SLOS429C May   2004  – May 2016 TPA6204A1

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics: TA = 25°C
    6. 7.6 Operating Characteristics: TA = 25°C, Gain = 1 V/V
    7. 7.7 Dissipation Ratings
    8. 7.8 Typical Characteristics
  8. Parameter Measurement Information
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Advantages of Fully Differential Amplifiers
      2. 9.3.2 Fully Differential Amplifier Efficiency and Thermal Information
    4. 9.4 Device Functional Modes
      1. 9.4.1 Shutdown Mode
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Selecting Components for Resistors (RI)
        2. 10.2.2.2 Using Low-ESR Capacitors
          1. 10.2.2.2.1 Bypass Capacitor (C(BYPASS)) and Start-Up Time
          2. 10.2.2.2.2 Input Capacitor (CI)
          3. 10.2.2.2.3 Decoupling Capacitor (CS)
      3. 10.2.3 Application Curves
    3. 10.3 System Examples
  11. 11Power Supply Recommendations
    1. 11.1 Power Supply Decoupling Capacitor
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Community Resources
    2. 13.2 Trademarks
    3. 13.3 Electrostatic Discharge Caution
    4. 13.4 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

デバイスごとのパッケージ図は、PDF版データシートをご参照ください。

メカニカル・データ(パッケージ|ピン)
  • DRB|8
サーマルパッド・メカニカル・データ
発注情報

9 Detailed Description

9.1 Overview

The TPA6204A1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the amplifier outputs a differential voltage that is equal to the differential input times the gain. The common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless of the common-mode voltage at the input.

9.2 Functional Block Diagram

TPA6204A1 Block_Diagram_SLOS429.gif

9.3 Feature Description

9.3.1 Advantages of Fully Differential Amplifiers

  • Input coupling capacitors not required: A fully differential amplifier with good CMRR, like the TPA6204A1, allows the inputs to be biased at voltage other than mid-supply. For example, if a DAC has mid-supply lower than the mid-supply of the TPA6204A1, the common-mode feedback circuit adjusts for that, and the TPA6204A1 outputs are still biased at mid-supply of the TPA6204A1. The inputs of the TPA6204A1 can be biased from 0.5 V to VDD − 0.8 V. If the inputs are biased outside of that range, input coupling capacitors are required.
  • Mid-supply bypass capacitor, C(BYPASS), not required: The fully differential amplifier does not require a bypass capacitor. This is because any shift in the mid-supply affects both positive and negative channels equally and cancels at the differential output. It is important to remember that removing the bypass capacitor slightly worsens the kSVR. A slight decrease of kSVR, however, may be acceptable when an additional component can be eliminated.
  • Better RF-immunity: GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The transmitted signal is picked up on input and output traces. The fully differential amplifier cancels the signal much better than the typical audio amplifier.

9.3.2 Fully Differential Amplifier Efficiency and Thermal Information

Class-AB amplifiers are inefficient. The primary cause of these inefficiencies is voltage drop across the output stage transistors. There are two components of the internal voltage drop. One is the headroom or DC voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD. The internal voltage drop multiplied by the average value of the supply current, IDD(avg), determines the internal power dissipation of the amplifier.

An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 15).

TPA6204A1 voltage_current_waveforms_BTL_amp_slos429.gif Figure 15. Voltage and Current Waveforms for BTL Amplifiers

Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different. Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform. Figure 13 and are the basis for calculating amplifier efficiency.

Equation 1. TPA6204A1 eq_3_SLOS429.gif

where

    TPA6204A1 eq_4_SLOS429.gif

    where

    • PL = Power delivered to load
    • VLRMS = RMS voltage on BTL load
    • RL = Load resistance
    • VP = Peak voltage of BTL load
    TPA6204A1 eq_5_SLOS429.gif

    where

    • PSUP = Power drawn from power supply
    • RL = Load resistance
    • VP = Peak voltage of BTL load
    • IDDavg = Average current drawn from the power supply
    • VDD = Power supply voltage

Therefore,

Equation 2. TPA6204A1 eq_6_SLOS429.gif

Substituting PL and PSUP in Equation 5,

Equation 3. TPA6204A1 eq_7_SLOS429.gif

where

    TPA6204A1 eq_8_SLOS429.gif

Therefore,

Equation 4. TPA6204A1 eq_9_SLOS429.gif

where

  • ηBTL = Efficiency of a BTL amplifier

Table 2 and Table 3 employ Equation 5 to calculate efficiencies for four different output power levels. Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. For a 1-W audio system with 8-Ω loads and a 5-V supply, the maximum draw on the power supply is almost 1.6 W.

A final point to remember about Class-AB amplifiers is how to manipulate the terms in the efficiency equation to the utmost advantage when possible.

A simple formula for calculating the maximum power dissipated, PDmax, may be used for a differential output application:

Equation 5. TPA6204A1 eq_12_SLOS429.gif

The PDmax for a 5-V, 8-Ω system is 0.64 W.

The maximum ambient temperature depends on the heat sinking ability of the PCB system. The derating factor for the 3 mm × 3 mm DRB package is shown in the dissipation rating table. Converting this to RθJA:

Equation 6. TPA6204A1 eq_10_SLOS429.gif

Given RθJA, the maximum allowable junction temperature, and the maximum internal dissipation, the maximum ambient temperature can be calculated with the following equation. The maximum recommended junction temperature for the TPA6204A1 is 150°C.

Equation 7. TPA6204A1 eq_11_SLOS429.gif
= 150 – 45.9(0.64) = 120.6°C

Equation 7 shows that the maximum ambient temperature is 120.6°C (package limited to 85°C) at maximum power dissipation with a 5-V supply.

Table 2 shows that for most applications no airflow is required to keep junction temperatures in the specified range. The TPA6204A1 is designed with thermal protection that turns the device off when the junction temperature surpasses 150°C to prevent damage to the IC. In addition, using speakers with an impedance higher than 8-Ω dramatically increases the thermal performance by reducing the output current.

Table 2. Efficiency and Maximum Ambient Temperature vs Output Power in 3.6-V 8-Ω BTL Systems(1)

OUTPUT POWER (W) EFFICIENCY (%) INTERNAL DISSIPATION (W) POWER FROM SUPPLY (W) MAX AMBIENT TEMPERATURE(2) (°C)
0.1 27.6 0.262 0.36 85
0.2 39.0 0.312 0.51 85
0.5 61.7 0.310 0.81 85
0.6 67.6 0.288 0.89 85
(1) DRB package
(2) Package limited to 85°C ambient

Table 3. Efficiency and Maximum Ambient Temperature vs Output Power in 5-V 8-Ω Systems(1)

OUTPUT POWER (W) EFFICIENCY (%) INTERNAL DISSIPATION (W) POWER FROM SUPPLY (W) MAX AMBIENT TEMPERATURE(2) (°C)
0.5 44.4 0.625 1.13 85
1 62.8 0.592 1.60 85
1.36 73.3 0.496 1.86 85
1.7 81.9 0.375 2.08 85
(1) DRB package
(2) Package limited to 85°C ambient

9.4 Device Functional Modes

9.4.1 Shutdown Mode

The TPA6204A1 can be put in shutdown mode when asserting SHUTDOWN pin to a logic LOW level. While in shutdown mode, the device is turned off, making the current consumption very low. The device exits shutdown mode when a HIGH logic level is applied to SHUTDOWN pin.