JAJSJ29D May   2020  – October 2021 TPS61378-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  VCC Power Supply
      2. 8.3.2  Input Undervoltage Lockout (UVLO)
      3. 8.3.3  Enable and Soft Start
      4. 8.3.4  Shut Down
      5. 8.3.5  Switching Frequency Setting
      6. 8.3.6  Spread Spectrum Frequency Modulation
      7. 8.3.7  Adjustable Peak Current Limit
      8. 8.3.8  Bootstrap
      9. 8.3.9  Load Disconnect
      10. 8.3.10 MODE/SYNC Configuration
      11. 8.3.11 Overvoltage Protection (OVP)
      12. 8.3.12 Output Short Protection/Hiccup
      13. 8.3.13 Power-Good Indicator
      14. 8.3.14 Thermal Shutdown
    4. 8.4 Device Functional Modes
      1. 8.4.1 Forced PWM Mode
      2. 8.4.2 Auto PFM Mode
      3. 8.4.3 External Clock Synchronization
      4. 8.4.4 Down Mode
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Programming the Output Voltage
        2. 9.2.2.2 Setting the Switching Frequency
        3. 9.2.2.3 Setting the Current Limit
        4. 9.2.2.4 Selecting the Inductor
        5. 9.2.2.5 Selecting the Output Capacitors
        6. 9.2.2.6 Selecting the Input Capacitors
        7. 9.2.2.7 Loop Stability and Compensation
          1. 9.2.2.7.1 Small Signal Model
          2. 9.2.2.7.2 Loop Compensation Design Steps
          3. 9.2.2.7.3 Selecting the Bootstrap Capacitor
          4. 9.2.2.7.4 VCC Capacitor
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 サポート・リソース
    4. 12.4 Trademarks
    5. 12.5 Glossary
    6. 12.6 Electrostatic Discharge Caution
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.3.12 Output Short Protection/Hiccup

In addition to the cycle-by-cycle current limit function, the TPS61378-Q1 also has output short protection. If the output current causes the low-side FET to reach current limit and pull the output voltage below the input voltage, the device enters into short circuit protection mode, triggering the hiccup timer. When the hiccup timer is triggered, the device limits the current to a relative lower level for 1.8 ms and then shuts down. After 67 ms, it will restart. If the short condition disappears, the device will automatically restart.

When FB voltage is below ≤ 0.1 V during fault condition, the current limit threshold is reduced to 1/5 of the programmed current limit. Frequency is clamped to 1.1 MHz if the FREQ pin setting is greater than 1.1 MHz.