4.75 V1044
IISCL, SDAVI = VCC or GND2.3 V to 5.5 V±1μA
IIHP-portVI = VCC2.3 V to 5.5 V1μA
IILP-portVI = GND2.3 V to 5.5 V–100μA
ICCOperating modeVI = VCC, IO = 0,
I/O = inputs, fscl = 400 kHz
5.5 V73150μA
3.6 V950
2.7 V730
VI = VCC, IO = 0,
I/O = inputs, fscl = 100 kHz
5.5 V1425
3.6 V920
2.7 V615
Standby modeVI = GND, IO = 0,
I/O = inputs, fscl = 0 kHz
5.5 V225350
3.6 V175250
2.7 V125200
VI = VCC, IO = 0,
I/O = inputs, fscl = 0 kHz
5.5 V0.251.8
3.6 V0.21.2
2.7 V0.11
ΔICCAdditional current in
standby mode
One input at VCC – 0.6 V,
Other inputs at VCC or GND
2.3 V to 5.5 V0.35mA
Every LED I/O at VI = 4.3 V,
fscl = 0 kHz
5.5 V0.4
CiSCLVI = VCC or GND2.3 V to 5.5 V45pF
CioSDAVIO = VCC or GND2.3 V to 5.5 V56.5pF
P-port7.59.5
All typical values are at nominal supply voltage (2.5-, 3.3-, or 5-V VCC) and TA = 25°C.
The total current sourced by all I/Os must be limited to 85 mA.
Each I/O must be limited externally to a maximum of 25 mA, and the P-port (P3–P0) must be limited to a maximum current of 100 mA.