SLAS778C February   2013  – September 2021 TAS2505

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  I2S/LJF/RJF Timing in Master Mode
    7. 6.7  I2S/LJF/RJF Timing in Slave Mode
    8. 6.8  DSP Timing in Master Mode
    9. 6.9  DSP Timing in Slave Mode
    10. 6.10 I2C Interface Timing
    11. 6.11 SPI Interface Timing
    12. 6.12 Typical Characteristics
      1. 6.12.1 Class D Speaker Driver Performance
      2. 6.12.2 HP Driver Performance
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Audio Analog I/O
      2. 7.3.2 Audio DAC and Audio Analog Outputs
      3. 7.3.3 DAC
      4. 7.3.4 POR
      5. 7.3.5 CLOCK Generation and PLL
    4. 7.4 Device Functional Modes
      1. 7.4.1 Digital Pins
      2. 7.4.2 Analog Pins
      3. 7.4.3 Multifunction Pins
      4. 7.4.4 Analog Signals
        1. 7.4.4.1 Analog Inputs AINL and AINR
      5. 7.4.5 DAC Processing Blocks — Overview
      6. 7.4.6 Digital Mixing and Routing
      7. 7.4.7 Analog Audio Routing
      8. 7.4.8 Digital Audio and Control Interface
        1. 7.4.8.1 Digital Audio Interface
        2. 7.4.8.2 Control Interface
          1. 7.4.8.2.1 I2C Control Mode
          2. 7.4.8.2.2 SPI Digital Interface
        3. 7.4.8.3 Device Special Functions
    5. 7.5 Register Map
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 Typical Configuration
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
        3. 8.2.1.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
  12. 12Mechanical, Packaging, and Orderable Information

CLOCK Generation and PLL

The TAS2505 supports a wide range of options for generating clocks for the DAC sections as well as interface and other control blocks. The clocks for the DAC require a source reference clock. This clock can be provided on a variety of device pins, such as the MCLK, BCLK, or GPIO pins. The source reference clock for the codec can be chosen by programming the CODEC_CLKIN value on page 0, register 4, bits D1–D0. The CODEC_CLKIN can then be routed through highly-flexible clock dividers shown in Figure 2 through 7 in the TAS2505 Application Reference Guide to generate the various clocks required for the DAC and the Digital Effects section also found in the TAS2505 Application Reference Guide (SLAU472). In the event that the desired audio clocks cannot be generated from the reference clocks on MCLK, BCLK, or GPIO, the TAS2505 also provides the option of using the on-chip PLL which supports a wide range of fractional multiplication values to generate the required clocks. Starting from CODEC_CLKIN, the TAS2505 provides several programmable clock dividers to help achieve a variety of sampling rates for the DAC and clocks for the Digital Effects sections.

For more detailed information see the TAS2505 Application Reference Guide (SLAU472).