SBVU081 june   2023

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1Introduction
    1. 1.1 Before You Begin
  5. 2EVM Setup
    1. 2.1 Inputs/Outputs Connectors and Jumper Descriptions
      1. 2.1.1  J1 – IN
      2. 2.1.2  J2 – OUT
      3. 2.1.3  J3
      4. 2.1.4  TP1 – IN
      5. 2.1.5  TP2 – PG
      6. 2.1.6  TP3 – SNS
      7. 2.1.7  TP4 – PG_FB
      8. 2.1.8  TP5 – OUT
      9. 2.1.9  TP6 – EN
      10. 2.1.10 TP7 – GND
      11. 2.1.11 TP8 – GND
    2. 2.2 Soldering Guidelines
    3. 2.3 Equipment Connections
  6. 3Operation
  7. 4Schematic
  8. 5PCB Layout
  9. 6Bill of Materials

6 Bill of Materials

Table 6-1 shows the bill of materials (BOM) for this EVM.

Table 6-1 TPS7A96EVM-106 BOM(1)(2)(3)(4)
DESIGNATOR QTY VALUE DESCRIPTION PACKAGE REFERENCE PART NUMBER MANUFACTURER ALTERNATE PART NUMBER ALTERNATE MANUFACTURER
!PCB1 1 Printed Circuit Board LP106 Any
C2, C4 2 10uF CAP, CERM, 10 µF, 16 V,+/- 10%, X7R, 0805 805 EMK212BB7106KG-T Taiyo Yuden
C7 1 4.7µF Cap Ceramic 4.7uF 50 V X7R 10% Pad SMD 0805 +125°C Automotive T/R 805 CGA4J1X7R1H475K125AC TDK Corporation
H9, H10, H11, H12 4 Bumpon, Hemisphere, 0.44 X 0.20, Clear Transparent Bumpon SJ-5303 (CLEAR) 3M
H13, H14, H15, H16 4 RFI SHIELD CLIP TIN SMD RFI SHIELD CLIP TIN SMD S2711-46R Harwin
J1, J2 2 BNC Connector Jack, Female Socket 50Ohm Through Hole Solder PTH_BNC_JACK_VERT 4578 Pomona Electronics
MP1 1 SMT_RF-SHIELD S01-50250500 Harwin
R1 1 0 RES, 0, 1%, 0.1 W, AEC-Q200 Grade 0, 0603 603 RMCF0603ZT0R00 Stackpole Electronics Inc
R2, R4, R5 3 10.0k RES, 10.0 k, 1%, 0.1 W, AEC-Q200 Grade 0, 0603 603 RMCF0603FT10K0 Stackpole Electronics Inc
R3 1 187k RES, 187 k, 1%, 0.1 W, 0603 603 RC0603FR-07187KL Yageo
R6 1 22k 22 kOhms ±1% 0.1W, 1/10W Chip Resistor 0603 (1608 Metric) Thick Film 603 CRCW060322K0FKEAC Vishay
R7 1 12.4k RES, 12.4 k, 1%, 0.1 W, 0603 603 RC0603FR-0712K4L Yageo
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 8 Test Point, Compact, SMT Testpoint_Keystone_Compact 5016 Keystone
U1 1 2-A, Ultra-low Noise, Ultra-high PSRR, RF Voltage Regulator VSON10 TPS7A9601DSCR Texas Instruments
(1) This assembly is ESD sensitive; observe ESD precautions.
(2) This assembly must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.
(3) This assembly must comply with workmanship standards IPC-A-610 Class 2.
(4) Unless otherwise noted in the Alternate Part Number or Alternate Manufacturer columns, all parts can be substituted with equivalents.