SLASF39 December   2023 TAD5112-Q1

ADVANCE INFORMATION  

  1.   1
  2. Features
  3. Applications
  4. Description
  5. Revision History
  6. Pin Configuration and Functions
  7. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Requirements: I2C Interface
    7. 6.7  Switching Characteristics: I2C Interface
    8. 6.8  Timing Requirements: SPI Interface
    9. 6.9  Switching Characteristics: SPI Interface
    10. 6.10 Timing Requirements: TDM, I2S or LJ Interface
    11. 6.11 Switching Characteristics: TDM, I2S or LJ Interface
  8. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Serial Interfaces
        1. 7.3.1.1 Control Serial Interfaces
        2. 7.3.1.2 Audio Serial Interfaces
          1. 7.3.1.2.1 Time Division Multiplexed Audio (TDM) Interface
          2. 7.3.1.2.2 Inter IC Sound (I2S) Interface
          3. 7.3.1.2.3 Left-Justified (LJ) Interface
        3. 7.3.1.3 Using Multiple Devices With Shared Buses
        4. 7.3.1.4 Phase-Locked Loop (PLL) and Clock Generation
        5. 7.3.1.5 Output Channel Configurations
        6. 7.3.1.6 Reference Voltage
        7. 7.3.1.7 Programmable Microphone Bias
        8. 7.3.1.8 Signal-Chain Processing
          1. 7.3.1.8.1 DAC Signal-Chain
            1. 7.3.1.8.1.1 Programmable Channel Gain and Digital Volume Control
            2. 7.3.1.8.1.2 Programmable Channel Gain Calibration
            3. 7.3.1.8.1.3 Programmable Digital High-Pass Filter
            4. 7.3.1.8.1.4 Programmable Digital Biquad Filters
            5. 7.3.1.8.1.5 Programmable Digital Mixer
            6. 7.3.1.8.1.6 Configurable Digital Interpolation Filters
              1. 7.3.1.8.1.6.1 Linear Phase Filters
                1. 7.3.1.8.1.6.1.1 Sampling Rate: 16 kHz or 14.7 kHz
                2. 7.3.1.8.1.6.1.2 Sampling Rate: 24 kHz or 22.05 kHz
                3. 7.3.1.8.1.6.1.3 Sampling Rate: 32 kHz or 29.4 kHz
                4. 7.3.1.8.1.6.1.4 Sampling Rate: 48 kHz or 44.1 kHz
                5. 7.3.1.8.1.6.1.5 Sampling Rate: 96 kHz or 88.2 kHz
                6. 7.3.1.8.1.6.1.6 Sampling Rate: 384 kHz or 352.8 kHz
        9. 7.3.1.9 Interrupts, Status, and Digital I/O Pin Multiplexing
    4. 7.4 Device Functional Modes
    5. 7.5 Register Maps
      1. 7.5.1 TAD5212_P0 Registers
      2. 7.5.2 TAD5212_P1 Registers
      3. 7.5.3 TAD5212_P3 Registers
  9. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
  10. Power Supply Recommendations
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報
Programmable Digital Biquad Filters

The device supports up to 12 programmable digital biquad filters available for DAC signal chain limited to 3/channel. These highly efficient filters achieve the desired frequence response. The TAD5112-Q1 also supports on the fly programmable Biquad filters for two channel playback use case. In digital signal processing, a digital biquad filter is a second-order, recursive linear filter with two poles and two zeros. Equation 2 gives the transfer function of each biquad filter:

Equation 2. GUID-BC2B8BC9-15A8-4F51-BCDC-655425304DBE-low.gif

The frequency response for the biquad filter section with default coefficients is flat at a gain of 0 dB (all-pass filter). The host device can override the frequency response by programming the biquad coefficients to achieve the desired frequency response for a low-pass, high-pass, or any other desired frequency shaping. As described in Table 7-16, these biquad filters can be allocated for each output channel based on the DAC_DSP_BQ_CFG[1:0] register setting of P0_R115. By setting DAC_DSP_BQ_CFG[1:0] to 2'b00, the biquad filtering for all playback channels are disabled and the host device can choose this setting if no additional filtering is required for the system application. See the TAC5212 Programmable Biquad Filter Configuration and Applications application report for further details.

Table 7-16 Biquad Filter Allocation to the Output Channel
PROGRAMMABLE BIQUAD FILTERRECORD OUTPUT CHANNEL ALLOCATION USING P0_R115_D[3:2] REGISTER SETTING
DAC_DSP_BQ_CFG[1:0] = 2'b01
(1 Biquad per Channel)
DAC_DSP_BQ_CFG[1:0] = 2'b10 (Default)
(2 Biquads per Channel)
DAC_DSP_BQ_CFG[1:0] = 2'b11
(3 Biquads per Channel)
Biquad filter 1Allocated to output channel 1Allocated to output channel 1Allocated to output channel 1
Biquad filter 2Allocated to output channel 2Allocated to output channel 2Allocated to output channel 2
Biquad filter 3Allocated to output channel 3Allocated to output channel 3Allocated to output channel 3
Biquad filter 4Allocated to output channel 4Allocated to output channel 4Allocated to output channel 4
Biquad filter 5 Not usedAllocated to output channel 1Allocated to output channel 1
Biquad filter 6Not usedAllocated to output channel 2Allocated to output channel 2
Biquad filter 7 Not usedAllocated to output channel 3Allocated to output channel 3
Biquad filter 8Not usedAllocated to output channel 4Allocated to output channel 4
Biquad filter 9 Not used Not usedAllocated to output channel 1
Biquad filter 10 Not usedNot usedAllocated to output channel 2
Biquad filter 11 Not used Not usedAllocated to output channel 3
Biquad filter 12 Not used Not usedAllocated to output channel 4

Table 7-17 shows the biquad filter coefficients mapping to the register space.

Table 7-17 Biquad Filter Coefficients Register Mapping
PROGRAMMABLE BIQUAD FILTERBIQUAD FILTER COEFFICIENTS REGISTER MAPPINGPROGRAMMABLE BIQUAD FILTERBIQUAD FILTER COEFFICIENTS REGISTER MAPPING
Biquad filter 1P16_R8-R27Biquad filter 7P17_R8-R27
Biquad filter 2P16_R28-R47Biquad filter 8P17_R28-R47
Biquad filter 3P16_R48-R67Biquad filter 9P17_R48-R67
Biquad filter 4P16_R68-R87Biquad filter 10P17_R68-R87
Biquad filter 5P16_R88-R107Biquad filter 11P17_R88-R107
Biquad filter 6P16_R108-R127Biquad filter 12P17_R108-R127